Thread Tools
Jun 22, 2012, 01:48 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Or like that
(got a jet with similar EDF and they where very powerfull)

http://www.hobbyking.com/hobbycity/s...ssembled_.html
Sign up now
to remove ads between posts
Jun 22, 2012, 01:52 PM
Multirotor Builder!!!!!
Might work, but with edf's in general you will need bigger esc's
Jun 22, 2012, 02:00 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins
Might work, but with edf's in general you will need bigger esc's
Want to jump in..?
Jun 22, 2012, 02:06 PM
Multirotor Builder!!!!!
What do you mean?
Jun 22, 2012, 02:07 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins
What do you mean?
You have any interest in such a frame.. ?
In which configuration ?
Jun 22, 2012, 02:09 PM
Multirotor Builder!!!!!
an edf frame would be cool. I would be happy to test one out. it is just a matter of finding the right esc's and edf units. I will look around. will try to find a setup that uses the smallest esc possible but puts alot of power out.
Jun 22, 2012, 02:10 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins
an edf frame would be cool. I would be happy to test one out. it is just a matter of finding the right esc's and edf units. I will look around. will try to find a setup that uses the smallest esc possible but puts alot of power out.
Perfect..
Once we have a hardware setup we can work the frame on that.
Which config ? (Quad.. ?)
Jun 22, 2012, 02:14 PM
Multirotor Builder!!!!!
that would be best to start with.
Jun 22, 2012, 02:15 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by tc3wins
that would be best to start with.
Would give more usefull thrust than the VTail
We can jump to my Special Project thread ?
Jun 22, 2012, 02:18 PM
Multirotor Builder!!!!!
that works
Jun 22, 2012, 03:19 PM
Registered User
Not sure the small diameter fans will give enough torque reaction to control heading in a quad configuration, the vtail may be a better bet.
Jun 22, 2012, 03:37 PM
Old Flying Bastard
Kipkool's Avatar
Or servo on all arms to control duct direction ?
Jun 22, 2012, 04:37 PM
Registered User

DiaLFonZo V-Tail Frame 500mm - Mild Flips and Spins


New video of V-Tail 500mm with the thicker top and bottom rear arm. Seems to be more solid and didn't notice any issue with the weight gain. First time to open her up and do flips :-)

The orientation on this frame makes it such a joy to fly.

DiaLFonZo V-Tail Frame 500mm - Mild Flips and Spins (5 min 29 sec)
Last edited by cquian; Jun 22, 2012 at 06:20 PM.
Jun 22, 2012, 07:59 PM
Old Flying Bastard
Kipkool's Avatar
Hell yeah! That's a damn good flight
Jun 23, 2012, 09:29 AM
Old Flying Bastard
Kipkool's Avatar
First outdoor flight with the Wookong and new mix table ( same mix as VTAIL_YAW below ). EProps Graupner 10x5 , 4S 3300 lipo. RcTimer 750KV Same motors same props on all side.

http://www.youtube.com/watch?v=LVN4T...ature=youtu.be

Level mode only here. It's really smooth.

Video sucks as usual...
Last edited by Kipkool; Jun 23, 2012 at 09:58 AM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Bledi-DiaLFonZo Copter VTail HUNTER 400 CANOPY + Addons Innerbreed Multirotor Drone Talk 42 Sep 20, 2013 09:41 PM