New X8 WING - Page 51 - RC Groups
Thread Tools
Feb 09, 2012, 04:02 AM
Psionic001's Avatar
Photos people....
Please post lots of photos....
Camera Bays, bellies, places to install retracts!!!!
Sign up now
to remove ads between posts
Feb 09, 2012, 04:11 AM
Registered User
Daemon's Avatar
I've got a lot of big 3S batteries so am less interested in the stock low Kv motor meant to be run
at 4S voltage. Scorpion motors have been good to me (reliable, efficient, cool running, good power to
weight ratio, under rated max amps) so I picked up the last one of these
http://www.rcdude.com/servlet/the-12...ushless/Detail
SII-3020-1110Kv and plan to run it with a 12x8.5 folding prop.
Prop specs chart http://www.rcdude.com/servlet/the-te...1110Chart/Page
doesn't list that exact combo, but APC 12x8E maxes out at 82oz of thrust with highest
efficiency of any 3S prop combo in the chart. Hard to say how that'll play out at
lower cruising revs, but I don't have a lot of choices in folding prop sizes.

ian
Last edited by Daemon; Feb 09, 2012 at 04:16 AM.
Feb 09, 2012, 04:14 AM
Registered User
Daemon's Avatar
Quote:
Originally Posted by Psionic001
Photos people....
Please post lots of photos....
Camera Bays, bellies, places to install retracts!!!!
I haven't been posting fuse detail photos because they were all covered a few pages ago.
Start here and step through em https://www.rcgroups.com/forums/atta...mentid=4579837

And as I said above, the lower pocket is designed for a GoPro, so it's 60mm wide inside, and angled down 35mm.
Upper pocket is designed for flight camera, and it's 40mm wide inside.

If there's something not covered by those photos then tell us what specifically you need.

ian
Feb 09, 2012, 06:17 AM
Look Sideways at Polarisation
Funky Diver's Avatar




Wing mounting detail. You can see the additional spar inside the wing in the second photo. That runs the length of the entire wing.

You can also see that there are in fact two ply plates for location, there's also a hole through the wing. I'm going to be fitting a locking dowel into that to lock wings.
Feb 09, 2012, 06:31 AM
Registered User
Angelos's Avatar
Quote:
Originally Posted by Funky Diver
You can also see that there are in fact two ply plates for location, there's also a hole through the wing. I'm going to be fitting a locking dowel into that to lock wings.
Do you plan to use the glue that comes in the kit? I am considering using UHU Por instead as I have previously used it to glue ply to EPP and held really well.

Anyone else has views on this? Does UHU Por hold as good on EPO as it does on EPP?

Cheers,
Angelos
Feb 09, 2012, 06:57 AM
Look Sideways at Polarisation
Funky Diver's Avatar
I'm using UHU Por Angelos. It does a fabby job on EPO, it's what's holding my SkyWalker together.
Feb 09, 2012, 06:58 AM
Registered User
HI all

Are the wing tips mounted vertical or off to a out side angle

Thanks Jamie
Feb 09, 2012, 07:13 AM
um.. yeah, I can make that fly
Carlos230023's Avatar
uhu por is the only glue i use for foam these days, it grips well, is solid but allows for a bit of flex under stress, has a little expansion and grips like the best of them, two of my wings are held together with nothing but uhu por. highly recommended.

CJ
Feb 09, 2012, 07:23 AM
Foam Snow
Quote:
Originally Posted by Funky Diver
Wing mounting detail. You can see the additional spar inside the wing in the second photo. That runs the length of the entire wing.

You can also see that there are in fact two ply plates for location, there's also a hole through the wing. I'm going to be fitting a locking dowel into that to lock wings.
Can I be a pain and ask for a more zoomed out version of the pictures?

Are those wings ok to be detached and re-attached at flight time?
Feb 09, 2012, 07:32 AM
Registered User
Angelos's Avatar
Quote:
Originally Posted by heinduplessis
Are those wings ok to be detached and re-attached at flight time?
Yes, they can be detached. Remove a pin (or plastic nylon screw that I will probably use) and slide the wing out. The pin locks two piece of ply together one of which is glued on the wing and the other on the fuselage.

The servo will obviously need to disconnect together with any other FPV gear that may be sitting on the wing (VTX, UHF receiver etc).

-Angelos
Feb 09, 2012, 07:35 AM
Psionic001's Avatar
Thanks for those photos.

Is the spar quality any good? Or would you consider some solid spars in there?
What's the spar diameter?


Quote:
Originally Posted by Funky Diver

Wing mounting detail. You can see the additional spar inside the wing in the second photo. That runs the length of the entire wing.

You can also see that there are in fact two ply plates for location, there's also a hole through the wing. I'm going to be fitting a locking dowel into that to lock wings.
Feb 09, 2012, 08:16 AM
Registered User
Just got my X8 today, only missing the motor. I think i'll wait with the build until i see some buildblogs :P i think maybe i'll use quick epoxy instead of uhu por. oh, and 1 thing.. i cant figure out where the 2 small square balsa is going..
Feb 09, 2012, 08:33 AM
My other vehicle is unmanned
fpvnick's Avatar
I will probably use ca on her as i have with all my funjets and previous wings. Its light and quick setting when used with kicker making lining up parts easy. I never had any problems with it in the past. I have a tube of uhu por as well ill keep it handy incase i need some.
i didn’t notice that the carbon spar ran the hole length of the wing great.
Feb 09, 2012, 08:38 AM
Look Sideways at Polarisation
Funky Diver's Avatar
Quote:
Originally Posted by Bauf
i cant figure out where the 2 small square balsa is going..
Which balsa? I never received any in mine.
Feb 09, 2012, 08:43 AM
Registered User
Quote:
Originally Posted by Funky Diver
Which balsa? I never received any in mine.
im sorry, plywood :P


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product X8---new 2.4GHz Radio System ASSAN Radios 5745 Mar 15, 2017 11:31 AM
For Sale Assan 2.4 ghz X8 6ch receiver Brand New Scooter33 Aircraft - General - Radio Equipment (FS/W) 2 Oct 12, 2011 10:34 AM
Discussion Any info regarding this x8 setup?Better than coax x8? sjak Multirotor Drone Talk 11 Aug 14, 2011 09:33 AM
Sold New Assan Module X8 2.4 for JR Tx norstaroption Aircraft - General - Radio Equipment (FS/W) 6 Nov 21, 2009 06:42 AM
Sold New - 4 (Four) ASSAN X8 R6 6Ch 2.4GHz Receivers - $105 EyeFlyPlanes Aircraft - General - Radio Equipment (FS/W) 0 Oct 20, 2008 03:39 AM