Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Nov 06, 2011, 07:51 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Discussion

12mm Prototype Props


I made these little 12mm props. They accept a 1mm shaft. If anyone is interested, follow the links below.

These are experimental props. You must understand that they might not work as expected.


Thanks


EDIT:
The new props can be found here.
Last edited by boredom.is.me; Nov 06, 2011 at 04:37 PM.
Sign up now
to remove ads between posts
Old Nov 06, 2011, 01:43 PM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
For me I would mod to achieve 35 to 45k unloaded.
Rake (concentrated thrust cone)and less tongue for more rpm at wot.
How hard is the plastic? Great effort Kev!!
Old Nov 06, 2011, 02:05 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
How is this?
Old Nov 06, 2011, 02:24 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
New prop
Old Nov 06, 2011, 02:29 PM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
Here redo showing rake and less tongue based on this new design.
Old Nov 06, 2011, 02:32 PM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
Need lil tongue for out of the hole and bite in the corners on the straights not so much tongue on the low pitch end is just drag at wot but for over all performance its best.
Old Nov 06, 2011, 03:49 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Changes made. The olds are the the top and right.
Old Nov 06, 2011, 05:27 PM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
Yes that will do, the bottom three bladed in the middle - prop blade on the left side looks spot on.
Old Nov 06, 2011, 05:33 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Great, thanks for the help.

12mm Racing Props (16 Pack)
Old Nov 06, 2011, 06:07 PM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
You've done it.. I will be buying these thank you Kevon. Will try in a little 7in outrigger on 2S.
Old Nov 06, 2011, 06:16 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Thanks, just remember what I said in my first post: EXPERIMENTAL.
Old Nov 07, 2011, 12:17 AM
Amp Abuser is offline
Find More Posts by Amp Abuser
Registered User
Amp Abuser's Avatar
What sort of rpm do you think this type of plastic can manage? I figure should be good for over 35k do to the low weight and drag of the hulls.
Old Nov 07, 2011, 12:31 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I have no idea. I do know that a prop strike will break them though. The plastic is very rigid, and with rigidity comes fragility.

I slipped while trimming down an 22mm rotor. All six blades sheared off leaving just the hub. Those were .3mm though and had less support (for lack of a better word).
Old Nov 07, 2011, 05:04 AM
zue is offline
zue
Find More Posts by zue
zue
Registered User
Quote:
Originally Posted by boredom.is.me View Post
Thanks, just remember what I said in my first post: EXPERIMENTAL.
I already bought it
Old Nov 16, 2011, 03:32 PM
GILL RC is offline
Find More Posts by GILL RC
GILL
GILL RC's Avatar
I just ordered some to play with.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale Feigao 12mm brushless motor for 40mm fan speleopower Aircraft - Electric - Jets (FS/W) 2 Sep 05, 2011 11:12 AM
For Sale Hyperion 12mm Inrunner, Thunderbird 9 ESC, 2s Lipo, Gearbox, & Props dfalcon Aircraft - Electric - Power Systems (FS/W) 6 Mar 25, 2010 03:29 PM
Sold Medusa 12mm 4000kv with Thunderbird 9 & Props soar-iowa Aircraft - Electric - Power Systems (FS/W) 2 Jan 12, 2009 10:36 PM
Discussion Of canards and pusher props... (new Barracuda canard prototype) Rusty-Gunn Foamies (Scratchbuilt) 30 Mar 02, 2008 11:23 AM
Question APC props on 12mm adapter Andy W Power Systems 11 Jan 14, 2007 10:47 PM