CopterFrames TwoDee EVO,Now Brushless Convertion Available - Page 10 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Feb 17, 2012, 03:03 AM
Registered User
Discount + discount but for what? What is the result? Can you show us a video, i believe that there is a bad weather in Turkey, but some video in front of a mirror with the gimbal in hands will be appreciated.
Sign up now
to remove ads between posts
Feb 17, 2012, 06:23 AM
Registered User
Quote:
Originally Posted by volver
Discount + discount but for what? What is the result? Can you show us a video, i believe that there is a bad weather in Turkey, but some video in front of a mirror with the gimbal in hands will be appreciated.
Post #58 has video of the gimbal being moved by hand.

Still waiting for the on board flying footage.
Feb 17, 2012, 07:32 AM
Registered User
va3mw's Avatar
Quote:
Originally Posted by ozanozkok
Thanks Mike
I hope you like it and will share your air videos.
I m updating 15mm m3 screws to 20mm .
at 22-feb,a landing gear set will be ready for your cam gimbal.please chechk it.
Best regards.
Thanks... depending on the servo you use for roll, you might have to build it a few different ways. The 'horn' that I used for the belt drum was a little thick I thought as the 15mm screws were too short and I wasn't able to use the M3 nuts on them at all, so I just used thread lock.

However, once I was done assembling, the belt was binding a little, so I need go a little longer on the screws and add a bit of a shim to give the belt some room.

I will also all about 1/2 a shim on the 3 bearing shafts just to give the camera mount a bit more room to roll. If I tighten those 3 screws then the mount will bind some.

Just some fine tuning. Not a big deal.
Feb 17, 2012, 09:41 AM
Musician-Designer
ozanozkok's Avatar
Quote:
Originally Posted by va3mw
Thanks... depending on the servo you use for roll, you might have to build it a few different ways. The 'horn' that I used for the belt drum was a little thick I thought as the 15mm screws were too short and I wasn't able to use the M3 nuts on them at all, so I just used thread lock.

However, once I was done assembling, the belt was binding a little, so I need go a little longer on the screws and add a bit of a shim to give the belt some room.

I will also all about 1/2 a shim on the 3 bearing shafts just to give the camera mount a bit more room to roll. If I tighten those 3 screws then the mount will bind some.

Just some fine tuning. Not a big deal.
Hi Mike.
On the bearing side,i ve drilled the holes at 4.9mm couse of the m3 is actually 2.85mm.please be carefull when tune the bearing shafts.if they stocks hard the lower sides edge,it will be resist to move.actually i prefer the belt tension. 0.2 mm space to lower bearing is optimum space.
Lower(middle one) bearing is not functional at static position.it will functional when the roll axis acts.
of course try your way.but be carefull the tension of the bearings.roll servo works hard and if bearings tension resist it, it can be warm.

Thanks
Feb 19, 2012, 12:28 PM
Musician-Designer
ozanozkok's Avatar
3. axis module first prototype.it is need more reduction over 1/5.
http://copterframes.blogspot.com/201...is-module.html
Feb 19, 2012, 02:12 PM
manual flying apologist
Adidas4275's Avatar
Looks good.

I think I will be buying a mount+ landing gear from you next paycheck.


Hopefully there is some onboard video by then
Feb 19, 2012, 02:29 PM
Musician-Designer
ozanozkok's Avatar
Quote:
Originally Posted by Adidas4275
Looks good.

I think I will be buying a mount+ landing gear from you next paycheck.


Hopefully there is some onboard video by then
Thank you.
I hope final version of 3.axis will be lightweighted with landinggear.i m working on the reduction gear structure now..
Feb 19, 2012, 04:25 PM
Registered User
jetbootz's Avatar
Quote:
Originally Posted by Adidas4275
Looks good.

I think I will be buying a mount+ landing gear from you next paycheck.


Hopefully there is some onboard video by then
+1

I will most likely get one next paycheck. I do however wnat to see onboard video first, please can we see some, its been ages and still no video !
Feb 19, 2012, 05:04 PM
DJI Supporter
Sid3ways's Avatar
I think some asked this before and I never saw an official response. Will this work with the DroidWorx camera mount location?
Feb 19, 2012, 05:19 PM
manual flying apologist
Adidas4275's Avatar
I asked and he said that it was not the same, but that he would make a mounting plate for it to match up with if we gave him the specs. I have not had time to measure or find the specs for him.
Feb 23, 2012, 05:07 PM
Registered User
jetbootz's Avatar
so all these testers got these last week and still no onboard video ?? anyone ?
Feb 23, 2012, 08:22 PM
Eat-Sleep-Work-Fly-Repeat
Grips's Avatar
Sent them to the wrong testers obviously. I've posted a video to my youtube count three times already this week of flying lol
Feb 25, 2012, 11:44 AM
Registered User
This tester still hasn't received his
Feb 25, 2012, 03:36 PM
Prying Open My Third Eye
slo_dave's Avatar


I'm ready to buy, just waiting on a couple good reviews.

Dave
Feb 29, 2012, 05:06 PM
Registered User
jetbootz's Avatar
Quote:
Originally Posted by slo_dave


I'm ready to buy, just waiting on a couple good reviews.

Dave
err, VIDEO ? Has anyone even received one of these yet ? I can't understand how a manufacturer can make these things, ship them and design a website, and yet not get round to actually posting even one onboard video online......? I would really like to buy one but some video would be nice first...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion A new professional camera gimbal (tongue in cheek) SeismicCWave Multirotor Drone Talk 23 Nov 13, 2011 01:48 AM
Discussion What gyros to use on a 2 Axis camera gimbal? Voguna Aerial Photography 0 Mar 13, 2011 12:51 PM