Hobbyking SLICK 3D 1.3M Really Official Build Thread - Page 316 - RC Groups
Thread Tools
Dec 05, 2012, 10:47 PM
Micro Boat Forum Founder
boredom.is.me's Avatar
Does anyone know of a suitable replacement to the landing gear? I really like the aluminum gear, but it's bent beyond what I can "unbend". I wouldn't mind having a set or two laying around.
Sign up now
to remove ads between posts
Dec 06, 2012, 12:14 AM
how'd I do that....oh
chop stiX's Avatar
Quote:
Originally Posted by furballll
chop what radio did you fry and how exactly?
Sanwa RD8000 with Corona 2.4 Module
it's easy,over eagerness and impatience....
I went for a fly at the school close to my house on Mondy arvie after work with my addy,bout 3*4 through my 1st flight,my TX started beeping for low battery(I run a 2500maH 3s Zippy lipo)so had the idea to stick the lipo out my 2610 in it just so I could carry on flying.Thought I checked the connectors were the rifgt way,but the polarities are obviously reversed....and poof
I've sent it in to the JR agent here in SA,Fortunately he's close to me and I've known him for years,so waiting to hear if he can repair it.I've been fortunate that a mate helped me out with a DX7 for very cheap.almost a steal.so just need to get a few RX's and then I can start over.Anyone using orange RX's?so many mixed reports.
I just want to get 2 RX's this week so I can fly Slickerooo and mu BFU the wkd.
yes please say it....I D I OT !!!!!
Dec 06, 2012, 12:15 AM
how'd I do that....oh
chop stiX's Avatar
Quote:
Originally Posted by boredom.is.me
Does anyone know of a suitable replacement to the landing gear? I really like the aluminum gear, but it's bent beyond what I can "unbend". I wouldn't mind having a set or two laying around.
I have a solution.Land softer hehehe
Dec 06, 2012, 01:13 AM
how'd I do that....oh
chop stiX's Avatar
Nice sharkforce.
are you going to do the rudder mod?
Dec 06, 2012, 01:18 AM
fly the best
maybe. I'm not sure how to install & build it though. is it just a larger rudder that needs to be cut out, glued together and covered? what supplies are needed to complete that rudder design?
Dec 06, 2012, 01:24 AM
how'd I do that....oh
chop stiX's Avatar
Quote:
Originally Posted by sharkforce
maybe. I'm not sure how to install & build it though. is it just a larger rudder that needs to be cut out, glued together and covered? what supplies are needed to complete that rudder design?
Here are the plane Steve aka jetplaneflier so kindly made for us.you'll need balsa some ply and CA and epoxy and some covering ofcourse.
be sure to print the plan at 100% it fit on an A3
Dec 06, 2012, 05:28 AM
Grumpy old git.. Who me?
JetPlaneFlyer's Avatar
If you do build the rudder best to use the latest version of the drawing which has a few small improvements based on findings during building:

