Thread Tools
Old Mar 09, 2012, 01:50 AM
Brosol is offline
Find More Posts by Brosol
Brosol
Brosol's Avatar
@jlk69: Are you using a stock flybar?
Sign up now
to remove ads between posts
Old Mar 09, 2012, 03:02 AM
Aaron qin is offline
Find More Posts by Aaron qin
Aaron qin's Avatar
Quote:
Originally Posted by mystman View Post
That doesn't help. I also tried oiling the motor, without success.



I've just contacted bangood but hope to get some help from here.
Here is the video.

http://youtu.be/s8_CqSuiwdk
I think it's not the faulty motor,or it would not spin at all.Try to put it into a warm place,the oil may frozen to run slow.
When you increase the throttle a little bit,the tailmotor would run normally,I had this experience with my xieda 9958.Anyone experienced this before?
Site Sponsor
Last edited by Aaron qin; Mar 09, 2012 at 03:15 AM.
Old Mar 09, 2012, 03:15 AM
jl1252 is offline
Find More Posts by jl1252
Registered User
jl1252's Avatar
Aaron, I sent you a PM.

jl1252
Old Mar 09, 2012, 06:52 AM
andur is offline
Find More Posts by andur
Registered User
I just came to the idea that maybe the V911 transmitter can be bound to a different receiver? Possibly thus making it compatible with an airplane receiver or something similar? That could be nice! How could we check?
Old Mar 09, 2012, 07:49 AM
mystman is offline
Find More Posts by mystman
Registered User
Quote:
Originally Posted by Aaron qin View Post
I think it's not the faulty motor,or it would not spin at all.Try to put it into a warm place,the oil may frozen to run slow.
When you increase the throttle a little bit,the tailmotor would run normally,I had this experience with my xieda 9958.Anyone experienced this before?
That doesn't work. I always have to shortly turn the tail blade to start. If it stops again most of the time I have to reapt this procedure.
Hope to get an answer from bangood soon (still waiting).
Any other possibilities to solve this?
Old Mar 09, 2012, 09:32 AM
jameschen072 is offline
Find More Posts by jameschen072
The flightless bird
jameschen072's Avatar
Quote:
Originally Posted by andur View Post
I just came to the idea that maybe the V911 transmitter can be bound to a different receiver? Possibly thus making it compatible with an airplane receiver or something similar? That could be nice! How could we check?
It is possible (maybe a turnigy compatible receiver) but I would advise highly against it... you may experience range issues since this transmitter is designed for indoor/short-range usage... The lack of even the most basic reverse switches may also be a problem...
RCG Plus Member
Latest blog entry: The Fei-Lun FT011 Review
Old Mar 09, 2012, 09:57 AM
JoshWildFlyer is offline
Find More Posts by JoshWildFlyer
The Budget Man

Faulty charger


The yellow circles highlight the poor soldering. Unfortunately, my soldering iron is spoilt...Have to buy one to fix this. Sigh I wish they had better QC in this particular department...
Old Mar 09, 2012, 10:25 AM
nr1 is offline
nr1
Find More Posts by nr1
nr1
Registered User
Hi guys,

i also got my V911 now.
In fact the helicopter is very nice, i only have one small problem: The heli seems to fly always some degrees sloped in the vertical axis. So it looks as if the heli is "hanging" around in the air a bit sloped.

Any hints?

Any tipps what could
Old Mar 09, 2012, 10:27 AM
cgpirre is offline
Find More Posts by cgpirre
Registered User
cgpirre's Avatar
Mine does that too, I think it's normal. If I look at it from the front when it's hoovering, it is 'leaning' to the left.
Old Mar 09, 2012, 10:27 AM
SG Mason Knives is offline
Find More Posts by SG Mason Knives
Registered User
OK so after reading 300+ pages in this thread I guess my decision to purchase the V911 wasn't a bad one and armed with all the tips on how to fix the things that could be wrong with it I should be good to go when it gets here. Unfortunately I didn't order from one of the main suppliers that are mentioned here and I paid too much for it.
Old Mar 09, 2012, 10:35 AM
Daryoon is online now
Find More Posts by Daryoon
Team WarpSquad
Daryoon's Avatar

@nr1


Quote:
Q 1: My heli is not hanging straight once in the air? I can't trim that out, is it broken?

A: This is completely normal. The sideways pressure of the tail rotor would make the heli slide left all the time, unless the rotor disc is tilted a little to the right to compensate this. So the heli will be, or need to be, trimmed a little to the right on the roll channel, and hence the heli does hang to the right in a stable hover. After a while you will become accustomed to this, and consider it normal. Most of these ultra small single rotor helis show this effect, and even bigger ones, but the heavier weight might reduce the tilt angle.
The above is quoted from the Nine Eagles Solo Pro I/II/V1/V2/270/Bravo SX FAQ
Old Mar 09, 2012, 11:01 AM
nr1 is offline
nr1
Find More Posts by nr1
nr1
Registered User
Quote:
Originally Posted by Daryoon View Post
Ok thx, so this is normal

One more question:
Is there anywhere a 'manual' for adjusting / setting up the swashplate? (I'd like to fine adjust it)
Old Mar 09, 2012, 11:17 AM
Heli Pad is offline
Find More Posts by Heli Pad
Against Helicopter Cruelty
Heli Pad's Avatar
Quote:
Originally Posted by nr1 View Post
Ok thx, so this is normal

One more question:
Is there anywhere a 'manual' for adjusting / setting up the swashplate? (I'd like to fine adjust it)
Daryoon is your "go-to" guy for that question. Just click on his name and read his blog. Look for "Mechanical Trimming" (towards the bottom of the page).
Old Mar 09, 2012, 12:51 PM
nr1 is offline
nr1
Find More Posts by nr1
nr1
Registered User
Quote:
Originally Posted by Heli Pad View Post
Daryoon is your "go-to" guy for that question. Just click on his name and read his blog. Look for "Mechanical Trimming" (towards the bottom of the page).

thx a lot!
Old Mar 09, 2012, 12:54 PM
cgpirre is offline
Find More Posts by cgpirre
Registered User
cgpirre's Avatar
Slowly I'm starting to get the hang of it, and I'm having a load of fun with this nimble thing. I'm at flight number #5 of both batteries, time to up the flight time


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Jiuchon 9C002, a Solo Pro clone? SoloProFan Micro Helis 103 Feb 29, 2012 03:24 PM
Discussion Interesting Solo Pro? Clone gordonzo Micro Helis 46 Nov 30, 2011 04:15 AM
Question Which 100 sized heli after Solo Pro? Tuc Micro Helis 16 Jun 13, 2011 02:52 PM
Sold $100 !NEW ARF Storm 250 (Trex Clone) With Align Upgrades, Tons of Extras! $100!! RChelisrule Aircraft - Electric - Helis (FS/W) 1 May 31, 2011 01:26 AM