Thread Tools
Jun 01, 2012, 03:06 PM
Team EJF >>>WHOOSH>>>
AceMigKiller's Avatar
No prob!
Sometimes important stuff like that gets lost in useless thread chatter
Lemme know if you need any more tips or clarification.

Vic
Sign up now
to remove ads between posts
Jun 01, 2012, 03:54 PM
Done it all
Well, all was good and I was on the way to finishing this bird over the weekend, but then

I hooked up the servo, linkage, and all worked. Test fitted it, perfect, but then I noticed the elevator tips were not even, were they warped? Nope, one of the cloth hinges was not right. It showed too much and it had play.

Resolution, I cut the elevator off, used my fingernails to remove the tape and now I will make new slots and use pinned hinges.

PS: the 1/4 strip that runs inside the trailing edge of the stab is harder wood than balsa, hard to cut new hinge slots.
Jun 01, 2012, 04:29 PM
3DHOG
jcdfrd's Avatar
it is becoming more apparent that the quality of wood in each kit/stab is all over the place.
after opening up Nicks stab and inspecting it, he had a pretty good one the spar and trailing blocks were all nice hard balsa pieces but in tams stab it is extremely soft balsa
Jun 01, 2012, 05:30 PM
Team EJF >>>WHOOSH>>>
AceMigKiller's Avatar
Quote:
Originally Posted by SCALEFAN
the 1/4 strip that runs inside the trailing edge of the stab is harder wood than balsa, hard to cut new hinge slots.
Use a Dremel. Makes quick work of cutting hinge slots.
Jun 01, 2012, 05:57 PM
Hey Ya'll!! Watch THIS!!
Michael Paxton's Avatar
Quote:
Originally Posted by acemigkiller
use a dremel. Makes quick work of cutting hinge slots.
+1
Jun 01, 2012, 06:21 PM
Done it all
Oh man, thanks. I never thought of that. So simple and easy.
Jun 02, 2012, 09:35 AM
Done it all
All is well, new pin hinges installed, tape re-applied, it came out perfect. I filled in the excess hinge slots with Hysol, pressed it in with my fingers, then wiped the surface clean, so there is no bumps or restrictions to the elevator operation.

Thanks again for the simple solution to the problem. I am now excited about this project.

Al
Jun 02, 2012, 09:50 AM
Lee Liddle
Knife Liddle's Avatar
Which color do you have Al? My three Sniper 90`s all flew great, just needed reinforcement to go fast.
Jun 02, 2012, 11:36 AM
Done it all
White, Red, and Blue. I am slightly color blind, so the colors could be White, Orange and Purple. LOL
Jun 02, 2012, 01:20 PM
Lee Liddle
Knife Liddle's Avatar
So that`s the clasic Sniper scheme. Of those offered right now, I`d go with that one too, Good visability and good colors. I like the red and white High Viz too, but it`s not quite what I expected.

Good luck with yours.
Jun 02, 2012, 04:02 PM
Hey Ya'll!! Watch THIS!!
Michael Paxton's Avatar
Quote:
Originally Posted by Knife Liddle
So that`s the clasic Sniper scheme. Of those offered right now, I`d go with that one too, Good visability and good colors. I like the red and white High Viz too, but it`s not quite what I expected.

Good luck with yours.
Yea I'm with you. Not quite what I was hoping for. But should be easy to see.
Jun 02, 2012, 05:33 PM
Done it all
I feel like I had to post these positive stuff about this plane.

I just cut out the servo covers and expected the wings to be the typical construction, cheap wood, covered by cheap shrink covering, boy was I surprised. The wings are composite and painted. I would love to know how they did it.

After inspecting the rest of the parts, not many, I find this plane to be one heck of a bargain. I really think that it is strong and could easily stand up to my abuse.The stab install was easy, so long as you know what has to be done. Just do it right the first time.

Thanks to the few guys that sacrificed their planes in the process of isolating some potential elevator issues, when flown at high speed. We are grand daughter sitting or I would finish it tonight and fly tomorrow. This is the first plane that I ever assembled and changed my mind from bad to good.

Maiden will have to be in two weeks, going to AZ next weekend.
Jun 02, 2012, 06:29 PM
wannabe Jet guy
CRCJA's Avatar

Az


Where in AZ? you bringing some planes to fly? I might have a Sniper to build by then.

Ralph

Quote:
Originally Posted by SCALEFAN

Maiden will have to be in two weeks, going to AZ next weekend.
Jun 02, 2012, 06:49 PM
Lee Liddle
Knife Liddle's Avatar
Quote:
Originally Posted by SCALEFAN
I feel like I had to post these positive stuff about this plane.

I just cut out the servo covers and expected the wings to be the typical construction, cheap wood, covered by cheap shrink covering, boy was I surprised. The wings are composite and painted. I would love to know how they did it.

After inspecting the rest of the parts, not many, I find this plane to be one heck of a bargain. I really think that it is strong and could easily stand up to my abuse.The stab install was easy, so long as you know what has to be done. Just do it right the first time.

Thanks to the few guys that sacrificed their planes in the process of isolating some potential elevator issues, when flown at high speed. We are grand daughter sitting or I would finish it tonight and fly tomorrow. This is the first plane that I ever assembled and changed my mind from bad to good.

Maiden will have to be in two weeks, going to AZ next weekend.
That`s all good and everything, but I have a question.

Who are you and what have you done with Al?
Jun 02, 2012, 07:05 PM
Watt me worry?
Madmax1965's Avatar
Heh!...........^^^^^^^^^^^^^^^^^^^^^^^^^
Al-----ien abduction


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Cool New HET L-39 90mm by EJF.com AceMigKiller Electric Ducted Fan Jet Talk 706 Mar 09, 2015 07:37 PM
Sold Crazy Price Drop!! HET Super Sniper with 70mm Mega/HET power system and servos. airmcn_3 Aircraft - Electric - Jets (FS/W) 9 Nov 14, 2011 11:37 AM
Found HET Sniper 90mm, airframe and maybe servos Knife Liddle Aircraft - Electric - Jets (FS/W) 2 Oct 01, 2011 11:10 AM
Sold NIB HET Super Sniper 90 V3 with HET 90mm fan and HET 600-37 motor mcgoughman Aircraft - Electric - Jets (FS/W) 0 Aug 30, 2011 08:35 PM
Sold HET All Composite Super Sniper priscalex Aircraft - Electric - Jets (FS/W) 0 Jun 30, 2008 09:17 PM