Thread Tools
Mar 20, 2012, 05:59 AM
Registered User
Coenraad's Avatar
Question

How wet is too wet for a non waterproof truck?


Hey guys, i have recently gotten my first RC car, a ECX Torment.
But i am a little curious as to how much moist would be safe to drive in?
I assume wet grass is just a big no-no. But how about damp- (not soaking wet) mud/clay or sand/ gravel?

I used some hard frozen snow piles as a ramp to jump, wich seemed okey. But i don't really want to blow up the electronics on it.
Sign up now
to remove ads between posts
Mar 20, 2012, 07:55 AM
Registered User
D_FAST's Avatar
Most of us use an overtray. To help keep things dry and clean. You night not have luck finding a direct bolt on, modifying something close will be your best bet. Most electronic these days are splash proof.
Mar 20, 2012, 11:56 AM
Registered User
Coenraad's Avatar
Ah okey, does that not remove to much airflow so things heat up? Or is an overtray not totaly closed?
Mar 24, 2012, 02:19 AM
Registered User
traxx de maxx's Avatar
sand is maybe the worst place to run an rc. unless you strip every moving part down and clean it out after every run
Mar 28, 2012, 04:17 AM
Registered User
Coenraad's Avatar
Yeah i suppose sand can kill an electric motor quite fast.
Mar 28, 2012, 04:33 AM
Registered User
traxx de maxx's Avatar
not to mention every bearing. Plus where there is sand there is salt water which corrodes metal much faster than fresh water.
Unless you have bought lots of sand and use it in your back yard.
Mar 29, 2012, 06:09 AM
Registered User
Coenraad's Avatar
Beach sand would be quite bad i suppose yeah. But i think the hard stuff would be quite fun to drive on.

Just clean the car after running on messy undergrounds and you will keep the system running for a lot longer.
Just like with any machinery/technical stuff, maintainence keeps things in good shape, without it stuff breaks down faily quick.
Mar 31, 2012, 02:40 PM
Outdoor Extremist
rustlererad3's Avatar
I often bash in the sand pit that they built at a local part and when you don't clean the truck it ruins bearings, learned this lesson the hard way but sand is a lot of fun, and theres always the platidip approach to waterproofing things I havent researched that enough to decide if I am going to try that yet but another great thing is always changing out electronics
Apr 03, 2012, 01:03 AM
Registered User
Coenraad's Avatar
I found out how much moist it can take. Absolutely none!
My truch started to behave weird, and sudenly lost forward power. After i took it to my LHS for a check it showed that there was moist in both the ESC and the RX.

So do not use hard packed snow piles to jump over or even the slightest damp grass.

Staying far away from moist with my Torment now.

PS. i put some cloth around the engine holes, so no tiny stones or sand can get in.
Apr 03, 2012, 03:47 PM
Registered User
Quote:
Originally Posted by Coenraad View Post
I found out how much moist it can take. Absolutely none!
My truch started to behave weird, and sudenly lost forward power. After i took it to my LHS for a check it showed that there was moist in both the ESC and the RX.

So do not use hard packed snow piles to jump over or even the slightest damp grass.

Staying far away from moist with my Torment now.

PS. i put some cloth around the engine holes, so no tiny stones or sand can get in.
I suspect what happened is when you brought the truck back into the house the cold parts caused the water vapour in the air to condense on your electric bits, plus whatever snow may have melted on/in there.

Usually a situation like this only requires a thorough drying of the electronics before they will work normally again. Next time bring your truck inside and remove the cases from the ESC and rx if you can, and let them dry or hit them with the hair dryer. Did this the other day with my truck that tipped over on the edge of a creek. Stopped working right, dried it out, and now it's good to go again.

However, it's obviously way more fun if you can run your vehicle in moist/wet environments without worrying, so get a bottle/can of corrosion-x and dip or thoroughly spray the esc and rx (cases off!) with it. The boat and seaplane guys have been using this stuff for a long time with great success. (I think there is a video on youtube of a guy running his ESC, rx, and servo all completely submerged with no problems.)
Sep 25, 2012, 10:32 AM
Registered User
Name: Mad Truck Hheng Long.jpg
Views: 346
Size: 61.7 KB
Description: Just that protect your Truck! keep it simple!
Hy guys, just that protect your truck! just a plastic bottle with Velcro!
Feb 03, 2013, 09:23 AM
Registered User
Quote:
Originally Posted by gussilva2 View Post
Hy guys, just that protect your truck! just a plastic bottle with Velcro!

That's a neat idea.One question, don't the moister get up inside the bottle, where the antenna is?? I have a torment and it says its water-proof but only for like lil puddles. Thanks!
Feb 03, 2013, 01:02 PM
Registered User
traxx de maxx's Avatar
i used a similar thing but only covered the front area, you need air flow to keep things cool.
Dec 29, 2015, 11:26 AM
Registered User
hi I have an FTX VANTAGE 1/10 BRUSHED BUGGY 4WD RTR 2.4GHZ/WATERPROOF and I just want to ask if this 320A Brushed Brush Speed Controller ESC RC Car Truck Boat Reverse 1/8 1/10 will fit my car if you know please let me know with the answer.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion For all radio geeks (and non geeks too) oldcoot88 Life, The Universe, and Politics 18 Jan 29, 2012 06:39 PM
Discussion Latest Firmware - Yaw Is Bad For Non GPS Too - Resolved! Earl E Adobtr Aerial Photography 15 Dec 29, 2011 07:42 PM
Help! how do u make esc waterproof tekin rx8 combo etc and more sytem to make waterproof stampede vxl Off-road Cars 7 Dec 24, 2010 09:32 PM
For Sale Brand new MCX for a waterproof rc truck or car edu01jose Cars - Trucks and Parts (FS/W) 2 Feb 14, 2009 04:39 PM