Thread Tools
Apr 29, 2012, 01:32 AM
Barefeet
ChrisCurry's Avatar
Quote:
Originally Posted by PITPUP
Ok question to everyone . what is the best way to maintain access to the lift fan motor should it be needed ?. Once the rear area construction is complete it appears that it is all sealed and no access is available. how have you all approached this issue ?. Cheers.
I thought about that for a while and ended up having the entire top of the craft removable. The cabin has two tougues at the front that slot into the front of the craft and there are two clips at the rear. Makes access a pleasure.
Sign up now
to remove ads between posts
Apr 29, 2012, 01:40 AM
Barefeet
ChrisCurry's Avatar
Quote:
Originally Posted by PITPUP
Ok question to everyone . what is the best way to maintain access to the lift fan motor should it be needed ?. Once the rear area construction is complete it appears that it is all sealed and no access is available. how have you all approached this issue ?. Cheers.
I thought about that for a while and ended up having the entire top of the craft removable. The cabin has two tougues at the front that slot into the front of the craft and there are two clips at the rear. Makes access a pleasure.
Apr 29, 2012, 02:02 AM
Barefeet
ChrisCurry's Avatar
Justa few comments on what worked for me with the fan. I removed the circlip from the back of my motor so i can just grab the fan and pull it off along with the motors bell when needed as i bolted the fan directly to the bell. I had the craft on its side and put the fan back and the shaft only went a few mm into the top bearing. When i let go it turned and thats when i saw it needed balancing. A few small washers and some cyno later, the fan seemed to be balanced. It is now very smooth in operation so although not dynamically balanced, its good enough.
Apr 29, 2012, 08:58 AM
Registered User
Quote:
Originally Posted by ChrisCurry
I thought about that for a while and ended up having the entire top of the craft removable. The cabin has two tougues at the front that slot into the front of the craft and there are two clips at the rear. Makes access a pleasure.
Any chance of a pic of this please?
Apr 30, 2012, 02:28 AM
Barefeet
ChrisCurry's Avatar
I'll post wednesday. Its a long weekend in s.africa so am away
May 01, 2012, 07:37 PM
Registered User
Wonder why my Egde Hovercraft sinks in the front? Leak? Battery loosin power? Any ideas for powering up the 9.v NiCd?
May 02, 2012, 05:52 AM
Barefeet
ChrisCurry's Avatar
Quote:
Originally Posted by Mike Avans
Wonder why my Egde Hovercraft sinks in the front? Leak? Battery loosin power? Any ideas for powering up the 9.v NiCd?
Does it sink under power or when stationary?
May 02, 2012, 11:16 AM
Barefeet
ChrisCurry's Avatar
Here is my hovercraft and deck. Nice hey!Name: ImageUploadedByTapatalk1335975400.199024.jpg
Views: 231
Size: 64.2 KB
Description:
May 02, 2012, 12:17 PM
Registered User
Very neat! But where is the motor which drives the impeller - in the removable section or is it below the impeller?

A few more pics of my progress below. Tail fins and ailerons now in place - made from Balsa covered with 0.6oz/m2 fibreglass cloth coated with Eze-Kote water-based resin. Hinges for the lifting front door also fixed on.

I saw the original Hovertravel SR.N6 at Hoverworld 2012 in Lee-on-Solent last weekend. Still very impressive although you have to be short to stand upright in the cabin! If anyone wants pics, I could post these on the site or PM me with an e-mail address.
May 02, 2012, 01:58 PM
Barefeet
ChrisCurry's Avatar
Name: ImageUploadedByTapatalk1335985005.115282.jpg
Views: 264
Size: 74.7 KB
Description:

Here you go. Fan simply attached straight onto the motor. It got a little warm so i glued 2 pieces of wood next to the motor vents and they work!
May 02, 2012, 02:01 PM
Barefeet
ChrisCurry's Avatar
JeremyBB i would love to see the pics. I went on one in my youth - around 1969 - and don't remember much about the size of the craft but what a trip!
May 02, 2012, 02:54 PM
Registered User
The SR.N6 is in a warehouse, so the pictures are inevitably close-up. However, they do show some detail useful to modellers and there are many pics of an SR.N6 in operation, including the one at the start of this thread.
May 02, 2012, 04:24 PM
Registered User
More pics from the museum
May 03, 2012, 09:50 AM
Barefeet
ChrisCurry's Avatar
That is fantastic! Looks like a stretched version as well. A 12 window single prop. And in the 6th picture is the edge of the lift fan. The blade angle looks less than my 45 degrees. Interesting!
Last edited by ChrisCurry; May 03, 2012 at 10:04 AM.
May 08, 2012, 10:31 AM
Registered User
Anymore model pics to share guys ??


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product EAGLE N6 Multicopter Controller bdpowers Multirotor Drone Talk 282 Jan 05, 2014 07:19 PM
Discussion Eagle N6 Controller board ferrocium Multirotor Drone Talk 4 Jan 15, 2012 06:41 PM
Sold Airfield N6 - 6ch Tx and Rx - 2.4Ghz - $40 shipped conus h2oman Aircraft - General - Radio Equipment (FS/W) 9 Apr 20, 2011 07:57 PM
Sold Airfield N6 - 6ch Tx and Rx - $40 shipped conus h2oman Aircraft - General - Radio Equipment (FS/W) 2 Mar 09, 2011 12:08 AM
Help! airfield n6 transmitter information? devinvagt Radios 4 Jan 08, 2011 02:08 PM