Thread Tools
Mar 08, 2012, 11:54 AM
Registered User
CheckSum's Avatar
New Product

Turnigy Integrated PCB Micro-Quad


Turnigy Integrated PCB Micro-Quad


Features:
Light weight design.
Integrated PCB for component installation.
Included a full set of frame and mounting hardware.

Specs:
Flying Weight: 145g
Width: 250mm
Height: 85mm
마이크로 쿼드 (1 min 49 sec)
Last edited by CheckSum; Mar 09, 2012 at 05:44 PM.
Sign up now
to remove ads between posts
Mar 08, 2012, 12:10 PM
Ordered one earlier today for review.
Mar 08, 2012, 12:12 PM
Registered User
CheckSum's Avatar
^^I should too, but I promised my wife I would not buy any hobby stuff this pay period
Mar 08, 2012, 12:30 PM
Rank Amatuer
FullmoonCat's Avatar
That looks sweet. Wish that had been out before I built my microquad, but oh well. I don't need another one now.
Mar 08, 2012, 01:05 PM
Quad Erat Demonstrandum
scousethief's Avatar
No place for receiver ? underslung batt , fc on top .....rx ?
Mar 08, 2012, 01:09 PM
Quote:
Originally Posted by scousethief
No place for receiver ? underslung batt , fc on top .....rx ?
Its much like most micro sized frames. FC on top, Rx above that or on arm, Battery underneath.
Mar 08, 2012, 02:38 PM
Z06 Tony's Avatar
Thats a heavy frame for the size. The PCB power distro in the center is a great idea. All that weight in the arms only to solder the motors wires 1/8" from the ESC? It would be better to solder the motor wires direct so now no need for the PCB arms.
Mar 08, 2012, 02:50 PM
1.21 Gigawatts!
Steph280's Avatar
But the spec says light weight so it must be light! LOL
Mar 08, 2012, 03:02 PM
Registered User
Quote:
Originally Posted by Z06 Tony
Thats a heavy frame for the size. The PCB power distro in the center is a great idea. All that weight in the arms only to solder the motors wires 1/8" from the ESC? It would be better to solder the motor wires direct so now no need for the PCB arms.
It does seem a little heavy Tony. But that is what a little bigger motor and 3s is for.
Mar 08, 2012, 03:04 PM
Rank Amatuer
FullmoonCat's Avatar
It doesn't actually say what the weight of the frame is by itself, though. It states an estimated weight for the entire setup with motors and escs. I can't imagine it's that heavy, though probably heavier than the BlueSkyRC funsized frame, since it has legs.
Mar 08, 2012, 03:04 PM
Well my BlueSkyRC frame with everything but the lipo is 188g so 145g for this less Rx seems within range.

And I don't think the entire arm is copper clad, just the 3 tab strips on the end of each or so it looks from the pics.

Last edited by flitelab; Mar 08, 2012 at 03:19 PM.
Mar 08, 2012, 03:16 PM
Z06 Tony's Avatar
Im sorry I had it wrong. I seen 145g and thought that was just for the frame alone. It looks like the flying weight is 145g if you use the stuff suggested minus batt,RX. The price is right thats for sure.
Mar 08, 2012, 03:33 PM
Registered User
I don't mind the design, everything seems well protected. Not sure about ESC airflow.
Mar 08, 2012, 03:35 PM
Quote:
Originally Posted by Erknie
I don't mind the design, everything seems well protected. Not sure about ESC airflow.
On my other micros I have the ESCs all wedge into the central frame and not had any heat issues. Not as if your drawing a large amount from them. I usually run 10A ESCs on these micros.
Mar 08, 2012, 03:44 PM
Registered User
What sort of glue would you use to assemble it?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Can i remove integrated esc bec (turnigy plush) Axefly Power Systems 12 Dec 28, 2014 01:19 PM
For Sale Micro Quad (9") + Parts for a new micro quad (ESC's + motors) ed.ge Aircraft - Electric - Multirotor (FS/W) 8 Jan 17, 2012 04:41 AM
Discussion cute UM quad :) - the flying PCB axelen Scratchbuilt Indoor and Micro Models 10 May 05, 2011 06:33 PM
For Sale Tri-Quad controller PCB populated EnigmaSoar Aircraft - Electric - Helis (FS/W) 3 Apr 15, 2011 06:13 AM
Sold TriCopter / Quad PCB's (3) EnigmaSoar Aircraft - Electric - Helis (FS/W) 2 Mar 21, 2011 04:41 PM