5010-14 360KV Brushless Motor - Page 7 - RC Groups
Thread Tools
Jun 28, 2012, 02:09 PM
Registered User
Quote:
Originally Posted by rimshotcopter
P.S. One of the biggest issue for me with this motor is, the shift diameter. It is only 3.17mm with a small retainer clip on the back. A motor with a longer bell, the magnetic force will keep the motor from coming apart, not true with these motors. it is very easy for the bell to come off if that clip should come free. Also the gyroscopic forces created by the large spinning prop will play havoc on the small shaft and bearings.
Yeah, that doesn't sound very good. Seems like mounting it upside down so the prop is pushing would be safer. I think I'll stick with the NX-4006... And hope that rc-timer comes out with another low kv motor like this that solves all the problems. I really like the bolt on threaded shaft adapters.
Sign up now
to remove ads between posts
Jul 02, 2012, 09:46 AM
Multicopter Nut
ThePara's Avatar
Quote:
Originally Posted by fallingdown
Neat looking quad! Got any video of it... from it?
Search for "Parathe13" on youtube.
Jul 02, 2012, 12:49 PM
Registered User
... hmm guys had plan to use some 30amp esc.. but I just noticed they are 2-4S rated..

What are you guys doing for ESC .. 5S or 6S .?
Jul 02, 2012, 01:02 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Doh...!!!
Luis you did post before.. LOL
Jul 02, 2012, 01:41 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by flyhigh300
... hmm guys had plan to use some 30amp esc.. but I just noticed they are 2-4S rated..

What are you guys doing for ESC .. 5S or 6S .?
I am using 4S and never planned on going any higher. If I am not get the thrust required with a 4S battery, Abandon this project is in the mix.

Edited: Motors are rated Battery: 2-6Li-Po
Jul 02, 2012, 01:59 PM
Registered User
yeah ..

I plan to test at 4S .. with 14in props.. first..

One thing I find is I get less flying time that what most post.

I'm at about 3400ft above sea level.. maybe more..

wanted the frame to be setup up to have that option for bigger batteries..


Quote:
Originally Posted by rimshotcopter
I am using 4S and never planned on going any higher. If I am not get the thrust required with a 4S battery, Abandon this project is in the mix.

Edited: Motors are rated Battery: 2-6Li-Po
Aug 12, 2012, 07:21 AM
Registered User
Quote:
Originally Posted by milo12
My MT4008-600 easily swings 16 inch props on 3S and 4S. I have run APC 16, the same carbon props shown above and the German carbon props by Flyduino which seem to be no longer sold.

What is the mounting bolt pattern and bolt sizes for the 5010 motor?
As I am looking for the best props for my MT4008-600 those carbon props maybe the key to success. Could you show us how did you mount those props? Right now I am running APC 14x4,7 on an octocopter on 3s. AUW is about 3300g and I am only getting 7 min flights on 5000mAh. Which props would be the best (I can upgrade to 4s)? Or should I just try to look for better and more efficient motors (maybe this 5010?)?
Aug 12, 2012, 07:30 AM
Registered User
According to the simulator, your 7 minutes are right.
15"@3s will raise a bit over 8 minutes, 14"@4s to more than 9 minutes.
Aug 12, 2012, 07:38 AM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by RENATOA
According to the simulator, your 7 minutes are right.
15"@3s will raise a bit over 8 minutes, 14"@4s to more than 9 minutes.
Question please, can you rerun this simulation using six motors verse eight? Not sure of the weight differences between the two configurations.
Aug 12, 2012, 09:19 AM
Registered User
The octo will hover at about 51% throttle, for the hexa you must raise it at 68%, for same weight. Or decrease weight a bit under 3kg.

You can play yourself, just load the page below...

http://ecalc.ch/xcoptercalc_e.htm?ec...h=4.7&blades=2

then go to motor type, switch to custom and change kv to 600. That's because his model is not in the simulator database, and this is the closest.

PS: Yes, I trust this simulator, matched everything I flown so far within the claimed 15% estimation. For hover time and Amps drawn at least.
Depending on area where you are, the page can open in imperial units, and you should switch back to metric and change weight to 3300 grams manually.
Last edited by renatoa; Aug 12, 2012 at 09:26 AM.
Aug 12, 2012, 09:24 AM
Registered User
rimshotcopter's Avatar
Thank you.
Aug 12, 2012, 12:06 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by RENATOA

You can play yourself, just load the page below...

http://ecalc.ch/xcoptercalc_e.htm?ec...h=4.7&blades=2
This is a very useful and handy tool, is there any possibility of making it into a stand-alone program or application for a smart phone or PDA?
Aug 12, 2012, 01:15 PM
Registered User
Yes, code behind is known, you need a programmer
Person, not device
Aug 12, 2012, 01:19 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by RENATOA
Yes, code behind is known, you need a programmer
Person, not device
Hmmm, I do not own a Smart Phone but a PDA and you know, Java runs on just about every platform out there today.

Make it open source and I am sure there will be many to answer the call.
Aug 12, 2012, 01:51 PM
Registered User
EddieWeeks's Avatar
Quote:
Originally Posted by Boogie3D
As I am looking for the best props for my MT4008-600 those carbon props maybe the key to success.
?
...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold EZ Flite 35 Amp Brushless Motor ESC 14.00 shipped mpotter187 Aircraft - Electric - Power Systems (FS/W) 3 Nov 03, 2011 12:58 PM
Sold CF2812-14 1534KV Outrunner Brushless Motor rcbuilder247365 Aircraft - Electric - Power Systems (FS/W) 2 Aug 07, 2011 02:32 AM
Sold bl-2208/14 1450kv brushless motor REDUCED nitrodude71 Aircraft - Electric - Power Systems (FS/W) 11 May 15, 2011 07:03 PM
FS: Used AXI 4120-14 Brushless Motor sonny89108 Aircraft - Electric - Airplanes (FS/W) 4 Nov 12, 2003 01:12 PM
FS - AXI 4120/14 Brushless motor Bill Germanson Aircraft - Electric - Airplanes (FS/W) 5 Jun 28, 2003 08:07 PM