New Products Flash Sale
Thread Tools
Old Nov 15, 2011, 04:16 PM
alvarezpja is offline
Find More Posts by alvarezpja
Jose Angel

Newbie problems with Hoverfly Pro

Hi All,

I'm configuring my brand new hoverfly PRO but have some problems.

My 3S lipo is connected to POWER connector, one of the ESC with power/ground lines connected to ESC port and the receiver connected taking power from the board.

I have checked in "HoverFly Setup" software, that all radio channels are readed appropriately and AH also responds ok when moving the hexa in all directions.
Autoleveling and AltitudeHold switches also responds ok and are disabled by default.

When powering the board, I can arm normally but when I give throttle all motors accelerate proportionally to throttle level, but motors does not respond to yaw/roll/pitch orders nor quad movements...

Any ideas?

Thanks in advance.
Sign up now
to remove ads between posts
Old Nov 15, 2011, 06:38 PM
Stacky is offline
Find More Posts by Stacky
Pants first, then shoes
I had a similar problem which ended up being that I had connected the motors incorrectly to the HFP configuration. Double check that you have the Hexa firmware loaded and then check that you have the correct motors connected to the correct pins on the HFP. I was sure I had all this correct but when I checked it again for the 4th time I found I had made a mistake.
Old Nov 15, 2011, 06:44 PM
mspencer is offline
Find More Posts by mspencer
Flight Instructor
So your ship will not respond to any stick movement except for the throttle? If so did you do an accelerometer calibration? Do you have your gain high enough?
Old Nov 15, 2011, 11:00 PM
Adidas4275 is offline
Find More Posts by Adidas4275
manual flying apologist
Adidas4275's Avatar
Does the HFPro board take 12v input?

I have mine connected to a 5v uBEC, and it works fine.

Old Nov 16, 2011, 02:10 AM
alvarezpja is offline
Find More Posts by alvarezpja
Jose Angel
Adidas4275, I read in the manual that HFP should be power with I thought I should connect it to the 3S (althought I see the board boots ok when powered from the 5V USB)

mspencer, my gain is 25 as recommended by HF manual. Checked with HF Software.

Stacky, I will review my connections maybe I did a mistake. The HF layout for motor connection is not really intuitive

Thanks for the responses!
I'll report later!
Old Nov 16, 2011, 03:43 AM
elossam is offline
Find More Posts by elossam
Registered User
You will not see any stick reaction untill the thr is over 1/3 or more. Ask a friend to hold the ufo from de lower part of the frame, apply thr and check for stick imputs ans self corrections.
Old Nov 16, 2011, 07:27 AM
photronix is offline
Find More Posts by photronix
Al Ducharme
photronix's Avatar
Couple things. The USB is 5V but it bypasses the 5V regulator on the HFP. The Power needs to be ~6V-16V. The gain of 25 in the manual is a "Suggested" starting point. You may need more gain.

Are you using a HFGPS with the HFP that won't respond?

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion AXN Clouds Fly - problems problems problems :( spacemanspiff33 Beginner Training Area (Aircraft-Electric) 23 Oct 03, 2011 12:27 AM
FP Pic Newbie Problems Invertigo Micro Helis 3 Jul 11, 2003 11:30 PM
newbie corona problems ProfitOfDoom Electric Heli Talk 20 May 11, 2003 01:33 AM
Need help with some basic newbie problems.. Ozzy Parkflyers 7 Oct 27, 2002 03:53 PM
newbie zagi 400x motor problems: HELP QUICK!!!! zagman Foamies (Kits) 5 Jan 24, 2002 04:11 PM