Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jan 06, 2012, 10:01 AM
Stone1295 is online now
Find More Posts by Stone1295
AMA 937634
Stone1295's Avatar
All I've seen on the diydrones site /forum is that the next release will occur in February but this may only be speculation as it wasn't an official announcement.

They mentioned that they've got them in stock and that they were testing them and that the 6-8 week lead time was going to be mostly due to the initial demand for them. Still, since my order I've received 2 emails from them but neither of the emails had any shipping information.

At least that's how I understand the situation.

-Mike
Sign up now
to remove ads between posts
Old Jan 06, 2012, 02:39 PM
RC Man is offline
Find More Posts by RC Man
A man with too many toys
With the lower price, smaller size, and improved performance this is probably going to be the one to get on 2013. It also flies anything so I can see why the demand is very high. As ling as I get it for spring flying I will be happy.

.
Old Jan 07, 2012, 12:40 AM
Stone1295 is online now
Find More Posts by Stone1295
AMA 937634
Stone1295's Avatar
Those were my thoughts as well. It's winter here so all I'm hoping is that I get it in time to test it out and play with it before spring comes!

-Mike
Old Jan 07, 2012, 06:51 PM
RCvertt is offline
Find More Posts by RCvertt
Registered User
RCvertt's Avatar
Quote:
Originally Posted by RC Man View Post
...this is probably going to be the one to get...
Agree. The size looks really good compared to the previous version.

I'd like to see the next version get even smaller. I think it's possible if they do like the Nano and put components on both sides of the board. Looks like the atmel chip could go on the bottom and the GPS put in its place and such.

Wondering how well that grouped 12 pin sensor shield socket is going to keep vibrations away form the sensors. Nothing a little hot glue on the corners can't fix if its a problem though.
Old Jan 13, 2012, 04:05 PM
Tom Harper is offline
Find More Posts by Tom Harper
Lift is cheap - Drag sucks
Tom Harper's Avatar
Clarification - It is described as 'A' board but the photos show two boards. So is this a complete system for $199 or a mother board that supports other components?

Sorry, but I am not familiar with these products.

Tom
Old Jan 13, 2012, 06:36 PM
brakar is offline
Find More Posts by brakar
Registered User
brakar's Avatar
Tom, I think it's safe to say both hardware and firmware are still under heavy development at diydrones. After testing all their hardware and a bunch of supposed to be stable firmware versions, I have decided to go into a wait and see mode. (I am however impressed by their progress).
Old Jan 13, 2012, 06:53 PM
Tom Harper is offline
Find More Posts by Tom Harper
Lift is cheap - Drag sucks
Tom Harper's Avatar
Thanks - this one is tempting.

Tom
Old Jan 13, 2012, 07:53 PM
brakar is offline
Find More Posts by brakar
Registered User
brakar's Avatar
Agree, (I have one in order). But, any "production ready" firmware in existence?
Old Jan 14, 2012, 10:45 AM
Peter Seddon is offline
Find More Posts by Peter Seddon
Registered User
I think you may find the latest Arducopter firmware supports the new board - whether it is fully tested I know not.

Peter
Quote:
Originally Posted by brakar View Post
Agree, (I have one in order). But, any "production ready" firmware in existence?
Old Jan 15, 2012, 05:58 AM
RCvertt is offline
Find More Posts by RCvertt
Registered User
RCvertt's Avatar
Quote:
Originally Posted by Tom Harper View Post
Clarification - It is described as 'A' board but the photos show two boards. So is this a complete system for $199 or a mother board that supports other components?
For $199 you get a complete system. You get a mother board and most sensors.
Old Jan 15, 2012, 05:59 AM
RCvertt is offline
Find More Posts by RCvertt
Registered User
RCvertt's Avatar
Not sure if it's just the mother board part that they will ship to you latter due to the current demand, but for $200 you get both boards eventually which is the assembled kit.
Old Jan 15, 2012, 04:21 PM
arroxfive is offline
Find More Posts by arroxfive
Registered User
Hi guys, any news of the board dimensions and mounting holes?

Thx
Steven

Sent from my BlackBerry 8900 using Tapatalk
Old Jan 15, 2012, 04:33 PM
Stone1295 is online now
Find More Posts by Stone1295
AMA 937634
Stone1295's Avatar
From the DIYDrones site:

"The board itself is our first four-layer design and is smaller than APM 1.0 (believe it or not itís just 2.6 x 1.6 inches, even smaller than the UDB) and this includes four mounting holes and rounded edges to give a nicer look and feel! Of course itís lead free and ROHS complaint."

They don't mention the measurements of the mounting holes but here's the link:

http://www.diydrones.com/profiles/blogs/apm-2-0-release

-Mike
Old Jan 16, 2012, 04:06 PM
Tom Harper is offline
Find More Posts by Tom Harper
Lift is cheap - Drag sucks
Tom Harper's Avatar
RCvertt,

Thanks - impressive price!

Tom
Old Jan 25, 2012, 10:14 PM
RCvertt is offline
Find More Posts by RCvertt
Registered User
RCvertt's Avatar
What GPS is going to be on this board? Looks like weaker MediaTek MT3329 GPS 10Hz.

Will there be a way to use a more powerfull GPS like the GS407 U-Blox5 GPS 4Hz (New Antenna & Free uBlox Adapter Basic)?

----------
Never mind looks like the answer is already here.

"...the daughter board will come in four flavors: GPS+MAG+SD, GPS+SD, MAG+SD and SD. For example if you want to attach only the magnetometer (Compass) externally you just buy the option GPS+SD."

Maybe they could offer one more daughter board option... Powerful GPS+ MAG+SD
Last edited by RCvertt; Jan 25, 2012 at 11:54 PM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Selling my Ardupilot Mega ababb88 UAV - Unmanned Aerial Vehicles 9 Oct 05, 2011 06:55 PM
Sold ArduPilot Mega RTF hobbyboy FPV Equipment (FS/W) 0 Sep 26, 2011 03:52 PM
Question Ardupilot Mega: how much time do I have to stabilize the gyros? marhar UAV - Unmanned Aerial Vehicles 1 Sep 23, 2011 10:29 AM
Discussion ArduPilot Mega kit from DIY Drones any good? spacecase Multirotor Talk 11 Aug 11, 2011 02:07 PM
Wanted Full ArduPilot Mega kit actionplus Aircraft - Electric - Multirotor (FS/W) 2 Aug 11, 2011 02:23 AM