New drawings were posted a few pages back: https://www.rcgroups.com/forums/show...postcount=4481
Dec 10, 2012, 04:43 AM
3D apprentice
Hoverin's Avatar
Hey all, just got back from my second outing with the Slick. Unfortunately sourcing a videographer has alluded me thus far...
The first outing was a nervous trim n setup but the second was a relaxed awesome fly and I have total confidence in it.
I was harriering low n slow with absolute confidence, turning etc. The only time a wing even looked like dropping was because of my heavy rudder thumb. I can't compare the old rudder to the new coz I never flew with it, but this plane is 100 times better flyer than anything I have (not that I have anything to write home about). Thanks Steve for the rudder and I'm looking at a reserve airframe
Last edited by Hoverin; Dec 12, 2012 at 12:07 AM.
Dec 10, 2012, 11:31 AM
fly low, fly fast, fly 3d
nathan100's Avatar
Quote:
Originally Posted by chop stiX
Sanwa RD8000 with Corona 2.4 Module
it's easy,over eagerness and impatience....
I went for a fly at the school close to my house on Mondy arvie after work with my addy,bout 3*4 through my 1st flight,my TX started beeping for low battery(I run a 2500maH 3s Zippy lipo)so had the idea to stick the lipo out my 2610 in it just so I could carry on flying.Thought I checked the connectors were the rifgt way,but the polarities are obviously reversed....and poof
I've sent it in to the JR agent here in SA,Fortunately he's close to me and I've known him for years,so waiting to hear if he can repair it.I've been fortunate that a mate helped me out with a DX7 for very cheap.almost a steal.so just need to get a few RX's and then I can start over.Anyone using orange RX's?so many mixed reports.
I just want to get 2 RX's this week so I can fly Slickerooo and mu BFU the wkd.
yes please say it....I D I OT !!!!!
i run orange rx's in my ef extra they have work perfectly
Dec 10, 2012, 11:51 AM
Santi
DaaBears's Avatar
Quote:
Originally Posted by chop stiX
Sanwa RD8000 with Corona 2.4 Module
it's easy,over eagerness and impatience....
I went for a fly at the school close to my house on Mondy arvie after work with my addy,bout 3*4 through my 1st flight,my TX started beeping for low battery(I run a 2500maH 3s Zippy lipo)so had the idea to stick the lipo out my 2610 in it just so I could carry on flying.Thought I checked the connectors were the rifgt way,but the polarities are obviously reversed....and poof
I've sent it in to the JR agent here in SA,Fortunately he's close to me and I've known him for years,so waiting to hear if he can repair it.I've been fortunate that a mate helped me out with a DX7 for very cheap.almost a steal.so just need to get a few RX's and then I can start over.Anyone using orange RX's?so many mixed reports.
I just want to get 2 RX's this week so I can fly Slickerooo and mu BFU the wkd.
yes please say it....I D I OT !!!!!
I used the orange rx's on small foamy's with no issues, however, like all cheap products, I shy away from using them in anything I care about... I've seen many that work perfectly, and a few that have failed. When it comes to servos and rx's, I don't take any shortcuts. You should be fine using one though.
Dec 10, 2012, 02:30 PM
Grumpy old git.. Who me?
JetPlaneFlyer's Avatar
Quote:
Originally Posted by Hoverin
Hey all, just got back from my second outing with the Slick. Unfortunately sourcing a videographer has alluded me thus far...
The first outing was a nervous trim n setup but the second was a relaxed awesome fly and I have total confidence in it.
Great that it's flying well. I had mine out again this week and I'm now sure that the big rudder has no adverse effects at all. First time I tried the big rudder my pop-tops were poor but that was just my timing, they were fine this time.
For a plane with no SFG's the HK slick is great in KE. Say it in hushed tones but IMHO it's actually better than the AJ Slick in KE. The AJ will snap out of KE if you apply too much rudder, the HK Slick is more predictable, KE loops are a breeze.
Dec 10, 2012, 05:38 PM
Registered User
Beancounter's Avatar
Anybody have any know how if this slick is as good as the HK one?

http://www.valuehobby.com/57in-elect...dy-to-fly.html
Dec 10, 2012, 05:47 PM
"Get off the runway!"
Da Big_G's Avatar
Quote:
Originally Posted by Beancounter
Anybody have any know how if this slick is as good as the HK one?

http://www.valuehobby.com/57in-elect...dy-to-fly.html
Good price and has air-foiled tail feathers.......8 inch bigger wingspan. For less money.
If it can be kept at 5 lbs., it should fly well. This should be interesting..
Last edited by Da Big_G; Dec 10, 2012 at 07:54 PM.
Dec 12, 2012, 12:23 AM
3D apprentice
Hoverin's Avatar
Quote:
Originally Posted by UCDme3D
I used the orange rx's on small foamy's with no issues, however, like all cheap products, I shy away from using them in anything I care about... I've seen many that work perfectly, and a few that have failed. When it comes to servos and rx's, I don't take any shortcuts. You should be fine using one though.
I'm exactly the same UC, although I'm slowly moving closer to trusting them. It would be a very interesting read (maybe already out) of a decent controlled unbiased test between the 2 as I can't help wondering if the "fails" from the oranges wouldn't of happened with the real deal (barring internal failure of course),
as I haven't seen much of that from Spektrum, except the AR500 thing a couple years back...

Quote:
Originally Posted by JetPlaneFlyer
Great that it's flying well. I had mine out again this week and I'm now sure that the big rudder has no adverse effects at all. First time I tried the big rudder my pop-tops were poor but that was just my timing, they were fine this time.
For a plane with no SFG's the HK slick is great in KE. Say it in hushed tones but IMHO it's actually better than the AJ Slick in KE. The AJ will snap out of KE if you apply too much rudder, the HK Slick is more predictable, KE loops are a breeze.
Agreed, this plane loves KE, I even managed to start my KE mixing last outing, (only have 3 batteries for it ATM, on the X-mas list) in fact until you get into the higher alpha KE the coupling is almost non-existent, I nearly wasn't going to worry about it... All this with a slight warp in the badly made rudder of mine...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Turnigy SLICK 3D 1.3M -HOBBYKING Official Build Thread will3d4food 3D Flying 1979 Aug 17, 2017 05:50 PM
Discussion Official Hobbyking 720p HD Camera Thread jaskel FPV Equipment 541 Dec 07, 2016 05:16 PM
Build Log The Official Raven 3M build thread has begun. Windependence Sailplane Talk 1561 Aug 26, 2016 02:45 PM
Discussion Official-Twisted Hobbys Extra Slick 32" Slickinsaneness Build/Fly Thread Tom K. 3D Foamies 1377 Apr 06, 2016 07:24 AM
New Product HK DuraFly Micro Slick 360 2S - Official Thread will3d4food Scratchbuilt Indoor and Micro Models 879 Feb 28, 2015 12:14 PM