Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Nov 23, 2012, 03:33 PM
MATIN is online now
Find More Posts by MATIN
Just Toss It !!!
MATIN's Avatar
Like I said before. I have one word for you: Silicone.
Sign up now
to remove ads between posts
Old Nov 23, 2012, 05:16 PM
bluffman is offline
Find More Posts by bluffman
Registered User
bluffman's Avatar
shower eschion
Old Nov 23, 2012, 05:35 PM
slopeiron is offline
Find More Posts by slopeiron
No fuse too fat
slopeiron's Avatar
Maybe if you put your plug in the bottom of a paper cup so that the resin can fill over the top of it?
Old Nov 24, 2012, 04:40 AM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar

I got this.


1 down, 11 to go
Old Nov 26, 2012, 11:31 AM
Artsloper is offline
Find More Posts by Artsloper
The ProCreator
Artsloper's Avatar
Hey Paul, I've done this before but with bondo and WD40. Spray the mold with the WD then "drizzle" in the bondo. By "drizzle" I mean run the bondo from one side of the mold and let gravity pull the bondo in. This way you get no air trapped in your mold. Then just pop it out when it sets.
Old Nov 26, 2012, 10:09 PM
RAFster is offline
Find More Posts by RAFster
Registered User
Since WD40 has silicone won't it cause lots of paint adhesion problems on the molded parts?
Old Nov 26, 2012, 11:20 PM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar

you tell me this NOW !?....


whats the best way to bond resin to wood ?
Old Nov 26, 2012, 11:36 PM
RAFster is offline
Find More Posts by RAFster
Registered User
Just saw the earlier message...sorry Dutchy.
Mechanical bond is improved if it has something to key and lock it in place. A few small holes in wood will improve grip and the hidden side of the resin can have a few angled holes that can improve glue adhering to resin. But, it will be weaker joint. No water and polyurethane glue (gorilla/probond) will give good strength, just clean off any squeeze out for easier finishing.
Old Nov 27, 2012, 11:31 PM
markktm is offline
Find More Posts by markktm
only easy day was yesterday
markktm's Avatar
from the looks of the popcycle sticks you need a sraigtht slot in the side of the fuse for easy alignment. If all the sticks are straight in the exhausts.

mark
Old Dec 01, 2012, 07:08 PM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar

yes ? no ? maybe ?...


huummm......
Old Dec 01, 2012, 07:25 PM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar

molly...


seems unconcerned
Old Dec 01, 2012, 10:27 PM
slopeiron is offline
Find More Posts by slopeiron
No fuse too fat
slopeiron's Avatar
I like it!
Old Dec 01, 2012, 10:47 PM
MATIN is online now
Find More Posts by MATIN
Just Toss It !!!
MATIN's Avatar
Higher.
Old Dec 01, 2012, 11:31 PM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar

"higher"


SO Demanding !
Old Dec 01, 2012, 11:58 PM
dutchydawg1 is offline
Find More Posts by dutchydawg1
Registered User
dutchydawg1's Avatar
I don't think it will "pull" out of the mold ?...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Warning Beware connorryder100 deerfreak Trader Talk 47 Jan 12, 2011 06:56 AM
Off Site warning beware of this buyer abletowinginc Aircraft - Electric - Jets (FS/W) 30 Aug 14, 2010 01:21 PM
Alert "WARNING DX 7 LOCK OUT BEWARE" Yakman13 Radios 46 May 28, 2007 10:03 PM
Discussion Servocity warning! Buyer Beware Alkaline Vendor Talk 41 Feb 11, 2006 12:16 AM
warning watch out Gws Radio System Forsale buyer beware!!! chris-miranda Aircraft - Electric - Airplanes (FS/W) 5 Sep 03, 2003 11:55 PM