Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Dec 04, 2011, 06:51 PM
Gregor99 is offline
Find More Posts by Gregor99
Revolectrix Ambassador
Quote:
Originally Posted by Komet ME163 View Post
Was wired right on pl6 side but wrong on paraboard side. Reversed all wires and charger
So the pins going into the paraboard were reversed (red going to where black should go and vise versa?). Did you just remove all pins and re-insert them in the correct order? Do let us know what Dave says.If there a few reversed cables out there, it'd be good to have the heads up.
Sign up now
to remove ads between posts
Old Dec 04, 2011, 07:16 PM
Komet ME163 is online now
Find More Posts by Komet ME163
Registered User
Komet ME163's Avatar
yea i pulled all the wires and reinstalled with para board connector flipped. It was progressive rc brand PL8 adapter cable p/n: ac-pl8pcb. I will call progressive tommorrow and let them know to check them. Once again thanks for your help, as your troubleshooting suggestions helped me to find the problem.

Bill
Old Dec 05, 2011, 06:47 PM
write2dgray is offline
Find More Posts by write2dgray
write2dgray's Avatar
Looks like a couple of cables were swapped up - you received the balance board to PL8/PL6 cable, not the parallel charge board to PL8/PL6 cable. The mistake was certainly on our part and I apologize for the inconvenience, I believe we've gotten everyone sorted out and please let me know if you ever need anything else at all.

Cheers,
David
ProgressiveRC
Site Sponsor
Old Dec 05, 2011, 11:47 PM
teeforb is offline
Find More Posts by teeforb
Registered User
Hey Tim, I just got the replacement of the pl6. On the replacement, no big deal, but it seems that the film inside of the LCD screen is peeling. I can see part of the film is attached to the charger skin and other parts of the film is touching the LCD part. Kinda hard to explain. If u know what im talking about, is this normal?
Old Dec 06, 2011, 09:06 AM
teookie is offline
Find More Posts by teookie
Perfect 3pt inverted landing!
teookie's Avatar
Quote:
Originally Posted by teeforb View Post
Hey Tim, I just got the replacement of the pl6. On the replacement, no big deal, but it seems that the film inside of the LCD screen is peeling. I can see part of the film is attached to the charger skin and other parts of the film is touching the LCD part. Kinda hard to explain. If u know what im talking about, is this normal?
Power it up. Does the screen still look as your describing? On mine the label appears to be stuck to the LCD in the center but not at the edges. Once the backlight is on though you cant tell. It's just a cosmetic issue so I am not worried about it.

Love my PL6. Thanks FMA for making it every bit as awesome as the PL8.
Old Dec 06, 2011, 10:49 AM
teeforb is offline
Find More Posts by teeforb
Registered User
Quote:
Originally Posted by teookie View Post
Power it up. Does the screen still look as your describing? On mine the label appears to be stuck to the LCD in the center but not at the edges. Once the backlight is on though you cant tell. It's just a cosmetic issue so I am not worried about it.

Love my PL6. Thanks FMA for making it every bit as awesome as the PL8.
Just checking! Thanks bro!
Old Dec 06, 2011, 12:08 PM
teeforb is offline
Find More Posts by teeforb
Registered User
does ccs supports Windows XP? and if yes, for how much longer?

thx
Old Dec 06, 2011, 12:39 PM
Tim Marks is offline
Find More Posts by Tim Marks
President, FMA, Inc.
Tim Marks's Avatar
Quote:
Originally Posted by teeforb View Post
does ccs supports Windows XP? and if yes, for how much longer?

thx
Hi:

Yes, even Win 2000 still. For how long, can't say. That depends on MS to a large extent. I know support for Win XP doesn't end until like 2014, but it's likely to be several years beyong that before .NET can't support such an old O.S. A lot can change looking ahead that far.

Tim Marks
Old Dec 06, 2011, 12:43 PM
teeforb is offline
Find More Posts by teeforb
Registered User
i see.. im asking because im thinking of picking up a cheap, used netbook only for RC application like FMA CCS, tekin sw, castle, lrp, etc... most used netbooks has XP
Old Dec 13, 2011, 02:53 AM
psionic619 is offline
Find More Posts by psionic619
Registered User
lets say i put charge rate at 10 amps and i select charging 2 parallel will the amp bump up to 20 or stay at 10 amps while charging 2 packs in parallel? thanks in advance
Old Dec 13, 2011, 04:42 AM
ggcrandall1 is offline
Find More Posts by ggcrandall1
Registered User
ggcrandall1's Avatar
Quote:
Originally Posted by psionic619 View Post
lets say i put charge rate at 10 amps and i select charging 2 parallel will the amp bump up to 20 or stay at 10 amps while charging 2 packs in parallel? thanks in advance
The charger will increase the current by the number of packs in parallel.

Glen
Old Dec 13, 2011, 07:28 PM
psionic619 is offline
Find More Posts by psionic619
Registered User
Quote:
Originally Posted by ggcrandall1 View Post
The charger will increase the current by the number of packs in parallel.

Glen
thank you
Old Dec 13, 2011, 08:44 PM
Pescador is offline
Find More Posts by Pescador
Boat racing enthusiast
Pescador's Avatar
I just received my Powerlab 6 from Revo with 2 paraboards and rebuilt my charger case with a 24v power supply.
The software is installed and everything is working great on XP, quite an upgrade from my old Bantams.
One question though can I go a little longer on the USB maybe 5ft instead of the usual 3ft or would it be a problem?
Old Dec 13, 2011, 09:07 PM
ggcrandall1 is offline
Find More Posts by ggcrandall1
Registered User
ggcrandall1's Avatar
I think Tim reported earlier that lengthening the USB cable is no problem.

Glen
Old Dec 13, 2011, 09:42 PM
Tim Marks is offline
Find More Posts by Tim Marks
President, FMA, Inc.
Tim Marks's Avatar
This is correct:

Quote:
Originally Posted by ggcrandall1 View Post
I think Tim reported earlier that lengthening the USB cable is no problem.

Glen
Tim Marks


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Sneak Peek at the NEW Cellpro PowerLab 8 (v2) Tim Marks FMA Direct 6544 Yesterday 01:03 PM
New Product Introducing the ALL NEW Cellpro 10XP Charger Howard Matos FMA Direct 448 Oct 26, 2016 04:58 PM
New Product Introducing the Scirocco--All Molded, All Carbon Pitcheron Ward Hagaman Slope 180 Oct 04, 2014 10:43 AM
Sold Revolectrix/FMA direct Cellpro PowerLab 8 unused new thwang99 Aircraft - Electric - Batteries & Chargers (FS/W) 2 Aug 26, 2010 04:24 PM
Wanted Cellpro 4S 4amp Charger-New Version ( Found One--Thanks! ) helinut4ever Aircraft - Electric - Batteries & Chargers (FS/W) 1 Jan 27, 2009 05:24 PM