Mar 08, 2012, 12:20 PM
Once u go yak u never go back
marksextra's Avatar
Quote:
Originally Posted by 6L6Amp View Post
You'd only need to use a 3s pack into the BEC Pro if you are running HV servos. .
Quote:
Originally Posted by heritageflyer View Post
Are 7955TG's considered HV?
Quote:
Originally Posted by 6L6Amp View Post
They can be run on 2s unregulated.
This brings up a question for me.

I've never really heard of running 3S. What are the rules or reasons for 3S vs 2S?
Sign up now
to remove ads between posts
Mar 08, 2012, 12:29 PM
3DHS 'native'
going4speed's Avatar
Higher voltages just make the BEC work harder. It now has to drop 11.1v nom to 6-7.4 instead of 7.4v nom to 6v etc.

Quote:
Originally Posted by marksextra View Post
This brings up a question for me.

I've never really heard of running 3S. What are the rules or reasons for 3S vs 2S?
Mar 08, 2012, 12:47 PM
Once u go yak u never go back
marksextra's Avatar
Quote:
Originally Posted by going4speed View Post
Higher voltages just make the BEC work harder. It now has to drop 11.1v nom to 6-7.4 instead of 7.4v nom to 6v etc.
if you even have a bec. And the 3S advantage is....?
Mar 08, 2012, 12:49 PM
Registered User
jsmith285's Avatar
Quote:
Originally Posted by marksextra View Post
if you even have a bec. And the 3S advantage is....?
A Constant 8v throughout the whole flight.
Mar 08, 2012, 12:50 PM
customstandoffs
cmala's Avatar
If you run 3S to your BEC then you can regulate the voltage at 8 volts, or around there and have a consistant high voltage running your servos for the entire flight.

If you run straight 2S LiPo, you are at 8.4v at the start of the flight and at something lower at the end of the flight. If you are good enough (I'm not) you will notice a servo speed/torque change during the flight as the voltage gradually decreases.
Mar 08, 2012, 01:03 PM
Once u go yak u never go back
marksextra's Avatar
ok. and the ways to regulate 3S to a constant 8V are? Yes. I'm still asking this after I just bought 2 2S2200 for my 89 slick.
Mar 08, 2012, 01:07 PM
Registered User
6L6Amp's Avatar
Quote:
Originally Posted by marksextra View Post
ok. and the ways to regulate 3S to a constant 8V are? Yes. I'm still asking this after I just bought 2 2S2200 for my 89 slick.
Use a 3s pack (12.6 volts) and a BEC. Set the BEC to 8.4 volts.
Mar 08, 2012, 01:08 PM
customstandoffs
cmala's Avatar
The easiest way would be to use a Castle BEC Pro

You can purchase a different brand of voltage regulator from Fromeco or Smart Fly or other places

I'm running two 2S LiPos unregulated in my 103 Extra. I may, sometime in the future change over to 3S regulated but I don't have any desire to do so at the current time.

2S LiPo unregulated has worked well for me
Mar 08, 2012, 01:11 PM
Registered User
jsmith285's Avatar
Quote:
Originally Posted by marksextra View Post
ok. and the ways to regulate 3S to a constant 8V are? Yes. I'm still asking this after I just bought 2 2S2200 for my 89 slick.
Use what you bought. When you start your next build, ask what we are doing now. Because it changes frequently.
Mar 08, 2012, 01:12 PM
Once u go yak u never go back
marksextra's Avatar
Quote:
Originally Posted by cmala View Post
The easiest way would be to use a Castle BEC Pro

You can purchase a different brand of voltage regulator from Fromeco or Smart Fly or other places

I'm running two 2S LiPos unregulated in my 103 Extra. I may, sometime in the future change over to 3S regulated but I don't have any desire to do so at the current time.

2S LiPo unregulated has worked well for me
That's what I've always run, but with me switching to all HV servos and RX I was just wondering what the advantages were. All good stuff. Thanks
Mar 08, 2012, 01:30 PM
Stick banger
Ace4's Avatar
Quote:
Originally Posted by marksextra View Post
This brings up a question for me.

