Thread Tools
This thread is privately moderated by Chrizz, who may elect to delete unwanted replies.
Oct 03, 2011, 09:51 PM
Registered User
Chrizz's Avatar
Gallery

Ultra Micro Dead Simple Wing



Name: 1.jpg
Views: 258
Size: 161.7 KB
Description: Name: thumb-DSWing.jpg
Views: 235
Size: 5.2 KB
Description:
Plans are from: https://www.rcgroups.com/forums/show....php?t=1252282
(does not include the profile fuselage)

Name: 2.jpg
Views: 235
Size: 138.7 KB
Description: Name: 5.jpg
Views: 167
Size: 80.7 KB
Description: Name: 3.jpg
Views: 170
Size: 127.8 KB
Description:

The wing and winglets are made of 3mm Depron, the profile fuselage of 6mm Depron.
The wings leading edge and the nose have been covered with clear tape.

The electronics come from a Parkzone Ultra Micro Sukhoi.

Name: 4.jpg
Views: 175
Size: 97.0 KB
Description: Name: 6.jpg
Views: 173
Size: 70.8 KB
Description:

The Dead Simple Wing lives up to its name!
It is in fact extremely simple to build and very easy to fly.
The construction is nothing to talk about and i imagine that it could be customized
in various ways or used as a platform for other builds. It is dead simple.
In flight it is just as simple and flawless. Once in the air, when put on a trajectory, it flies like on rails.
Turns are clean and can be large and gentle or very tight. There's no sign of any bad tendencies.
The control surfaces responses are quick and precise around the center, even with a lot of travel.
Roll rate is satisfying, about 1 roll per sec..
Max flying speed seems about the same as with U.M. Sukhoi, but the wing accepts to fly pretty slow to.

Name: 7.jpg
Views: 197
Size: 191.6 KB
Description: Name: 8.jpg
Views: 161
Size: 125.3 KB
Description: Name: 9.jpg
Views: 159
Size: 77.3 KB
Description:
Last edited by Chrizz; Jan 17, 2016 at 12:36 PM.
Sign up now
to remove ads between posts
Dec 01, 2011, 08:47 PM
Registered User
nice you have does a nice job on then
Feb 19, 2012, 07:31 PM
Registered User
numanair's Avatar
Nice. Could you explain how you did the torque rods? I'm trying to figure out a good way to make the part where the pushrod and torque rod meet.
Feb 21, 2012, 07:18 AM
Registered User
Chrizz's Avatar
Hi Numanair! Thanks!
The torsion bars and pushrods are linked together with heatshrink and a drop of CA. The heatshrink allows for enough mouvement while not presenting any slack.
To obtain enough travel at the elevons, I've shortened the torsion bars a little. It's important that the torsion bars/pushrods/elevons move freely, before connecting them to the servos. It's too easy to obtain different travels, when you compare the two elevons travel at different points...
Hope this does help you? Don't hesitate to ask if there's anything else!

Happy landings :-)
Last edited by Chrizz; Feb 21, 2012 at 07:00 PM.
Oct 10, 2014, 05:46 PM
Registered User
hey could you tell me your dimensions 24 seems big for micro gear
Oct 11, 2014, 06:44 AM
Registered User
Chrizz's Avatar
Quote:
Originally Posted by jh1985
hey could you tell me your dimensions 24 seems big for micro gear
Hi!!

Yes 24" is way to large for this Ultra Micro gear, I did scale the plan down to just under 40cm.
Here's another version of the plan with different scales added: the original 24" (60,96cm), 39.84cm e.c.t ...
Name: Dead Simple Wing - plan, inch + cm.jpg
Views: 58
Size: 110.4 KB
Description:

Happy landings :-)

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion 24" DS (Dead Simple) Flying Wing - Pics, Video, Plans forlack Foamies (Scratchbuilt) 813 Apr 10, 2017 07:21 AM
Build Log Heavy lifter Dead Simple Wing Ottomite Flying Wings 5 Jul 24, 2011 11:56 AM
Question Jerbear's Simple Wing Flyboy Steve Foamies (Scratchbuilt) 8 Apr 05, 2011 10:03 PM
Discussion Simple SK membrane wing isn't simple ..at all !!!??:) khaled_abobakr Ornithopters 7 Apr 04, 2011 05:29 PM
Discussion Simple wing design? Autotechwagon SPAD - Simple Plastic Airplane Designs 8 Mar 14, 2011 01:45 AM