Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Aug 27, 2012, 12:42 PM
kad is offline
kad
Find More Posts by kad
kad
Quad Crasher
kad's Avatar
Quote:
Originally Posted by Dialfonzo View Post
I have design the frame for HK10g motors.
I don't think they are the one you're using... No?
I'm using the iPower 10g motors, but if you look at the two, they are identical except for the iPower being rated for 2s or 3s instead of just 2s like the HKs.

-K
Sign up now
to remove ads between posts
Old Aug 27, 2012, 02:15 PM
jinsing is offline
Find More Posts by jinsing
Registered User
jinsing's Avatar
I have it connected to the 5v I2c, but did not load any firmware into the gps.
I will give that a try when I get home.
I did download the current firmware from qcrc's link.
Old Aug 27, 2012, 04:45 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by kad View Post
I'm using the iPower 10g motors, but if you look at the two, they are identical except for the iPower being rated for 2s or 3s instead of just 2s like the HKs.

-K
Ok i will thrust you on that.
Hard to look on a cellphone far away from home.

Making a 4in1 adapter to connect them all to the receiver is what i would do in your case.

If a motor is lower in kv you would notice there too

Eric
RCG Plus Member
Old Aug 27, 2012, 08:47 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
`Dialfonzo I am sending you a PM, having a small issue with the mini wii.
Old Aug 28, 2012, 08:21 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Hey guys I am having a small issue. I am trying to upload the 2.1 or even 2.0 to my miniwii board, I am using the right usb ftdi programmer, I have everything defined in arduino 1.01 or 1.0 resp, and every time I try to upload the code, I get avrdude sync not in sync with some numbers etc. but says done uploading above it. but the code is not actually on there, I tried using the gui and nothing. Not sure what this can be anyone have any ideas. it is the only thing now holding me back from flying this little jem.
Old Aug 28, 2012, 09:09 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Here is a pic of the error I am getting. any one have any ideas. I just got the ftdi yesterday. and I tried it on another board and it worked fine. but on my mini wii no matter which board I select etc. it does not want to load the code and it gives this message. Hope someone can help.
Old Aug 28, 2012, 09:39 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins View Post
Here is a pic of the error I am getting. any one have any ideas. I just got the ftdi yesterday. and I tried it on another board and it worked fine. but on my mini wii no matter which board I select etc. it does not want to load the code and it gives this message. Hope someone can help.
On a cellphone with near no signal.. So a bit hard... lol

Quick Google search

http://www.arduino.cc/cgi-bin/yabb2/...1248528012/all
RCG Plus Member
Old Aug 28, 2012, 09:42 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by Dialfonzo View Post
On a cellphone with near no signal.. So a bit hard... lol

Quick Google search

http://www.arduino.cc/cgi-bin/yabb2/...1248528012/all
Try GUI in 1.9 to 2.1 since i don't remember the one that is in there.

To known if you have serial communication
RCG Plus Member
Old Aug 28, 2012, 09:52 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Yep that was a no go. also you said something about a reset button, I have gone over the entire board and there is no reset button.
Old Aug 28, 2012, 09:59 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins View Post
Yep that was a no go. also you said something about a reset button, I have gone over the entire board and there is no reset button.
There is no reset button on that board.

What kind of ftdi you have?
You tried all boards in the list?
RCG Plus Member
Old Aug 28, 2012, 10:03 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
I have a 5v basic ftdi, not all boards yet. I just tried opening the 1.9 but that is another problem. will not compile in .22 and will not compile in 1.0 it is weird. I know it is not the board it looks to be working right. just can't get code on it.
Old Aug 28, 2012, 10:12 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
just tried all boards on the list. and I checked the com port. etc. but it will not load, the lights on the board flash like they should, but the ftdi the lights blink at first then stop. but with my other board they blink bright through the whole upload process. and no matter what I do I still get that error avrdude sync thing every time.
Old Aug 29, 2012, 03:50 PM
jinsing is offline
Find More Posts by jinsing
Registered User
jinsing's Avatar
Waiting on an ftdi I decided to work on lights. I think I'm still missing something lolName: ImageUploadedByTapatalk1346269561.292122.jpg
Views: 86
Size: 45.5 KB
Description: Name: ImageUploadedByTapatalk1346269799.550307.jpg
Views: 96
Size: 59.2 KB
Description:
Old Aug 29, 2012, 04:43 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
--awesome--
RCG Plus Member
Old Aug 29, 2012, 05:00 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Hey Dialfonzo, I should have the new ftdi in a few days and will try it. will post how it goes.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Bledi-DiaLFonZo Copter VTail HUNTER 400 CANOPY + Addons Innerbreed Multirotor Talk 42 Sep 20, 2013 10:41 PM