Thread Tools
Old Jan 25, 2013, 03:31 AM
Jelico is offline
Find More Posts by Jelico
Registered User
Is anyone running the 16-50mm Sony lens on their NEX 5N Zenmuses? Results? good/bad?
Sign up now
to remove ads between posts
Old Jan 25, 2013, 10:49 PM
blbills is offline
Find More Posts by blbills
Registered User
Quote:
Originally Posted by UAVProducts View Post
When did you email us about the Z15g V2 board?

I have no email from you.

We have some Z15G V2 boards.

If you bought it from us I will send it to you for free for the Z15G
Nope, purchased from Empire RC as my post stated. Thanks.
Old Jan 26, 2013, 03:06 AM
zzr is offline
zzr
Find More Posts by zzr
zzr
DEAF-POWER
zzr's Avatar
I like F/1.7 or F/1.8 but Sony didn't make new lens pancake F/1.8
Anyone tried for 20mm F/1.7 Lumix G Pancake Lens?

Pre-order 20mm F/2.8 pancake
http://store.sony.com/webapp/wcs/sto...specifications
Old Jan 26, 2013, 06:57 AM
velaperamo is offline
Find More Posts by velaperamo
theflyingshoes
velaperamo's Avatar

My HDMI v1 board fails


I have many issues with the first generation of HDMI board. For example, lost of video, color banding, etc etc. Sometimes, only touching the HDMI cable works fine, but take off and then fails again... I'm concerned...
Take a look to this picture of the board.
Old Jan 26, 2013, 09:04 AM
UAVProducts is offline
Find More Posts by UAVProducts
Registered User
Quote:
Originally Posted by blbills View Post
Nope, purchased from Empire RC as my post stated. Thanks.
Well a new board is on its way to you from us.
Old Jan 26, 2013, 11:46 AM
sidneyw is offline
Find More Posts by sidneyw
Registered User
Got the words from my good 'source"; Zenmuse GoPro will be ready in March. I will update pricing and specs after Chinese New Year........
It will be two versions; 2-axis and 3-axis. Likely both WKM and Naza controller will support both versions.
Site Sponsor
Last edited by sidneyw; Jan 26, 2013 at 11:55 AM.
Old Jan 26, 2013, 12:29 PM
Chilli Paste is offline
Find More Posts by Chilli Paste
Registered User
Quote:
Originally Posted by velaperamo View Post
I have many issues with the first generation of HDMI board. For example, lost of video, color banding, etc etc. Sometimes, only touching the HDMI cable works fine, but take off and then fails again... I'm concerned...
Take a look to this picture of the board.
I've also been battling since day one to get a decent video downlink. I always had it in 2 pilot config and my cameraman always complained. I could never really see what he meant. (Him flying with FatShark).
Today I re-wired for single pilot and had a monitor in front of me while flying. Video signal only comes through in erratic short bursts with long pauses in between.
Whenever I touch the HDMI connector/cable it does transmit. I could also clearly see the LED changing from flashing red to solid green once I touched the cable.

What could it be? The cable with a intermittent fault? Bad shielding? The HDMI socket on camera? The converter board? ( I have V1) or even perhaps the zenmuse itself (cabling/brushes to the GCU)? Or is it a common problem on V1 board????

Any ideas and help much appreciated.

If only there were spares readily available in this country
Old Jan 26, 2013, 12:41 PM
quadslo is offline
Find More Posts by quadslo
Registered User
I also have problems with HDMI cable. I have to twist it in different directions to get a signal. And than it works ok. But it was working without a glitch when new.

My bigger problem is roll drift. Sometimes event unexpected pan drift. I really don't know what to do. Is there a problem in radio setup or WKM, compass?
I will go one firmware back. I hope it helps.
Old Jan 26, 2013, 01:11 PM
Chilli Paste is offline
Find More Posts by Chilli Paste
Registered User
@quadslo Do you also still have V1 HDMI board?

If the roll drift (I have it also) is due to compass? Who knows. I'll find out once I get a new one (still not having a proper one since the FOD firmware bug)
Old Jan 26, 2013, 01:16 PM
quadslo is offline
Find More Posts by quadslo
Registered User
I have V1 board and GH2 version. I think the problem is with the connector at the camera. Bad contact of one or more wires.
Old Jan 26, 2013, 01:16 PM
BorisSA is offline
Find More Posts by BorisSA
Registered User
Quote:
Originally Posted by sidneyw View Post
Got the words from my good 'source"; Zenmuse GoPro will be ready in March. I will update pricing and specs after Chinese New Year........
It will be two versions; 2-axis and 3-axis. Likely both WKM and Naza controller will support both versions.
ah great, hope price wise it not going to be a shock

Any pre infos if the hero 3 will be supported from beginning on ?

Thanks

Boris
Old Jan 26, 2013, 01:22 PM
Chilli Paste is offline
Find More Posts by Chilli Paste
Registered User
Thanks quadslo
Old Jan 26, 2013, 03:06 PM
mitmit is offline
Find More Posts by mitmit
Registered User
Quote:
Originally Posted by sidneyw View Post
Got the words from my good 'source"; Zenmuse GoPro will be ready in March. I will update pricing and specs after Chinese New Year........
It will be two versions; 2-axis and 3-axis. Likely both WKM and Naza controller will support both versions.
behind the times?
Autoquad Alexmos gimbal test (2 min 36 sec)

AlexMos Simple BGC (3 min 42 sec)





And I suppose soon we could see one with encoders which will be even better..
Last edited by mitmit; Jan 26, 2013 at 03:42 PM.
Old Jan 26, 2013, 03:15 PM
sidneyw is offline
Find More Posts by sidneyw
Registered User
Quote:
Originally Posted by BorisSA View Post
ah great, hope price wise it not going to be a shock

Any pre infos if the hero 3 will be supported from beginning on ?

Thanks

Boris
Hi Boris, it will be.
I am sure I will skype call you when it is available, get your credit card ready.
Site Sponsor
Old Jan 26, 2013, 03:21 PM
Sid3ways is offline
Find More Posts by Sid3ways
DJI Supporter
Sid3ways's Avatar
Quote:
Originally Posted by sidneyw View Post
Hi Boris, it will be.
It will be a price shock, or it will support the GP3?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion DJI F550 Hex Build, with 2-axis NEX-5N/GH2 Gimbal... GGoodrum Multirotor Talk 9560 May 28, 2014 12:06 AM
New Product CLD 2/3-Axis FPV Gimbal for mini cameras and GoPro crd FPV Talk 9 Jul 13, 2012 11:42 PM
Discussion DJI Spread Wings S800 and Zenmuse Z15 prices are out! tpnitro Multirotor Talk 120 Jun 19, 2012 02:27 AM
Wanted 3 axis gimbal on a budget =) Vyas FPV Equipment (FS/W) 3 Mar 20, 2012 11:57 AM
New Product CLD 2/3-Axis FPV Gimbal for mini cameras and GoPro crd Aerial Photography 2 Sep 12, 2011 07:44 PM