AQ50D PRO revision for Quad , Hexa and Okto - Page 66 - RC Groups
Thread Tools
Jun 15, 2012, 08:19 AM
Suspended Account
It is probably the previous version of the board, before the newly released one with the embedded sensors so you should be fine I suspect.
Sign up now
to remove ads between posts
Jun 15, 2012, 10:33 AM
Advanced Monkey
nebstress's Avatar
Quote:
Originally Posted by skipper1
Thank you.
Since I have installed the other software's, how can I delete them? I have searched everywhere for a manual or proper procedures and cannot find anything except on this forum.
Since the DS-Sensor works on both AQ50D & AQ50 Pro, there needs to be information on what works on what.
I wrote to Infinity-Hobby and they were confused about what I installed. Here is what they said;
We are a bit confused by your message. The firmware for AQ50 Pro (TMF Pro) with new sensor should be TMF_AQ50D-S(V5.2).tmf which can be downloaded from the following link :
http://www.infinity-hobby.com/main/d...0D-S(V5.2).tmf

You will need to upgrade the firmware of TMF Pro first before install the AQ50D-S.

We are not sure where you got the firmwares listed in your message and what those 1)~4) meant. Can you advise further detail?
You don't need to delete them, simply re-install the correct firmware & that is it.
Jun 15, 2012, 05:30 PM
Registered User
Hi guys!

Add-on first test out of my garden!!!

Sainte Victoire Summer Time !!! (2 min 13 sec)


I have some vibrations on the motors, I have 10" props now, I think it was better with 9"...

Gain is pretty low, position 3 ....

It needs a few tweaks!
Jun 15, 2012, 05:56 PM
Advanced Monkey
nebstress's Avatar

TMF Boards


Name: TMF Boards.jpg
Views: 132
Size: 68.0 KB
Description:
Jun 17, 2012, 06:02 AM
Alicante, Espaņa
Hello everybody,

I just went to fly yesterday for first time in my life with a quadcopter and the TMF-pro board, the software is 1.5.

After some triming at the flying field and changing the transmiter dual rate for the throtle, elevator and ailerons, i was able to fly very well for 5-6 times. Without any previous experience!!.

I am very happy, but I have some doubts:

I bought the new AQ50d-S DS-sensor add on, that should be here in 2-3 days.

So, what firmware (.tmf) should I use?.

What's the difference betwin 2G and 6G?

Do I have to make the R21-R19 mod in the board with this new add on sensor?

Thank you all for your help.
Jun 17, 2012, 06:36 AM
Advanced Monkey
nebstress's Avatar
Quote:
Originally Posted by catamar
Hello everybody,

I just went to fly yesterday for first time in my life with a quadcopter and the TMF-pro board, the software is 1.5.

After some triming at the flying field and changing the transmiter dual rate for the throtle, elevator and ailerons, i was able to fly very well for 5-6 times. Without any previous experience!!.

I am very happy, but I have some doubts:

I bought the new AQ50d-S DS-sensor add on, that should be here in 2-3 days.

So, what firmware (.tmf) should I use?.

What's the difference betwin 2G and 6G?

Do I have to make the R21-R19 mod in the board with this new add on sensor?

Thank you all for your help.
Hi catamar, When you have the new add-on sensor installed you need to use firmware with "Add-on" in its name, ie:- "TMF_Digital_v5.6_Add-on".

You don't mention which you have, 2G or 6G?
Jun 17, 2012, 06:58 AM
Alicante, Espaņa
How do I know which I have?

Quote:
Originally Posted by nebstress
Hi catamar, When you have the new add-on sensor installed you need to use firmware with "Add-on" in its name, ie:- "TMF_Digital_v5.6_Add-on".

You don't mention which you have, 2G or 6G?
Jun 17, 2012, 07:29 AM
Advanced Monkey
nebstress's Avatar
Quote:
Originally Posted by catamar
How do I know which I have?
It will say in the GUI under the Firmware version.
Name: Capture.jpg
Views: 149
Size: 59.0 KB
Description:
Jun 17, 2012, 08:14 AM
Alicante, Espaņa
Ok, I have the G2.

Quote:
Originally Posted by nebstress
It will say in the GUI under the Firmware version.
Attachment 4944347
Jun 17, 2012, 08:36 AM
Advanced Monkey
nebstress's Avatar
Quote:
Originally Posted by catamar
Ok, I have the G2.
OK, that's fine no mod need!

Just use the 5.6 add-on firmware when you get your new Sensor.

I noticed that you are using FW 1.5 at the moment, you can update that to the new 1.8 2G firmware if you like (TMF_Pro_v1.8_2G).
Jun 17, 2012, 09:00 AM
Alicante, Espaņa
Ok, thank you very much. It's good to know that I don't have to make the board mod.
I am a little afraid of changing to v1.8_2g, because the quad flights so well now, that I am afraid of changing anything

I will have to change with the add-on, but before that, I am not sure to change anything.

Quote:
Originally Posted by nebstress
OK, that's fine no mod need!

Just use the 5.6 add-on firmware when you get your new Sensor.

I noticed that you are using FW 1.5 at the moment, you can update that to the new 1.8 2G firmware if you like (TMF_Pro_v1.8_2G).
Jun 17, 2012, 10:01 PM
Registered User
when use the DS-sensor,the old sensor in board is no work.
Jun 18, 2012, 02:42 AM
Alicante, Espaņa
Must be amazing to fly with this new sensor, because for me was very easy to fly my quad without any previous experience, the first day.
Jun 18, 2012, 02:43 AM
Alicante, Espaņa
So, any idea on when the height sensor will be ready to buy?. And the gps system?
Jun 18, 2012, 09:20 PM
Registered User
video by peter13312
Hexacopter gopro 2 (1 min 50 sec)


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Poll What Motors do you use on your tri/quad/hexa/octal etc? bob4432 Multirotor Drone Talk 4 Aug 29, 2010 08:10 PM
Sold MicroKopter ARF Quad/Hexa G-unit Aircraft - Electric - Helis (FS/W) 3 Aug 23, 2010 10:38 AM
Discussion Folding frame for AP - tri, quad, Hexa, Okto danielpetrescu Multirotor Drone Talk 9 May 10, 2010 01:25 AM
Question Tri/hexa-copter or Quad/Octa-copter and Spartan AP2000i or Helicommand Arthur P. VTOLs 2 May 20, 2007 04:02 PM