Shop our Airplanes Products Drone Products Sales
Thread Tools
Apr 19, 2012, 11:42 PM
Registered User
Donnyv's Avatar
weird motor fail solved!! obviously the eagle n6 doesn't like all of my esc's grounds hooked up except for one! Looks like the high current from a battery through the ESC wires was shifting the ground level of an ESC a bit in regards to the board! I think the ESC was receiving shift and noise from the pwm signal!! just a guess! but everything is working good now!!


update! bad soldering...
Last edited by Donnyv; Apr 25, 2012 at 02:00 AM.
Sign up now
to remove ads between posts
May 04, 2012, 09:54 PM
Registered User
could anyone help me my yaw is very low responce when i full it to the left(yaw) is increases altitude
May 05, 2012, 06:22 AM
Registered User
TheFlyingRookie's Avatar
Quote:
Originally Posted by zandamandag View Post
could anyone help me my yaw is very low responce when i full it to the left(yaw) is increases altitude
I got the same exact problem on my Y6 copter too , i wonder how i can make the YAW more responsive too ?
May 05, 2012, 06:28 AM
Registered User
onlyifamppowered's Avatar
I have the eagle board in a quad and in a tri. The quad can be made faster on yaw by going to aero mode and then use your TX to dull down the roll and pitch. Works well enough for me. I have noticed that after using eagle, HK clones and multiwii that they are the worst of the lot. Good and simple to set up but even a$15 hk board will be a better flyer.
If you wanta good yaw build a tricopter
Tricopters rock !
just my 2 cents worth
Rob
May 05, 2012, 02:21 PM
Registered User
Quote:
Originally Posted by TheFlyingRookie View Post
I got the same exact problem on my Y6 copter too , i wonder how i can make the YAW more responsive too ?
Set some expo on yaw and maybe more then 100% sticks travel.
May 10, 2012, 05:34 AM
Registered User
Quote:
Originally Posted by TheFlyingRookie View Post
I got the same exact problem on my Y6 copter too , i wonder how i can make the YAW more responsive too ?
its ok now try to check the motor if it spin in correct direction
May 10, 2012, 05:35 AM
Registered User
can anyone help my
when i put my gopro and fpv setup on my tricopteri got only 2 minutes of flying then i get off mygopro and fpv i got 4 minutes why?
do i need to change my lipo
my setup is
3 x fms 20a esc
3 x bumblebee 930kv
1 x 3s 2200mah 30c
May 14, 2012, 02:44 PM
Registered User
hi can anyone help me to set up my EAGLE MULTICOPTER CONTROLLER N6 to a futaba sky sports transmitter please
May 14, 2012, 04:57 PM
No you cant fly it.
kicekilla's Avatar
Quote:
Originally Posted by zandamandag View Post
can anyone help my
when i put my gopro and fpv setup on my tricopteri got only 2 minutes of flying then i get off mygopro and fpv i got 4 minutes why?
do i need to change my lipo
my setup is
3 x fms 20a esc
3 x bumblebee 930kv
1 x 3s 2200mah 30c
sure sounds like you are way too heavy. 4 minutes of flight is pretty poor anyway. where is your throttle stick at when you hover with and without fpv gear. what size props are uou using? you can use a bigger battery for longer flight times, but it sounds like you need to do something other than just change battery size.
May 28, 2012, 04:16 AM
OpenAeroVTOL developer
HappySundays's Avatar
Hey, HobbyKing are selling this now for $19.99 lol. Details here.
May 28, 2012, 06:32 PM
Registered User

EAGLE N6 Multicopter Controller Update Firmware


Hey Guy's

Is there anywhere that there is updated firmware for the EAGLE N6 Multicopter Controller? The Hobbyking i86 Multi-Rotor Control Board looks to be the same as the eagle N6 Control Board. I also see the is there EAGLE N6 V2 Multicopter Controller.

The Hobbyking i86 Multi-Rotor Control Board have sold out already, over 100 + last night and now into the -15 "WOW" that was quick

Barry
May 28, 2012, 06:58 PM
OpenAeroVTOL developer
HappySundays's Avatar
Ah, well there you go - it's an Eagle N6 V1 clone.
The V2 seems to have an external crystal oscillator.
I wished HK had copied the V2...
May 29, 2012, 11:31 PM
Registered User
onlyifamppowered's Avatar
How long before you have the board hacked and better code written for it happy ???
May 30, 2012, 12:19 AM
Registered User
Is it worth trying to add a small 16Mhz crystal to the HK i86 board, or would the timing break?
May 30, 2012, 06:36 AM
OpenAeroVTOL developer
HappySundays's Avatar
Quote:
Originally Posted by onlyifamppowered View Post
How long before you have the board hacked and better code written for it happy ???
Haha... Well I will get my boards any day now. Hopefully that switch bank has not used up something I need for the LCD or GUI interface..

Quote:
Originally Posted by Erknie View Post
Is it worth trying to add a small 16Mhz crystal to the HK i86 board, or would the timing break?
On a traditional KK board the two oscillator pins were connected to the LED and RUDDER input (shrugs) but who knows how the I/O has been mapped for this board. It would sure help with GUI timing issues.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Multicopter Flight Controller Comparison Chart mbsteed Multirotor Drone Talk 27 Jun 13, 2015 09:41 AM
Wanted KK Plus V5.5d Multicopter controller Art Newland Aircraft - Electric - Multirotor (FS/W) 0 Sep 08, 2011 02:02 PM
Discussion Wanted -- KK Multicopter controller // XX Controller Chris Moon Multirotor Drone Talk 0 Feb 07, 2011 10:21 AM
Sold 6061 Tricopter w/KK-Multicopter Controller Techcoder FPV Equipment (FS/W) 0 Jan 22, 2011 11:55 AM
Discussion Recommended Multicopter controller board? DENHAMDULAKE Aerial Photography 1 Nov 20, 2010 06:58 AM