Shop our Airplanes Products Drone Products Sales
Thread Tools
Nov 15, 2012, 08:25 PM
Registered User
smithder's Avatar
I managed to break my firewall. 3DHS is out of stock but I read a guy using the yak firewall and with some trimming got it to work. Any know if that works or better yet have a firewall they would sale me?
Sign up now
to remove ads between posts
Nov 16, 2012, 06:40 PM
Registered User
Not even close to a 3D master but loving this plane, I have been keeping her three mistakes high right now. Did some flat spins, snap rolls, knife edge, knife edge loops, and some hovering. Land her on low rates and fly her on high, pretty nice plane!

So far so good!
Nov 19, 2012, 07:55 AM
KING of PING!
JDMCARPETS's Avatar
like to buy one of these http://www.dailymail.co.uk/news/arti...illed-car.html
Nov 19, 2012, 11:44 AM
Registered User
After seeing you guys beating up your Extra. I decided to fly her harder. So yesterday afternoon I took the advantage of the school yard being empty, cold and windy btw; I flew her as low as possible, dragging her rudder a few times and the first time I did harrier rolling circles within 5' above the deck. Got a bit too aggressive and the wind tip scratched the ground and broke the SFG in half. This is my first damage on this bird other than the LG mount. Anyway, I kept flying the bird with only half of the right SFG attached until the sun went down. What a nice way to end a day and cheered me up after another pathetic game of Eagles.

One problem though, my 130g is getting louder and louder, it still swings freely by hand and I do not feel any robbing between the can and the stator but the noise is noticeable in the air. If a new bearing set would help?
Nov 19, 2012, 04:05 PM
3D? I only got two thumbs!
Quote:
Originally Posted by Vince_TT
One problem though, my 130g is getting louder and louder, it still swings freely by hand and I do not feel any robbing between the can and the stator but the noise is noticeable in the air. If a new bearing set would help?
I had this problem with the omega 130 in my 48" epp yak. I abused the motor a little early on (ran it with a loose motor mount for a few flights before I noticed). I replaced the bearings with boca bearings - theres a post somewhere around here with a video showing how to do it. The noise changed, but did not improve significantly. So either I botched the bearing replacement, or the source of the noise is elsewhere. I put a new omega in as a quick fix, I've got the old one on the bench waiting for inspiration on how to fix it.

So I don't know if a bearing set would help you, but I'm interested in wether it does, or what else might get suggested here.
Nov 19, 2012, 07:03 PM
Registered User
hello, i just got my extra put together. I got it here and used so it needed repair. It hsa a torque 2818 w14x7, hs65, and an 60amp esc since it was sent by mistake. Ive set it up per the manual and if it wasnt so cold out and getting dark already id go test fly it. Any tips or suggestions would be great.

Also,does anyone know hows much right and down thrust is this should have? i glued the firewall back in but its been repaired before and it looks a little extreme
Nov 19, 2012, 07:52 PM
Registered User
Quote:
Originally Posted by olds455
hello, i just got my extra put together. I got it here and used so it needed repair. It hsa a torque 2818 w14x7, hs65, and an 60amp esc since it was sent by mistake. Ive set it up per the manual and if it wasnt so cold out and getting dark already id go test fly it. Any tips or suggestions would be great.

Also,does anyone know hows much right and down thrust is this should have? i glued the firewall back in but its been repaired before and it looks a little extreme
My firewall is still original. The thrust angles are very little (almost none) in my view.
Nov 19, 2012, 08:07 PM
Registered User
thanks ill have to do some shimming
Nov 19, 2012, 08:18 PM
KING of PING!
JDMCARPETS's Avatar
It has a torque 2818 w14x7, is going to burn up/ t- 2814-820 w 14x7 will be fine
Nov 19, 2012, 08:24 PM
Registered User
Quote:
Originally Posted by olds455
thanks ill have to do some shimming
Forgot to mention that, if you fly off grass field, avoid harrier landing will keep your LG mount and tail wheel intact. Since I changed my approach by harrier down to about a foot and then switching to normal landing, no more broken pieces in that department.
Nov 19, 2012, 08:28 PM
Registered User
thanks vince, Im not to good at the harriers yet so ill keep that in mind.
Nov 19, 2012, 08:33 PM
Registered User
Quote:
Originally Posted by olds455
thanks vince, Im not to good at the harriers yet so ill keep that in mind.
Believe me, this bird will make every pilot look like a harrier master.
Nov 19, 2012, 08:40 PM
Registered User
Cool, I also just finished my 47 shp to go with the 41 edge i picked up last month. Im finding the 6 of the polyrc/enerland packs i have will barely hold 30amps and 300w and fall off quickly. i repowered my 1900 based on these batteries and theyre not working worth a damn. the turnigys i have are much better.
Nov 20, 2012, 05:57 PM
Registered User
I got my first flight in tonight. Just 5 min worth and it flies really well. two clicks trim and it was ready for what little fun i can give it. I might need a little more control throw especially on the elevator. It took full to try and get it into hover and i On could hold it a few sec. the 2818 was on 14x7 and gave 385w and 38a before take off. I may need the omega 130 for this and use the 2818 on my shp. I do have some better batteries coming and i need some warmer temps, its 13deg out there
Nov 20, 2012, 06:49 PM
Registered User
Congratulation! Even though she is a blast to fly, but I won't do that in 13 degree!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Precision Aerobatics 48'' Extra 260 Build Thread! edge5foamy 3D Flying 5861 Today 02:39 PM
Sold 3DHobbyshop 38" EPP Slick NIB cjdscratch Aircraft - Electric - Airplanes (FS/W) 4 Oct 23, 2011 11:21 AM
Sold 3DHobbyshop 38" EPP Slick NIB cjdscratch Aircraft - Electric - Airplanes (FS/W) 2 Oct 22, 2011 09:58 PM
Found 3DHobbyshop 55" Extra 300SHP gabrielisrael Aircraft - Electric - Airplanes (FS/W) 1 Sep 15, 2011 06:56 PM
48" Bat EPP and 48" Bee EPP closeouts stegre Aircraft - Sailplanes (FS/W) 1 May 20, 2005 10:20 AM