Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Sep 04, 2011, 11:56 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by olivierb View Post
You mean the controller to the legs side and the battery to the top side ?
Yes something like that. To have the power board and ESC under.
More for the look.. lol

Do you have a vid of your little screamer..
RCG Plus Member
Sign up now
to remove ads between posts
Old Sep 04, 2011, 12:11 PM
olivierb is offline
Find More Posts by olivierb
Registered User
Well, the legs will be in the way of the ESC and the RC connectors will be close to the ground.

No video yet, filming and flying are not compatible for my piloting skill
Old Sep 04, 2011, 01:53 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar

DiaLFonZo - QuadMini Build


Ok.. QuadMini awaiting his Receiver... !

All motor rotations are done.









Complete set of pictures in high resolution HERE
RCG Plus Member
Old Sep 05, 2011, 01:28 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Receiver added...

ASSAN PPM out receiver
Removed all un necessary pins. And solder PPM out direcly.

Sorry for the bad picture
Here
RCG Plus Member
Old Sep 05, 2011, 02:39 AM
olivierb is offline
Find More Posts by olivierb
Registered User
Beautiful look. I know what you meant now
Very clean building.
Old Sep 05, 2011, 06:17 AM
NaterPin is offline
Find More Posts by NaterPin
Registered User
Quote:
Originally Posted by olivierb View Post
Hi everybody,

I have installed KKmulticopter kit onto this frame and it flies great.
After balancing the props, what I never done, it is night and day.
I can even hover indoor in a not so large room
Here are some pics.

Olivier.

Attachment 4256457

Attachment 4256458

I am going to use the same props and motors. Any idea of the thrust of that setup?
Old Sep 05, 2011, 07:04 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by olivierb View Post
Beautiful look. I know what you meant now
Very clean building.
tanks ... Hope it will fly as good as it look.

Searching a "Dome" out of plastic cup etc

NaterPin:
check that post, there is a Prop chart
Here
RCG Plus Member
Old Sep 05, 2011, 08:50 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Better picture of the Quadrino board with the Assan PPM receiver...

High Resolution Here

High Resolution Here
RCG Plus Member
Old Sep 05, 2011, 04:40 PM
blackmoon is online now
Find More Posts by blackmoon
flying beam
blackmoon's Avatar
Quote:
Originally Posted by Dialfonzo View Post
Receiver added...

ASSAN PPM out receiver
Removed all un necessary pins. And solder PPM out direcly.

Sorry for the bad picture
Here
which one of the assan's rx was it ?

Thank you.
Last edited by blackmoon; Sep 05, 2011 at 04:52 PM.
Old Sep 05, 2011, 06:44 PM
Puffer Ghoti is offline
Find More Posts by Puffer Ghoti
What arbre?? oh tree!
Puffer Ghoti's Avatar
Quote:
Originally Posted by blackmoon View Post
which one of the assan's rx was it ?

Thank you.
It is the one sold by HK (assan X8-R6MP) but is not correct in the picture or write-up. I received 2 recently for HK so can confirm the post below.

https://www.rcgroups.com/forums/show...postcount=5460

Item; its X8-R6MP

http://www.hobbyking.com/hobbyking/s...idproduct=9122
Old Sep 05, 2011, 08:20 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by Puffer Ghoti View Post
It is the one sold by HK (assan X8-R6MP) but is not correct in the picture or write-up. I received 2 recently for HK so can confirm the post below.

https://www.rcgroups.com/forums/show...postcount=5460

Item; its X8-R6MP

http://www.hobbyking.com/hobbyking/s...idproduct=9122
Tanks ...

BTW: i got my ASSAN receiver from Him.. LOL
RCG Plus Member
Old Sep 06, 2011, 11:35 PM
flyhigh300 is offline
Find More Posts by flyhigh300
Registered User
Dialfonzo,

Hmmm you sure all the part are in there ?? ha ha..

Super Clean job man..



Quote:
Originally Posted by Dialfonzo View Post
Receiver added...

ASSAN PPM out receiver
Removed all un necessary pins. And solder PPM out direcly.

Sorry for the bad picture
Here
Old Sep 07, 2011, 07:07 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by flyhigh300 View Post
Dialfonzo,

Hmmm you sure all the part are in there ?? ha ha..

Super Clean job man..
HiHi... !
Yes everything is there. I have scratch my head a bit to find the right way for the ESC. But i am Happy with the result..

But i would like it to actualy Fly.. lol
Need to remove vibrations.

BTW: Do you want me to build on for you .. LOL...
RCG Plus Member
Old Sep 07, 2011, 07:27 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
I have an idea for a LED ring but i don't have PCB sheet and can't cut them anyway... lol
RCG Plus Member
Old Sep 07, 2011, 02:58 PM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar
Well guys,
I have been working on my setup for a couple of days, to come to the conclusion that the Openpilot CC board wont work with the new 10amp Plush esc Man i want to get this in the air, anyone have 4 esc they would like to sell me??
Thanks Gary


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion DiaLFonZo-Copter TrinitY Quad V2.0 Dialfonzo Multirotor Talk 316 Mar 12, 2012 05:46 AM
Build Log KX-2 V1.0 Dragon kristjane Multirotor Talk 4 Oct 06, 2011 02:16 PM
Sold TacCon FS One Hangar 9 v1.0 Controller smallmax Aircraft - General - Miscellaneous (FS/W) 4 Apr 09, 2011 10:31 PM
Discussion Easy osd v1.0 or v1.2 borsel FPV Talk 2 Jul 10, 2010 05:35 AM
Idea A nifty tool for you guys/girls that program pics etc it is ASCII V1.0.0 flyman668 DIY Electronics 5 Dec 15, 2004 01:47 AM