Thread Tools
Old Aug 20, 2011, 03:07 PM
cyberdog is offline
Find More Posts by cyberdog
Registered User
Its a secret
Sign up now
to remove ads between posts
Old Aug 20, 2011, 11:12 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Ok Ok.. I won't ask again.. LOL

Let me know when you have a test done..!
RCG Plus Member
Old Aug 21, 2011, 02:08 AM
flyhigh300 is offline
Find More Posts by flyhigh300
Registered User
Cyberdog..

Where those motor rated for 3s ?

with smaller prop and if you don't pull to many amps.. and get it hot..
it should be ok..

But just step carefully... I thought they where rated for.. 2S


Quote:
Originally Posted by cyberdog View Post
This is 18cm mtm if i remember right. Wanted to use 5" props but the frame was too small so went with 4" propps instead Might try and fly it tomorrow if i can fit fc and rx on it Hopefully i get enough lift with the 4" props so it can take off . If not i make a new one that fits 5" props. Will be using 500-1000 mah 3s lipo.

If i cant find room for everything i will just wait till i get the real frame and try it out then
Old Aug 21, 2011, 02:16 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Flyhigh300 PM sent.
Old Aug 21, 2011, 09:03 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
I was looking to power them from 2s on my side.
Already ordered some nice NanoTech 2s battery.
RCG Plus Member
Old Aug 21, 2011, 09:18 AM
NaterPin is offline
Find More Posts by NaterPin
Registered User
what size were you thinking?
Old Aug 21, 2011, 09:22 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
I need to ask someone, i didn't make the order myself...

I think it was that one
http://www.hobbyking.com/hobbyking/s...dProduct=11900
RCG Plus Member
Old Aug 22, 2011, 12:44 AM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar
Hey here is a buddy code for motors that Im going to use on this.. so if u decide to get them to..
http://www.hobbyking.com/buddy.asp?c...E-74724AE7FE3F
ESC, http://www.hobbyking.com/buddy.asp?c...8-E8BF7CFBF7F1
and prop, http://www.hobbyking.com/buddy.asp?c...B-CD1D401022EE
Old Aug 22, 2011, 07:02 PM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar

Look what i got today


I didn't use all the hardware that came with it, instead i used some standoffs i had, I like this little guy, cant wait for my motors to come in.. and it is 2.1oz
Last edited by G-unit; Aug 22, 2011 at 07:09 PM.
Old Aug 22, 2011, 07:24 PM
forsakenrider is offline
Find More Posts by forsakenrider
I hope someone gets one of these flying soon! I have all my stuff on order...
Old Aug 22, 2011, 08:02 PM
flyhigh300 is offline
Find More Posts by flyhigh300
Registered User
G-Unit..

Good point to make..

the frame is based on the use of this board..

https://www.rcgroups.com/forums/show....php?t=1438619

they specify.. you can get with out with out.. Header Pins..

If you plant to use any of these..

http://www.multiwiicopter.com/collec...ard-v2-0-naked

http://www.multiwiicopter.com/collec...v4-0-llc-naked

I would suggest.. using.. adding some washer..

The double plate was last minute MOD, and some may find it more difficult to make it all fit.. as this is a Small frame..


Quote:
Originally Posted by G-unit View Post
I didn't use all the hardware that came with it, instead i used some standoffs i had, I like this little guy, cant wait for my motors to come in.. and it is 2.1oz
Old Aug 22, 2011, 08:06 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Wow... things are going fast..

HK have some shipping problem (BackLog i guess)...
Things where shipped yesterday..
RCG Plus Member
Old Aug 22, 2011, 09:18 PM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar
Quote:
Originally Posted by flyhigh300 View Post
G-Unit..

Good point to make..

the frame is based on the use of this board..

https://www.rcgroups.com/forums/show....php?t=1438619

they specify.. you can get with out with out.. Header Pins..

If you plant to use any of these..

http://www.multiwiicopter.com/collec...ard-v2-0-naked

http://www.multiwiicopter.com/collec...v4-0-llc-naked

I would suggest.. using.. adding some washer..

The double plate was last minute MOD, and some may find it more difficult to make it all fit.. as this is a Small frame..
I will be using the OpenPilot CC board on mine..
Old Aug 22, 2011, 09:20 PM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar
Quote:
Originally Posted by Dialfonzo View Post
Wow... things are going fast..

HK have some shipping problem (BackLog i guess)...
Things where shipped yesterday..
How long ago did u place the order??
Old Aug 22, 2011, 09:20 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Do you already have the OpenPilot CC board ?
Would like to see it on the chasis...!
RCG Plus Member


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion DiaLFonZo-Copter TrinitY Quad V2.0 Dialfonzo Multirotor Talk 316 Mar 12, 2012 05:46 AM
Build Log KX-2 V1.0 Dragon kristjane Multirotor Talk 4 Oct 06, 2011 02:16 PM
Sold TacCon FS One Hangar 9 v1.0 Controller smallmax Aircraft - General - Miscellaneous (FS/W) 4 Apr 09, 2011 10:31 PM
Discussion Easy osd v1.0 or v1.2 borsel FPV Talk 2 Jul 10, 2010 05:35 AM
Idea A nifty tool for you guys/girls that program pics etc it is ASCII V1.0.0 flyman668 DIY Electronics 5 Dec 15, 2004 01:47 AM