Thread Tools
Old Jul 13, 2011, 04:41 AM
kajakmannen is offline
Find More Posts by kajakmannen
Registered User
kajakmannen's Avatar
Discussion

Altitude hold / Position hold on QuadX with Flight Ctrl clone card.


Hi

COuld anyone direct me towards information on how to connect pressure sensor and GPS to a Flight Ctrl clone card (Gold edition) 1.35.

Thanks in advance / Kajakmannen
Sign up now
to remove ads between posts
Old Jul 13, 2011, 03:52 PM
willi_m is online now
Find More Posts by willi_m
Registered User
Pressure sensor is there already
Old Jul 13, 2011, 07:45 PM
G-unit is offline
Find More Posts by G-unit
WHEN IN DOUBT FLOOR IT!!!
G-unit's Avatar
Just check the box it the TOOL, and assigned it to a channel..
Old Jul 14, 2011, 03:30 AM
kajakmannen is offline
Find More Posts by kajakmannen
Registered User
kajakmannen's Avatar
Thanks. I have done that and when I test the Quad looses altitude and even if I have engaged the altitude hold I can change the altitude with the throttle lever. What can be wrong if it behavous like this?

Thanks in advance / Kajaken
Old Jul 14, 2011, 05:23 AM
Quad_Addict is offline
Find More Posts by Quad_Addict
Suspended Account
Quote:
Originally Posted by kajakmannen View Post
Thanks. I have done that and when I test the Quad looses altitude and even if I have engaged the altitude hold I can change the altitude with the throttle lever. What can be wrong if it behavous like this?

Thanks in advance / Kajaken
we need to see a video. throttle should be in center for vario mode if not quad will beep till you find center while engaged. when activated it will beep with stick lower or higher depending if you wanna set height lower or higher.

in standard altitude hold when you flip the switch it should hold. but some things to look for when setting it up..

your altitude tab settings...
depending on your geographic elevation
stick position when your flipping switch

maybe even covering the sensor. i think i responded to you before but here is the video how i set up for vario alt hold.
-
Mikrokopter Vario Height control explained ( IN ENGLISH) (5 min 38 sec)
Old Jul 14, 2011, 05:51 AM
hawaiitaco is offline
Find More Posts by hawaiitaco
Registered User
hawaiitaco's Avatar
Quote:
Originally Posted by kajakmannen View Post
Thanks. I have done that and when I test the Quad looses altitude and even if I have engaged the altitude hold I can change the altitude with the throttle lever. What can be wrong if it behavous like this?

Thanks in advance / Kajaken
like QA stated...or you prob have to adjust mingas if you are in height hold?
Old Jul 14, 2011, 09:18 AM
kajakmannen is offline
Find More Posts by kajakmannen
Registered User
kajakmannen's Avatar
I use altitude hold (not vario) and have not done any changes from the default values. Should the min gas be increased and how much in each step till it works?

Best regards / kajaken
Old Jul 14, 2011, 10:50 AM
Quad_Addict is offline
Find More Posts by Quad_Addict
Suspended Account
Quote:
Originally Posted by kajakmannen View Post
I use altitude hold (not vario) and have not done any changes from the default values. Should the min gas be increased and how much in each step till it works?

Best regards / kajaken
in the video i posted above in the beginning i show the settings use the same one, im guessing your min gas is set to high. match it to mine in the video, i took a screen shot of the video

-


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product FY91Q with GPS Position Hold-Telemetry,Firmware and Configuration Software feiyudz Multirotor Talk 2030 Aug 09, 2015 02:33 AM
Discussion Altitude hold with the Sport SeismicCWave Hoverfly Technologies 3 Jul 11, 2011 04:53 PM
Discussion trex 600 heli position and altitude hold - how to? djdaveq UAV - Unmanned Aerial Vehicles 0 Dec 02, 2007 10:34 PM