Shop our Airplanes Products Drone Products Sales
Thread Tools
Feb 27, 2012, 10:38 AM
Registered User
Discussion

Best method to charge a 1600 NiMh flatpack?


What is the recommended method for charging a replacement 1600 NiMh flatpack that I just bought for my glider? I have a Hyperion programmable charger that can charge and balance all types of batteries. Should I use that?
Sign up now
to remove ads between posts
Feb 27, 2012, 03:03 PM
Registered User
Rio,

I'm no expert on batteries, but these new programmable chargers make me feel like a wizard! I'd say, get out your Hyperion instructions and check it out. I use my old Multiplex charger on LiPos, NiCads, and NiMH without any issues. Just follow instructions and you'll be fine.

Dave
Feb 27, 2012, 03:37 PM
LSF303-AMA Fellow
tkallev's Avatar
For at least the first charge, charge at 1/10 C (160 ma in this case) for a minimum of 18 hours (24 hours is better).

I have seen many people fast charge NiMh cells the first time and they do not charge to the full capacity.

Using a forming charger is also a good idea if you have one, but the old 24 hour 1/10C is still the ticket for nickel chemistry cells.
Feb 27, 2012, 05:17 PM
Registered User
Lenny970's Avatar
Quote:
Originally Posted by tkallev View Post
For at least the first charge, charge at 1/10 C (160 ma in this case) for a minimum of 18 hours (24 hours is better).

I have seen many people fast charge NiMh cells the first time and they do not charge to the full capacity.

Using a forming charger is also a good idea if you have one, but the old 24 hour 1/10C is still the ticket for nickel chemistry cells.
Agreed! And after that first forming charge, I would run several charge/discharge cycles to make sure you're getting close to the labeled capacity.
Then you can safely fly the pack.

Lenny
Feb 28, 2012, 09:20 PM
St. Louis
Foambird's Avatar
We all agree here.

A characteristic to be aware of with NiMh batteries is the possibility of a "false peak" meaning the batteries fool the charger that they are fully charged before they are because the voltage rises very quickly in the early charge cycle.

The better chargers ignore this or allow you to program a time-frame to ignore this spike and keep charging.

With a less sophisticated charger (like the home wall charger supplied for consumer batteries) or to double check your charger...once "charged" I wait a 1/2 hour and put them back on charge. Not once has the charger not continued to charge for up to a half hour.

I use NiMh in my transmitters and always charge twice and I have a nice charger that is supposed to take care of business with NiMh.
Feb 29, 2012, 08:46 AM
Registered User
Andy W's Avatar
24hrs assumes the pack is empty. You can still damage cells @ 1/10C charge rate, especially when you get up to higher capacity like these.
..a


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Is Paypal the best Payment Method ??? composites Other Websites 18 Feb 22, 2012 09:00 PM
Discussion Best method for hooking up linear servos rcjim11 Indoor Pattern/F3P 7 Oct 22, 2011 11:39 AM
Discussion Best method... kerrycorcoran Foamies (Scratchbuilt) 17 Sep 30, 2011 03:14 PM
Question Spektrum DX6i + 4cell AA flatpack charge? rebeltrousers Batteries and Chargers 6 May 06, 2009 01:37 PM
For 9.6V 1600ma NIMH battary what is the best charge rate and charge time?(more) clchen Parkflyers 1 May 06, 2001 04:23 AM