Thread Tools
Jun 10, 2012, 10:07 PM
Registered User
SethPenery's Avatar
It's gonna look sweet what ever direction you go with it Paul. Nice work dude. I'm getting inspired and learning a lot watching you. Keep up the good work.
Sign up now
to remove ads between posts
Jun 10, 2012, 10:45 PM
Registered User
dutchydawg1's Avatar

molly.


ever feel like someone is "watching" you ?......
Jun 11, 2012, 12:14 AM
Registered User
dutchydawg1's Avatar

did I get the "look" ?


I think I need the blisters .....
Jun 11, 2012, 09:08 AM
No fuse too fat
slopeiron's Avatar
Yeah! I like that front view! Looks just like the 109. Blisters would add some nice detail too.

So, I'll just throw this in and you can decide - If I was going to do it again, I would mold those separately and glue them on after. The reason is that there isn't much radius where the blisters meet the fuse, so that means a sharp corner in the mold. They make a little pocket that the cloth just doesn't want to lay down into nicely and I'm always fighting bubbles there. Of course, you can put cabosil in that area and that's what I do. But the cabosil can get squished out during layup and it seems like it's always a problem area. They are pretty far back on the fuse, so having a separate piece glued on there should not interfere with the hatch. The disadvantage is that it would be an additional layup to do, but it would be a very small and simple part.
Jun 11, 2012, 09:31 PM
closed due to popular demand
...
Last edited by ibuild; Oct 19, 2013 at 02:38 PM.
Jun 11, 2012, 09:37 PM
Registered User
dutchydawg1's Avatar
whats cotton "flock" ?.... cotton balls ?
Jun 11, 2012, 11:37 PM
Just Toss It !!!
MATIN's Avatar
What the flock?!
Jun 11, 2012, 11:47 PM
Nothing to see here...
67econoline's Avatar
Don't .....


FLOCK it all up...!!!

Rubio
Jun 12, 2012, 05:54 AM
closed due to popular demand
...
Last edited by ibuild; Oct 19, 2013 at 02:39 PM.
Jun 12, 2012, 08:31 AM
No fuse too fat
slopeiron's Avatar
Cotton flock would probably work better than cabosil because it would be less likely to squish back out through the cloth.
Jun 12, 2012, 11:37 AM
Just fly it!
wyowindworks's Avatar
Actually, the resin will run right out of cotton flock. Typically, you need to add some cab-o-sil to a cotton flock mix to prevent this. The best way to prevent it from moving around it to increase the viscosity of the sploog.

Looking good, Dutchy!
Jun 24, 2012, 11:41 PM
Registered User
dutchydawg1's Avatar

gun blisters.


I'm glueing the 2 blisters together so I can attempt to keep them symetrical
Jun 24, 2012, 11:42 PM
Registered User
dutchydawg1's Avatar

gun blisters 2


"parts"
Jun 24, 2012, 11:44 PM
Registered User
dutchydawg1's Avatar

huummm....


....... 2 thumbs down on the blisters ......
Jun 24, 2012, 11:47 PM
The ProCreator
Artsloper's Avatar
I say go with the gun cover off the 190-D.

Here's a quarter, get a rat to chew that mole off your face (0 min 14 sec)


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Warning Beware connorryder100 deerfreak Trader Talk 47 Jan 12, 2011 05:56 AM
Off Site warning beware of this buyer abletowinginc Aircraft - Electric - Jets (FS/W) 30 Aug 14, 2010 12:21 PM
Alert "WARNING DX 7 LOCK OUT BEWARE" Yakman13 Radios 46 May 28, 2007 09:03 PM
Discussion Servocity warning! Buyer Beware Alkaline Vendor Talk 41 Feb 10, 2006 11:16 PM
warning watch out Gws Radio System Forsale buyer beware!!! chris-miranda Aircraft - Electric - Airplanes (FS/W) 5 Sep 03, 2003 10:55 PM