Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Nov 11, 2012, 01:55 PM
Imagecatcher is offline
Find More Posts by Imagecatcher
Registered User
Imagecatcher's Avatar
Quote:
Originally Posted by rsands2801 View Post
its underpowered. no question about it...if it was right tension it would have sailed way further. 13-14kg is alot of pull, its way more than what you think it feels like
But when i attach a set of luggage scales to the cradle it is pulling 40kgs! Plus the motor @ near full whats to fly out of the wing rests before release.
Its 5.50am, not a breathe o wind, im getting up! Report Success or Fail soon.
Sign up now
to remove ads between posts
Old Nov 11, 2012, 02:02 PM
Daemon is offline
Find More Posts by Daemon
Registered User
Daemon's Avatar
How much tension when stretched to the midpoint of the launcher? I'm guessing you're
only getting 40kg in the last few cm of stretch and it's dropping almost instantly
as soon as the plane moves.

ian
Old Nov 11, 2012, 02:04 PM
brifa is offline
Find More Posts by brifa
Registered User
brifa's Avatar
Quote:
Originally Posted by brifa View Post
how many cm behind or forward the holes under the wings should i put the CG??
and which is the best place to put the video tx?? i have the uhf antenna on the right in the middle of the plane at 5 cm from the wing joiner..

thanks
Old Nov 11, 2012, 02:09 PM
Daemon is offline
Find More Posts by Daemon
Registered User
Daemon's Avatar
Quote:
Originally Posted by brifa View Post
how many cm behind or forward the holes under the wings should i put the CG??
As has been many times in this thread, the CG should be at the rear edge
of the front finger holes.

ian
Old Nov 11, 2012, 02:24 PM
Imagecatcher is offline
Find More Posts by Imagecatcher
Registered User
Imagecatcher's Avatar
Quote:
Originally Posted by Daemon View Post
How much tension when stretched to the midpoint of the launcher? I'm guessing you're
only getting 40kg in the last few cm of stretch and it's dropping almost instantly
as soon as the plane moves.

ian
I'll check that out Ian
Old Nov 11, 2012, 02:42 PM
Skipper Billy is offline
Find More Posts by Skipper Billy
Registered User
ImageCatcher - its not just about tension but duration of pull and how fast the level of pull declines.

My launcher pulls the same as Coyotes - about 12kg - but it pulls for over 4 seconds. From launch it will climb to about 30 metres - high enough to do a full lap of the field and land back at my feet without ever touching the throttle ie just the bungee.

My guess is that your launcher (as Coyote said) is an animal at launch but within a few inches has 'shot its bolt'.

X8 Maiden Flight - Alba Aviation (1 min 40 sec)
Old Nov 11, 2012, 03:00 PM
Dr.Tom is offline
Find More Posts by Dr.Tom
Youtube: TomRi25
Dr.Tom's Avatar
X8 plane FPV flight 3km out and back (3 min 24 sec)


for now... link is solid and gonna push it a bit more...


Old Nov 11, 2012, 03:31 PM
Coyote64 is offline
Find More Posts by Coyote64
Praying for better weather
Coyote64's Avatar
Not bad mate, they really are good for covering range with 2x large lipo`s on board, I wanted to fly mine with 4x but it just seems way to heavy for it, and the extra weight I think will kill the cruise current draw but I`m yet to try it.

I suppose I should post a video up as I don`t think I have apart from the spin video

X8 10km FPV flight (7 min 10 sec)


Stupid JapanDVR that is supposed to be great froze and didn`t record the FPV cameras transmission. Luckily I was broadcasting live over Justintv.com to the UK forum lads so managed to download the live uploaded video from there to add to the Gopro footage.

10km done, but after landing as I thought previously Hornet OSD current sensor is miles out, over 30% in this case so could have gone a lot further.