I've never really heard of running 3S. What are the rules or reasons for 3S vs 2S?
Regulated 2s would max out around 6.5V, most regulators cannot regulate down to the same voltage as the supply, since the 2s voltage will drop under load. Running a 3s through a BEC lets you regulate to 7.4V or 8.4V. Be careful though, some switches and things are only rated to 10V, so you can't use them with the 3s pack. I initially thought about running two 3s packs into my Wolverine switch, then putting a BEC on the output so I could regulate at 8.4V, however the Wolverine unit is only rated to 12V (I guess I should've called Fromeco to find out if it can handle 12.6V).
Mar 08, 2012, 01:44 PM
ICU
ICU
Check out my Shapeways Shop
ICU's Avatar
Hi all,

I've got a few questions for you all and this seems like an appropriate place for them.

I only have one balsa plane. The 3DHS 41" edge, and love it! I've been thinking about getting another 3DHS plane.

Right now I'm undecided between the 48" Velox (found one RTF for 300 on craigslist) or the 51" Slick. I'm leaning more towards the Slick, but I do not like the color scheme. I know I could just have it recovered, but I've never covered a plane before and I'm sure it's not cheap to have someone do it.

Is there anyone out there that has both of these planes? Which would you recommend? I'm looking for more of a 3D performance vs standard aerobatics.

Also I saw on 3DHS's website in the "got eta" and there is a 48" plane on the water. What is this going to be? Anyone know?


Thanks
Mar 08, 2012, 01:56 PM
Registered User
FireyFate's Avatar
Quote:
Originally Posted by ICU View Post
Also I saw on 3DHS's website in the "got eta" and there is a 48" plane on the water. What is this going to be? Anyone know?
That's the 48" EPP Yak. It apparently was left up there to cause confusion
Mar 08, 2012, 01:58 PM
Registered User
SnowDog1974's Avatar
Quote:
Originally Posted by ICU View Post
Hi all,

I've got a few questions for you all and this seems like an appropriate place for them.

I only have one balsa plane. The 3DHS 41" edge, and love it! I've been thinking about getting another 3DHS plane.

Right now I'm undecided between the 48" Velox (found one RTF for 300 on craigslist) or the 51" Slick. I'm leaning more towards the Slick, but I do not like the color scheme. I know I could just have it recovered, but I've never covered a plane before and I'm sure it's not cheap to have someone do it.

Is there anyone out there that has both of these planes? Which would you recommend? I'm looking for more of a 3D performance vs standard aerobatics.

Also I saw on 3DHS's website in the "got eta" and there is a 48" plane on the water. What is this going to be? Anyone know?


Thanks
If you like the color scheme of the Velox and you don't like the color scheme of the Slick (?) then get the Velox. Both are good 3D machines....all 3DHS planes are good 3D machines! so the choice is really up to you.
Mar 08, 2012, 01:58 PM
Registered User
shadow102's Avatar
ETA page needs updating, it was the 48" EPP yak.

Me personally i would go with the slick if you can afford it just due to the size and bigger is better pretty much...i wouldnt worry about the covering though seems like alot of money to dump into an ARF. The Velox is a nice plane though as well and that $300 might be a good deal all depends on the equipment in it.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Unofficial NQD Tear Into Jet Boat Mod Thread Energy Jet Drive Boats 15370 Mar 21, 2017 10:43 PM
Discussion The Official AirWare Q&A Thread AndyKunz Radios 104 Dec 29, 2016 05:18 PM
Discussion Banana Hobby Customer Support Request/Q and A Thread! banana hobby Banana Hobby 1174 Dec 27, 2016 07:51 PM
Discussion THE FIRST UNOFFICIAL Parkzone Sukhoi mods thread!!!! bluemeane Micro Ready-to-Fly 27 Aug 17, 2009 11:23 PM
Megatech H2O unofficial thread and first rewiew. grk65 Racing Boats - Electric 7 Mar 05, 2007 12:09 AM