New Products Flash Sale
Thread Tools
Old Jan 04, 2013, 10:50 AM
jrb is offline
jrb
Find More Posts by jrb
jrb
Member
jrb's Avatar
What the easiest/best way to get my 30+ models from my 9503 (I have PropoData) to a DX18?
Sign up now
to remove ads between posts
Old Jan 04, 2013, 10:53 AM
ghoffman is offline
Find More Posts by ghoffman
Registered User
Quote:
Originally Posted by jrb View Post
What the easiest/best way to get my 30+ models from my 9503 (I have PropoData) to a DX18?
I am all ears on this one!
Old Jan 04, 2013, 10:57 AM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
Quote:
Originally Posted by jrb View Post
What the easiest/best way to get my 30+ models from my 9503 (I have PropoData) to a DX18?
You take the models you are going to be flying first or sooner and transfer them manualy, then later when you have time you transfer the others.

Programming your new radio will have a positive affect, you will learn more about it.
Old Jan 04, 2013, 11:05 AM
Fig Jam is offline
Find More Posts by Fig Jam
I am UNIQUE!
Fig Jam's Avatar
Quote:
Originally Posted by struggleforlife View Post
Any news on the new DX18 yet (with audio telemetry, bigger screen and USB)?
Yeah, it's called a Futaba 18MZ.

Mike
Old Jan 04, 2013, 11:08 AM
JohnathanSwift is offline
Find More Posts by JohnathanSwift
Suspended Account
Quote:
Originally Posted by Fig Jam View Post
Yeah, it's called a Futaba 18MZ.

Mike
Please substitute "Fuh, Tah, Bah," for "badges:"

We don't need no stinking badges! (0 min 15 sec)


Old Jan 04, 2013, 12:13 PM
jrb is offline
jrb
Find More Posts by jrb
jrb
Member
jrb's Avatar
Wasn't a big deal from 652 to 8103; to 9303 a good bit of an effort.

Duck soup to 9503!

A PC tool sure would be helpful.
Old Jan 04, 2013, 12:56 PM
Steam28 is offline
Find More Posts by Steam28
Registered User
Steam28's Avatar
Balancing multiple servos on a single control surface using the DX18. After reviewing the tutorial video on the Spektrum website, they balance the one aileron servo on the wing surface using the procedure but at about 2:05 minutes into the video, he says that both servos are now in balance. I have not actually done this yet on a plane but does it mean that you only balance one servo with the TX and volt meter but the software knows that both servos are on a single control surface so its balancing both at the same time because they are connected within the receiver? I hope I conveyed that clearly.

Can someone please clarify the procedure and confirm that you do not have to perform this procedure for each servo on the same single surface?

Thanks.
Old Jan 04, 2013, 01:02 PM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
Not an expert but I have used it before on one setup and I only needed to balance the one servo to match the other. No need to balance the other since I just made the other one balance with that one.

Car A is on cruise control set to 100, Car B just needs to match the speed of Car A then both cars would be going the same speed. Car A does not need to be adjusted since Car B was adjusted.

Hope that makes sense.
Old Jan 04, 2013, 01:19 PM
Snowflake6515 is online now
Find More Posts by Snowflake6515
Michael

Balancing Multiple Servos


As "freechip" indicated, the first one does not have to be "balanced"; it serves as the reference.

However, all other servos, on the SAME surface, must be balanced following the video procedure. There are many schools of thought as to which servo should be the primary one (not "balanced", but serves as "reference" or "master") and which should be slaved (i.e., balanced to the master servo.) Giant scale forums have a lot of info about this, but I personally start inboard and work my way outboard following the video's procedure.

The reason there are so many opinions is because, for example, the wing flexes in flight (tip more than the inner/root sections.) So, balancing on a workbench is not the same as dynamically balanced to reflect air loads; but go to the forums for opinions...

Personally, I find that the workbench balance handles most of the needs, but I do not have telemetry to indicate the difference in the air; now there's a neat project. :-)

YMMV.

Michael
Quote:
Originally Posted by Steam28 View Post
Balancing multiple servos on a single control surface using the DX18. After reviewing the tutorial video on the Spektrum website, they balance the one aileron servo on the wing surface using the procedure but at about 2:05 minutes into the video, he says that both servos are now in balance. I have not actually done this yet on a plane but does it mean that you only balance one servo with the TX and volt meter but the software knows that both servos are on a single control surface so its balancing both at the same time because they are connected within the receiver? I hope I conveyed that clearly.

Can someone please clarify the procedure and confirm that you do not have to perform this procedure for each servo on the same single surface?

Thanks.
RCG Plus Member
Old Jan 04, 2013, 03:36 PM
PropsnWings is offline
Find More Posts by PropsnWings
Scale Aerobatic Pilot
PropsnWings's Avatar
Quote:
Originally Posted by AndyKunz View Post
He's talking about the one without gimbals. You just think what you want it to do, like Firefox.

Andy
I dont want to know where the probes go....
Old Jan 04, 2013, 03:38 PM
PropsnWings is offline
Find More Posts by PropsnWings
Scale Aerobatic Pilot
PropsnWings's Avatar
Quote:
Originally Posted by freechip View Post
you take the models you are going to be flying first or sooner and transfer them manualy, then later when you have time you transfer the others.

Programming your new radio will have a positive affect, you will learn more about it.
+1
Old Jan 04, 2013, 03:39 PM
mejmea is offline
Find More Posts by mejmea
Always trying to learn
mejmea's Avatar
Quote:
Originally Posted by PropsnWings View Post
I dont want to know where the probes go....
Why they go in different places for different users of course, at least partly dependent on the "pucker factor" you like to fly with!
Old Jan 04, 2013, 04:42 PM
AndyKunz is online now
Find More Posts by AndyKunz
AndyKunz's Avatar
Quote:
Originally Posted by PropsnWings View Post
I dont want to know where the probes go....
No probes, it has ESP!

Andy
Site Sponsor
Old Jan 04, 2013, 04:58 PM
PropsnWings is offline
Find More Posts by PropsnWings
Scale Aerobatic Pilot
PropsnWings's Avatar
Quote:
Originally Posted by AndyKunz View Post
No probes, it has ESP!

Andy
You know, someday in the not so distant future... we may all be laughing at the fact we made fun of it in this way... lol Technology always never ceases to amaze me how fast it progresses.
Old Jan 04, 2013, 05:18 PM
JohnathanSwift is offline
Find More Posts by JohnathanSwift
Suspended Account
Quote:
Originally Posted by AndyKunz View Post
No probes, it has ESP!

Andy
I hate it when the aliens do that....


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Spektrum DSM2 and the Nats - Question for Spektrum/JR users aeajr Sailplane Talk 25 May 29, 2012 04:14 PM
Sold Spektrum DX6 6-channel System with Spektrum AR6000 Receiver $50 shooboy Aircraft - General - Radio Equipment (FS/W) 6 Dec 20, 2011 06:12 PM
Sold Spektrum DX6 6-channel System with Spektrum AR6000 Receiver $50 shooboy Aircraft - General - Radio Equipment (FS/W) 4 Dec 14, 2011 08:30 PM
For Sale Spektrum & JR 2.4 Ghz DSM2 receivers for sale I have a sailplane sized Spektrum AR93 zaptherio Aircraft - General - Radio Equipment (FS/W) 1 Nov 15, 2011 06:14 PM
Sold SPEKTRUM DX6i DSMX with Spektrum Ni-cads and charger- like new condition shooboy Aircraft - General - Radio Equipment (FS/W) 6 Oct 19, 2011 05:59 AM