Now I have swapped Hornet / FY31AP out for RVOSD Gen 5. Also now swapped out the motor for a Turnigy SK 840KV motor on a 12x8 prop so should now be able to push it knowing the current usage will be accurate and have a faster but more efficient cruise.
Last edited by Coyote64; Nov 11, 2012 at 03:43 PM.
Old Nov 11, 2012, 03:55 PM
Dr.Tom is offline
Find More Posts by Dr.Tom
Youtube: TomRi25
Dr.Tom's Avatar
thnx,
but yours is great!
what gear do you use?

I have
2x 5000 4S onboard, turnigy 830KV motor, aeronaut folding 13x6.5 prop
rangelink 433 LRS
racewood vid RX
readymadeRC 1500mw 1.3GHz TX
Ibcrazy skew planar on model and crosshair 10db at my side. (both from readymaderc)
on second flight I've put on 500mw racewood tx to compare, vid was clear as 1500mw, same distance, so I guess there is some more range left to try
Old Nov 11, 2012, 04:06 PM
Coyote64 is offline
Find More Posts by Coyote64
Praying for better weather
Coyote64's Avatar
For that flight I had

WDR650 Camera
Gopro
ImmersionRC 2.4ghz 500mw
Home made cloverleaf ( to clear carbon of prop )
Chainlink UHF
2x 5000 4S Nano-Techs
Hornet OSD + FY31AP
Telefly OSD ( for antenna tracking )
12v PSU
Circular-Wireless 12dbi helical
Scorpion 2030 1110kv V2 with a 10x6
Old Nov 11, 2012, 04:10 PM
Daemon is offline
Find More Posts by Daemon
Registered User
Daemon's Avatar
1500mW is overkill.
I can reach out 4.5km easily using CP omnis (CL + SWP) on only 600mW (FOX800)..
Been well past 10km with a Crosshair on the Rx and could go much further.

ian
Old Nov 11, 2012, 05:25 PM
brifa is offline
Find More Posts by brifa
Registered User
brifa's Avatar
so at 440 mm from the nose??
why somebody says it's better at 445 mm from the nose??


Quote:
Originally Posted by Daemon View Post
As has been many times in this thread, the CG should be at the rear edge
of the front finger holes.

ian
Old Nov 11, 2012, 05:51 PM
xviper is offline
Find More Posts by xviper
Registered User
Quote:
Originally Posted by brifa View Post
so at 440 mm from the nose??
why somebody says it's better at 445 mm from the nose??
5mm doesn't make one bit of difference.
Old Nov 12, 2012, 01:51 AM
7536jake is offline
Find More Posts by 7536jake
Registered User
Hey guys, been looking through these posts, very interesting. I just ordered my X8, whats a good endurance package for it that will have good power and long flight?
Old Nov 12, 2012, 02:05 AM
7536jake is offline
Find More Posts by 7536jake
Registered User
Hey Coyoto or anyone else, i see everyone says 2x4s battery ect ect. By this do you mean you have soldered them together to both power your motor? or is just 1 powering the motor and one doing cameras ect?
Last edited by 7536jake; Nov 12, 2012 at 02:39 AM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product X8---new 2.4GHz Radio System ASSAN Radios 5744 Oct 11, 2016 01:30 AM
For Sale Assan 2.4 ghz X8 6ch receiver Brand New Scooter33 Aircraft - General - Radio Equipment (FS/W) 2 Oct 12, 2011 10:34 AM
Discussion Any info regarding this x8 setup?Better than coax x8? sjak Multirotor Talk 11 Aug 14, 2011 09:33 AM
Sold New Assan Module X8 2.4 for JR Tx norstaroption Aircraft - General - Radio Equipment (FS/W) 6 Nov 21, 2009 06:42 AM
Sold New - 4 (Four) ASSAN X8 R6 6Ch 2.4GHz Receivers - $105 EyeFlyPlanes Aircraft - General - Radio Equipment (FS/W) 0 Oct 20, 2008 03:39 AM