3DHS 48" EDGE 540 (1.5 Buck Huck) - Page 599 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Jul 17, 2012, 09:49 PM
3d NOOBular
3DNater's Avatar
make sure you pre-drill. I would hate for the formers to crack
Sign up now
to remove ads between posts
Jul 17, 2012, 09:53 PM
Just wanna fly!
grovey's Avatar
Quote:
Originally Posted by brathanke
make sure you pre-drill. I would hate for the formers to crack
The smallest drill bit I have is 1/16. Is that sufficient forth screws provided?

The drill I have also cannot reach, lol, this is a mission!
Jul 17, 2012, 09:58 PM
3d NOOBular
3DNater's Avatar
well I suppose you could start your hole with a servo screw or something. A hand drill is a great hobby tool. that being said... I dont have one either
Jul 17, 2012, 09:59 PM
3d NOOBular
3DNater's Avatar
when I did mine I used a larger blind nut and a bolt. The larger drill bit was long enough to reach with my drill.
Jul 17, 2012, 10:06 PM
Just wanna fly!
grovey's Avatar
This is what I have right now.

I hope this will hold and not crack or damage the plane when I land.



Name: ImageUploadedByTapatalk1342577129.356798.jpg
Views: 90
Size: 109.6 KB
Description:
Jul 17, 2012, 10:14 PM
3d NOOBular
3DNater's Avatar
looks good to me. there will be almost zero pressure on that screw. kinda like a wing bolt... doesnt do much but hold the wing snug. the anti rotation pin and wing tube do all the heavy lifting. those formers and the wedge will be plenty strong to keep the gear in place.
Jul 17, 2012, 10:18 PM
Just wanna fly!
grovey's Avatar
Maybe after a few landings the gear will seat properly! Hehe
Jul 17, 2012, 10:20 PM
Fly Naked !
MARCOELDRAGON's Avatar
I had similar trouble with both of my orange Edges. Had to use sanding sticks that wife uses on her nails to open up the slots in order to get the wire in. Then ended up sanding the wedges to get them to fit all the way. This was not a problem with my blue Edge. I think the covering on the orange Edges for some reason shrinks a bit tighter than the blue. I had some slight warping of the bottom of several formers in the rear fuse on both orange ones but not on the blue.
Jul 17, 2012, 11:10 PM
3D-wanna-B
theK2's Avatar
Quote:
Originally Posted by brathanke
wood screw man. that gear will bend and you will be kicking yourself if you glue it.
+1 - and all you need is a small screw. Don't over-complicate it - like was said... that screw doesn't have to do much but keep the gear from falling out. There is no vertical force (down) being exerted on the gear ---- unless you really screw up.
Jul 17, 2012, 11:14 PM
Addicted to 3DHS and EF
3Daddict's Avatar
I epoxied my gear in, and if I ever have to replace it I am going to have a "FUN" time removing it with a dremal. But I think the plane will go before the gear.
Jul 17, 2012, 11:39 PM
inverted-i-fly
3drcparts's Avatar
293 flights on my original epoxied in gear, well over 400 landings and this was my first 3d plane bought back in Sept of last year, sure the gear bends, I just bend it back
Jul 18, 2012, 02:42 AM
Fly Easy
djowtlaw's Avatar
Quote:
Originally Posted by Inverted-I-Fly
293 flights on my original epoxied in gear, well over 400 landings and this was my first 3d plane bought back in Sept of last year, sure the gear bends, I just bend it back
First thing that comes to mind is fatigue! Although I bet there will (hopefully) be a few thousand cycles of bending before any cracks show.
Jul 18, 2012, 02:45 AM
3d NOOBular
3DNater's Avatar
My re-pod edge still has straight gear... against all odds I've probably flown it about 50 times.
Jul 18, 2012, 03:23 AM
I fly, therefore, I crash!!!
SteveT.'s Avatar
Hey guys.....

Since I bought myself a lathe, I have been trying to figure out a few things to make to make a few bucks with it. So...for those that would like some of the aluminum "buttons" that I designed for the landing gear mod, I am going to make those... Let me know if you're interested....
Latest blog entry: My hangar...
Jul 18, 2012, 04:04 AM
TEAM HILLBILLY
Eagle34's Avatar
Quote:
Originally Posted by SteveT.
Hey guys.....

Since I bought myself a lathe, I have been trying to figure out a few things to make to make a few bucks with it. So...for those that would like some of the aluminum "buttons" that I designed for the landing gear mod, I am going to make those... Let me know if you're interested....
Those are great Steve, I had Cmala make me a set when he first started machining things. Work great.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product 3DHS 41" Edge "$99 Buck Huck" Ducati Mechanic 3D Flying 17299 Mar 27, 2012 04:37 PM
Sold 3dhs 41' edge buck huck bnf JBuck Aircraft - Electric - Airplanes (FS/W) 7 Jul 02, 2011 07:58 AM
Sold 3DHS 41" EDGE - ORANGE - 99 Buck Huck 6L6Amp Aircraft - Electric - Airplanes (FS/W) 14 Aug 22, 2010 08:45 PM