|
|
|
I ordered some new antennas and will give them a try. I have seen reports of 11 km range with these antennas on receiver and a 7 db patch antenna on tx.
|
|
|
|
|
|
|
Aurora 9x with 5ch receiver, ppm questions
Basically I want to bind this receiver to my tx and use the ppm feature to connect it to a micro quad alienwii control board, now I'm new to ppm do what do I new to do? Is the urora 9x ppm compatable? Does it matter as the receiver connects to the board via ppm? Please help ! Love what your doing Simon but I need some advice!!
|
|
|
|
|
|
I believe the 9X does not have ppm, the 9 does.
|
|
|
|
|
|
You must be kidding i don't know any tx released after 2010 that will not have ppm on the tx.
However Ppm on the rx is independent from the TX, and it will be there on Simon's receiver, but not on original hitec one. |
|
|
|
|
|
So in the one you own, you've already gone inside and found ppm source? Technical specs on the 9X has no info on ppm.
|
|
|
|
||
|
Quote:
About any tx on the market uses PPM between trainer and master tx, except few which are using Wifi or proprietary protocols. Also check this link, Alan always has answer for everything that has Hitec inscription on it: https://www.rcgroups.com/forums/show...39&postcount=1 |
|
|
||
|
|
|
Is it possible to flash these RXs back to FrSky?
Hi,
I have 3 of these Hitec minima compatible receivers. Two 4 channels and one 5 channel. They have been great on my Aurora 9. However, I have now moved to a Taranis and would like to know if it is possible to re-purpose the receivers back to the FrSky system. If so, what would I need? I tried to sell them locally here in New Zealand but there does not seem to be much interest. Thanks. |
|
|
|
|
|
Put the Hitec 2.4 JR-fit module in the back of the Taranis.
|
|
|
|
|
|
What does red and green fast blinking lights mean??
|
|
|
|
|
|
|
|
|
|
|
|
Frysky? |
|
|
|
|
|
According to the Minima instructions:
With the Link button pressed, power up the receiver. Both RED and BLUE LEDs will blink rapidly to find the transmitter signal. Release the link button when the RED LED on the receiver glows steady |
|
|
|
|
|
Wrong receiver
I think that's the larger 6 channel. This is the little one where you have to jump pin one and five to bind. After I put power to receiver instantly I get red and green flashing lights instead of green. It will connect to my optima receiver though.
|
|
|
|
||
|
Got it to bind sort ofQuote:
Update plugged speed controller into channel 5 and it bound but I do not have throttle since that is channel 3.. all other channels work. Do I need some sort of splitter? Kind of stupid to me whole point is to be light??? |
|
|
Last edited by onesillyhatch; Aug 10, 2017 at 01:48 PM.
|
|
|
||
|
Quote:
If you use something different than the Aurora, as simple mix should sort it out. You can't do anything with a splitter / y-cable. |
|
|
||
Thread Tools | |
Similar Threads | |||||
Category | Thread | Thread Starter | Forum | Replies | Last Post |
Question | Hitec 2.4GHz compatible receivers | G_Wright | Radios | 1 | May 09, 2011 06:02 PM |
Sold | OrangeRX Orange RX Spektrum 2.4GHz DSM2/X compatible receiver | lrplin | Aircraft - General - Radio Equipment (FS/W) | 2 | Apr 18, 2011 12:07 PM |
Discussion | OrangeRx Futaba FASST Compatible 8Ch 2.4Ghz Receiver | WSWitby | Electric Plane Talk | 2 | Apr 05, 2011 07:30 AM |
Sold | OrangeRX Orange RX Spektrum 2.4GHz DSM2/X compatible receiver | lrplin | Aircraft - General - Radio Equipment (FS/W) | 5 | Mar 30, 2011 05:35 PM |
Sold | OrangeRX Orange RX Spektrum 2.4GHz DSM2/X compatible receiver | lrplin | Aircraft - General - Radio Equipment (FS/W) | 0 | Mar 28, 2011 03:38 PM |