Walkera DEVO 10 - Page 17 - RC Groups
Thread Tools
Oct 07, 2012, 10:28 AM
RC Reviews & Tx Setup Guides
Tom Z's Avatar
Quote:
Originally Posted by jastt
my new devo 10 is turning out to be a piece of junk..i new i should of bought spektrum. it works with phoenix rc but thats about it, my esc won't recognize the throttle stick but my servo tester has no problems, and now Dfuse tools won't recognize the tx because walkera usb driver sucks.
You must manually install the USB driver.

The DfuSe USB Upgrade software also contains the driver.
The driver files are located in the “Driver” folder in your installed path
(C:\Program files\devention Upgrade Tools).

In the DfuSe USB Upgrade user manual v1.4 see the section
"6.2 Hardware installation section" on page 11/20.
This will show you how to load the driver so you can do the update.



https://www.rcgroups.com/forums/show...1&postcount=31



Tom
Last edited by Tom Z; Jul 10, 2013 at 09:06 AM.
Sign up now
to remove ads between posts
Oct 07, 2012, 10:38 AM
Registered User
thanks for quick reply, the usb cable was not all the way in the tx i had to force it in like something was going break.
Oct 07, 2012, 10:40 AM
RC Reviews & Tx Setup Guides
Tom Z's Avatar
Your welcome. I'm glad you got it working.

Tom
Oct 07, 2012, 10:45 AM
Registered User
any idea's why my tx throttle isn't recognizing a 40a turnigy plush esc, iv'e tried everything even rollback tx to older software, ive tried doing this,
deactivate throttle hold
end points to max
reverse servo
created new model name
connect battery at 100% and 0% throttle
i get the 3 beeps when connect battery and thats it.
Oct 07, 2012, 11:31 AM
Registered User
i also have fixed id enabled, so tx on then rx.
Oct 07, 2012, 11:58 AM
Heli collector
livonia bob's Avatar
Quote:
Originally Posted by jastt
thanks for quick reply, the usb cable was not all the way in the tx i had to force it in like something was going break.
You have to pull the rubber flap out of the way other wise it stops the cable from going in all the way.. I had this problem also till I figured out that the flap can be pulled out a hair more and it then doesn't interfere.

Open flap than pull gently on it and you will feel it come out a little more and clear the hole for the plug..
Oct 07, 2012, 12:23 PM
Registered User
i was aware off the rubber usb cover and there was no binding on it when plugging in, there was alot of plastic creaking when it did go in.
Oct 07, 2012, 01:31 PM
RC Reviews & Tx Setup Guides
Tom Z's Avatar
Quote:
Originally Posted by jastt
any idea's why my tx throttle isn't recognizing a 40a turnigy plush esc, iv'e tried everything even rollback tx to older software, ive tried doing this,
deactivate throttle hold
end points to max
reverse servo
created new model name
connect battery at 100% and 0% throttle
i get the 3 beeps when connect battery and thats it.

I am not sure. What receiver are you using?


Tom
Oct 07, 2012, 02:09 PM
Registered User
Quote:
Originally Posted by jastt
my new devo 10 is turning out to be a piece of junk..i new i should of bought spektrum. it works with phoenix rc but thats about it, my esc won't recognize the throttle stick but my servo tester has no problems, and now Dfuse tools won't recognize the tx because walkera usb driver sucks.
yeah, knowing which receiver would help....also you could try setting your throttle travels a little higher on either end. Oh yeah, go to the channel monitor screen and make sure you are getting proper throttle range. **Make sure it's linear**

Also, the Devo10 is really good...once you get things sorted out you're going to be quite happy with your purchase.
Oct 07, 2012, 08:59 PM
Registered User
using rx1002 and it has binded as the blue light is not flashing, i did check monitor screen and at 100% it travels to its correct position, then i set travel adjustment to 150% and it reaches full end travel, also all 4 servo's work when connected.
the first new devo 10 i received from hobbyhot had a broken gear switch as the tx was only covered in bubble wrap, they did pay for return postage. the second one i received from myrchobby the right stick got stuck after 20min use..it was fixed by taking back cover off to free up the binding, so that has added to the frustration.
with the servo tester its working good with esc+motor+rx, but when the rx is connected to tx i just get 3 beeps when battery connected.
Oct 08, 2012, 12:15 AM
Registered User
i have a good idea what the problem is, but won't know till later on.
Oct 08, 2012, 03:19 AM
Registered User
problem solved it was wrong plug placement, devo 10 is good.
Oct 11, 2012, 08:11 AM
Registered User
when i plug in a gy650 gyro into a rx1002/devo 10 the rx doesn't bind with the tx, but when i take out the gyro's channel/gain leads it binds...any ideas
Oct 11, 2012, 08:48 AM
Registered User
all good, it was a setting with tx.
Oct 12, 2012, 07:55 AM
Registered User
Hi,

I have a 3 cell lipo on my TX, and I can't seem to get the lipo alarm to go above 10v, should be 11.1 min really, is there anyway to alter this on the Devo 10?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Walkera New Devention Devo 12 transmitter first impression: ehirobo Radios 568 Oct 11, 2017 03:47 PM
Discussion Walkera Devo 12 (11X clone) Nuremberg 2011 Mikarro Radios 8 Aug 25, 2013 09:22 PM
Discussion Walkera devo reciever question? autowarrior Beginner Training Area (Heli-Electric) 0 Feb 29, 2012 12:58 AM
For Sale Walkera Devo 7 TX/Devo RX2625H Combo for sale Tom Z Aircraft - General - Radio Equipment (FS/W) 0 Oct 06, 2011 01:33 PM
For Sale Walkera Devo 7 TX/Devo RX2625H Combo for sale Tom Z Aircraft - Electric - Helis (FS/W) 0 Oct 05, 2011 12:38 PM