OK I think we need a thread dedicated to Wookong-M settings,Pics, Vids etc.. The other thread, the info is all over the place. This thread will have dedicated sections for vids,pics,settings,etc.... Hopefully the dealers and manufacturer will also help with tech support here. This will make it much easier for guys to know what works and what doesnt and see proven rigs and the settings used.

Pics:

Vids:
VIDEO Of SETUP #1

October8.wmv (3 min 9 sec)

DJI WK-M new gimbal test (2 min 27 sec)

VIDEOS OF SETUP #2

Droidworx SkyJib 8 with Wookong FC (NOW FOR SALE) (3 min 22 sec)

http://www.vimeo.com/29288017 HH & GPS LOCK VIDEO

DJI Wookong-M w/Height Hold & GPS LOCK Activated For AP Aerial Photography (3 min 49 sec)

VIDEO OF SETUP #3
RAW ONBOARD VIDEO:
Vid#1
http://sprealinvest.at/firstWKMirrsee.mov
Vid#2

DJI WKM on a RC carbon 900 mm Hexa (5 min 0 sec)

Better Quality Vid#2-> http://sprealinvest.at/secondWKMirrsee.mov


VIDEO OF SETUP #5:

WK-M and $12 cheapo wood frame after abused by 4 males at IRCHA (3 min 16 sec)

Setup & Settings:

SETUP #1

This setup was used in the vid "Nex5NonWKMHex.wmv"
Setup:
28" motor to motor
Motors-Avroto 2814-11
ESC-DYS 30 amp
Graupner 11 x 5 props
Dual 4S 5000mah in parallel
Photohigher AV130 old style with Hyperion servos
JR 11X tx with R921 rx
Rusty's Rev8 frame
Droidworx landing gear
Camera-Sony NEX5N

Settings:

Basic gains roll and pitch 300% Yaw at max, 300%, altitiude at max 250%

ATTI gains, 65 % pitch and roll

All other settings currently at default.

SETUP #2

Setup shown in 3rd vid:
2nd Pic in the pics section:

Frame-Droidworx Skyjib8 Octocopter
ESC-Hobbywing Fentium 80A
Motors-Axi 4120/20
Props-APC 14 x 4.7
Camera 5D
Weight without cam is over 5.5 Kilos

Settings:

Basic Gains: 175,125,175,75
Attitude: 65,65

SETUP #3

Frame-RC Carbon 900mm Hexa,
Motors-Axi 2820/14
ESC-Plush Turnigy 40a
Props-Carbon Props 12x3.8 Weight-11 grams
TX-Graupner MX-22 with RASST Robbe Model
RX-Futuba R6208 SB Receiver, using S-bus
Cam Mount-AV 130 new Savöx servos
Camera-Canon 500D 10-22mm lens about 900 grams
Batt-Nano Tech 6000 mah 4s

SETTINGS:
Basic Gains: 170
Attitude:90

SETUP #4:

Motors-Avroto 2814's
Props-Graupner Electro 11x5 props
ESC-Turnigy Plush 30 ESC's
Frame-Modified RC Carbon Frame and Gear
RX-Spektrum 9010X Receiver
Batts-Dual 4S 5000 Packs
Cam Gimbal-RC Carbon Gimbal

SETUP #5:

Size-480mm motor to motor CHEAPO wood frame
Motors-1150 kv 3S
8" props
ESC-30A HobbyWing
GoPro hard mounted(No cam mount)

SETTINGS:
Basic 130, 130, 220, 110
Atti 140, 140
ESC Timing-Low

SETUP #6:

Frame-Coptersky 500mm folding quad frame
Cam Mount-CopterSky GoPro 2 axis camera mount
Motors-RC Timer 2830/14 motors
ESC-Turnigy Plush 30A escs
Batts-2x3S 2460mAh (I may go to a single 4S 4000mAh later)
2S 1000mAh for the video tX
FPV Setup-200mw 5.8ghz video transmitter

Downloads:

MISC:

Advance parameter tuning-

“I” value
Better left alone, it is mainly for forward flight with head wind. Increase for strong head wind. Decrease for strong tail wind.

“V Damping” value
Ascending and descending braking, as to how fast you want the multi to stop. Increase value to have fast braking.

“Disturb Gain” value
Increase to have higher position hold; decrease to have less. Fine tuning between ATTi and GPS modes in position hold.

All advance parameters are only good in GPS mode.

When others post there vids,settings,pics, etc... I will copy them into the appropriate section. If anyone has any suggestions on what to put in the last reserved please suggest

Subscribed .....

Good idea, Tony. I'll be posting info, pics, etc., on my new X8 build here later this week.

-- Gary

Originally Posted by GGoodrum

Good idea, Tony. I'll be posting info, pics, etc., on my new X8 build here later this week.

-- Gary

Thanks Gary I appreciate it and will put your info in the appropriate section once posted.

Can't wait to get mine

Will be using a X650 frame with standard motor's and 4 x Hobbywing Fentium 30A ESC's

3s 3600 or 3s 4400 Lipo's

Will post more once I get it and getting setting up

not done yet, here is what setup so far

Good idea lets keep this thread clean and informational and with tried facts and findings and it will help all. Good idea Tony!
I will post photos of the 800mm Y-6 built I am working on.
Michael64

I have now started to run with the new power module, and it works great, no heat buildup coming from an ESC. Also it makes me feel safe about the battery voltage, I have in the past had the quad fall out of the sky because I was not paying attention to how long it was up, and the battery had dropped below a safe value. Now with the settings I've been using, which after looking over the battery graphs I set the values, and it comes down slowly at the very end and I still can control it where I would like it to land. The throttle settings are above neutral point but still can raise and lower it if needed and landed where I would like. Here's an example of my settings and I made to a little adjusting the first setting but so far works great.

Jerry

Here is my Y-6 in progress.

Avroto 2814's
Graupner Electro 11x5 props
Turnigy Plush 30 ESC's
Modified RC Carbon Frame and Gear
Spektrum 9010X Receiver
Dual 4S 5000 Packs
RC Carbon Gimbal for now

Michael64