Thread Tools
Feb 20, 2013, 06:21 PM
Pursuit of Happiness
Ron101's Avatar
I think open ducts will be fine... I ran open with my DS-94 HST in my hawk, now I have closed ducts with the Dynamax.

At full power it felt pretty much the same, the big differance with mine was at 1/2 stick or power off the open duct felt like the brakes were on. With closed it glides much better at 1/2 stick and no power......but yours may be different
Sign up now
to remove ads between posts
Feb 20, 2013, 08:10 PM
Registered User
Hey, Nut. I sent you a PM.

Dennis
Feb 20, 2013, 10:33 PM
fly like an EAGLE ;)
corsair nut's Avatar
yeah, there relaly isnt much options for ducting, im pretty much forced to go open duct, i dont think it would fair too well at only 65% fsa on the inlet, especially with 4' long tail pipes lol. but after some test flights, i could always try it to see, you never know, the inlets have a decent radious, it might work ok. i have about 70% fsa on my jhh sabre back in the day and it was a ball of fire in the air, just took a little to get going. something to consider for the future, as i hate the idea that i could suck something in like a servo wire, retract tube, dirt, rocks ect. perhaps ill while up some adapters, its something that could be installed at the field, and tested right there.

looks like im planning to fly it from rosamond dry lake bed (aka edewards), talked to my good friend tony, who is now the club president, he said theres a smoother patch to the north of the painted runway, so i guess we'll give that a try, shouldnt be too bad with 4.5" tires, i just dont want the retracts getting the crap beat out of them....
Feb 21, 2013, 04:15 AM
Registered User
Si Goodchild's Avatar
Sorry, Gents, but I'm going to have to ask this again. How did you achive the elegant curves in the side of the fuslage without stress-cracking the foam? Did you simply bend it by hand, roll it over a surface or did you apply a little heat?

Si G
Feb 21, 2013, 07:29 AM
RC Fanatic
Reco's Avatar
Quote:
Originally Posted by Si Goodchild
Sorry, Gents, but I'm going to have to ask this again. How did you achive the elegant curves in the side of the fuslage without stress-cracking the foam? Did you simply bend it by hand, roll it over a surface or did you apply a little heat?

Si G
I believe it was achieved by just old fashoined sanding, shaping and hotwire . If you go back to the start of the thread you can see where Falcon just started with "Huge" lol blocks of foam. I dont think any bending was done. I may be wrong though.
Last edited by Reco; Feb 21, 2013 at 07:36 AM.
Feb 21, 2013, 08:44 AM
fly like an EAGLE ;)
corsair nut's Avatar
no huge blocks of foam really, just 1" thick slabs.

i pretty much just bent mine, remember, this thing is so long, those curves wernt too hard for the foam to do lol.
Feb 21, 2013, 09:32 AM
Registered User
Si Goodchild's Avatar
Quote:
Originally Posted by corsair nut
no huge blocks of foam really, just 1" thick slabs.

i pretty much just bent mine, remember, this thing is so long, those curves wernt too hard for the foam to do lol.
Brilliant, thanks very much for getting back to me.

Si G
Feb 21, 2013, 10:36 AM
Capt. Z
falcon5's Avatar
Yeah with contact glue aplyed to both pieces I started at one end and as soon as the pieces touch they are bonded, then when I got to the waist section were the big bend is just bend the foam to match the curve and touch them together.
Feb 21, 2013, 11:42 AM
RC Fanatic
Reco's Avatar
Quote:
Originally Posted by Si Goodchild
Brilliant, thanks very much for getting back to me.

Si G
I stand corrected lol I thought I remembered a huge block of foam must have been another build oh well I tried.
Feb 21, 2013, 01:12 PM
Capt. Z
falcon5's Avatar
Dug up the video of the last flight of good o'l 904...she was a good bird.

Andy T38 (4 min 39 sec)
Last edited by falcon5; Feb 21, 2013 at 01:23 PM.
Feb 21, 2013, 01:27 PM
EB-66C Team Member
J Morgan's Avatar
Man, that thing was so sweet Andy.

J
Feb 21, 2013, 02:29 PM
Oh wow, good Nyborg.
bd5wingnut's Avatar
Falcon

Great vid, looked very scale, sad to see the ending. Nasty stall in the dreaded low-n-slow.

Love the Moody Blues, etc. background music. Lee Greenwood free zone? LOL

Again sorry about the loss, it sux to put so much effort into a project and to lose it so quickly. But you do have the vid to visit. Thanx for sharing.

Wolf
Feb 21, 2013, 02:52 PM
Living a Dream
Hans-Joachim's Avatar
Andy, good o'l 904 was your coolest plane so far in my eyes.
HJ
Feb 21, 2013, 03:03 PM
Capt. Z
falcon5's Avatar
[QUOTE=Hans-Joachim;24207272]Andy, good o'l 904 was your coolest plane so far in my eyes.
HJ[/QUOTE

Yeah she was a perdy' plane. Nut will continue the T-38 legacy though..: )

Man I have to get my building jueces flowing again..I have a project in my head I need to turn into reality for the next Vegas.
Feb 21, 2013, 04:14 PM
fly like an EAGLE ;)
corsair nut's Avatar
get'r done wingman! for some reason, ive been on a building frenzy!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Cool Micro F-5/T-38 Parkflyer Build boingk Pusher Prop Jet Models 2 Oct 17, 2011 09:58 PM
Discussion I knew it wouldn't be long!!!!!!! Flightbox FPV Talk 8 Sep 29, 2011 05:17 PM
New Product 1/6 HETZER JAGDPANZER 38(t) Sd.Kfz. 138/2 r/c full metal BIG TANKS PLANT RC Tanks 0 Sep 28, 2011 02:38 PM
Sold Hangar Sale E-Flite P-38 rtf, GP Fokker, WM Miss America EP, Easyglider EZ T-38 ScaleBrad Aircraft - Electric - Airplanes (FS/W) 15 Jan 02, 2008 01:22 PM