Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Nov 30, 2012, 06:00 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
Got more parts in.... all the way from Australia...
Sign up now
to remove ads between posts
Old Dec 01, 2012, 11:21 AM
Capt.Crash is offline
Find More Posts by Capt.Crash
**NOT GUILTY**
Capt.Crash's Avatar

Some new crew members showed up...


...this should also make the winch handles less likely to get broke the next time I drop my cell phone...
Old Dec 01, 2012, 06:29 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
Damn, there is 8 of them..... I only have 7... :-(
Last edited by BrushlesHeaven; Dec 01, 2012 at 06:41 PM.
Old Dec 01, 2012, 06:43 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
Got my Yamaha mast upgraded with still wire in silicone coating...
Hmmm, should be fine I think...
Old Dec 01, 2012, 08:55 PM
Capt.Crash is offline
Find More Posts by Capt.Crash
**NOT GUILTY**
Capt.Crash's Avatar
Quote:
Originally Posted by BrushlesHeaven View Post
Damn, there is 8 of them..... I only have 7... :-(
Another half dozen fellows want to try out...but I don't think I have much more room on deck...
Old Dec 01, 2012, 08:56 PM
Capt.Crash is offline
Find More Posts by Capt.Crash
**NOT GUILTY**
Capt.Crash's Avatar
Quote:
Originally Posted by BrushlesHeaven View Post
Got my Yamaha mast upgraded with still wire in silicone coating...
Hmmm, should be fine I think...
Those look like they will be plenty strong..
Old Dec 02, 2012, 11:03 AM
Boomer1 is online now
Find More Posts by Boomer1
Boomer1
Boomer1's Avatar
I noticed that none of Crash's crew is touching any part of another crew member's anatomy. I was hoping that was not contagious!

Kidding aside, the deck looks great - lots of great detail. Love it!

Robert - you rigging looks great and should yield a much stronger set up. Remember not to over tighten the rigging screws. With the new set up it is tempting to torque those screws down.

Looking forward to seeing the finished set up!

Boomer
Old Dec 02, 2012, 05:27 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
They are well made and strong but too big for me. Should do better research before I order them... :-(
I will not use them. Will see maybe Doby will get them off me for $100.00 ...
He's got the size of boat they are good for...
I got the new set on the way...
Plus I need to make sure my mast is easy in and out for transportation reasons...
Will have to be able to transport Yamaha and other 5 FE boats at the same time and I have small car...








Quote:
Originally Posted by Boomer1 View Post
I noticed that none of Crash's crew is touching any part of another crew member's anatomy. I was hoping that was not contagious!

Kidding aside, the deck looks great - lots of great detail. Love it!

Robert - you rigging looks great and should yield a much stronger set up. Remember not to over tighten the rigging screws. With the new set up it is tempting to torque those screws down.

Looking forward to seeing the finished set up!

Boomer
Last edited by BrushlesHeaven; Dec 02, 2012 at 05:32 PM.
Old Dec 02, 2012, 06:09 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
Mast support installed and dry.
Spinnaker boom installed.
My riser tube for the main was ripped off the deck last time on the water so I had to design new one.
This time I will use fairly strong plastic bolt with washer and screw installed from top.
Drilled small hole inside... Hope this will stay stronger this time.
Plexy glass plate on the bottom to get better support...
Old Dec 02, 2012, 07:09 PM
Capt.Crash is offline
Find More Posts by Capt.Crash
**NOT GUILTY**
Capt.Crash's Avatar
That should be strong enough to hold an elephant...

Murphy (a club member) was over today drooling on my boat and is looking for a Yamaha or Seawind ...so if anyone knows where to get one?

He is very unhappy with the Vela...even after all the mods....here is another pic of us from last weekend.
Old Dec 02, 2012, 10:19 PM
Boomer1 is online now
Find More Posts by Boomer1
Boomer1
Boomer1's Avatar
Quote:
Originally Posted by BrushlesHeaven View Post
Got more parts in.... all the way from Australia...

Robert
I don't believe I have seen those particular rigging screws before. I use the sailsetc 30-030. I have some of the 30-035 but they they were a bit to large in diameter for the Yamaha (for me) could be alright for some one else - just sayin...........

Some time ago I picked up some Pekabe 482 - must say they are really good looking -

What size are the rigging screws you got from Australia?

Boomer
Old Dec 02, 2012, 11:15 PM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
That is what I just got from them, 30-030 few and 30-035 maybe for the future boat...
The once from Australia are very well made but too large to be installed 2 on stock mounting on the hull....
I like them a lot, only if they are the right size...
Pekabe 482 are looking funtastic and I like the fact they have quick on off on them.
I am sure 30-030 will work well for me. The objective is quick set up out of the car and back...
Here is some pictures...
Last edited by BrushlesHeaven; Dec 02, 2012 at 11:28 PM.
Old Dec 03, 2012, 03:17 PM
lhurt is offline
Find More Posts by lhurt
Registered User
Are those fittings the Sails Etc Compression Struts? Will they resist a load in tension?
Old Dec 04, 2012, 12:42 AM
BrushlesHeaven is offline
Find More Posts by BrushlesHeaven
Lipo Power
BrushlesHeaven's Avatar
Yes, I have them from

http://radiosailingshop.com.au

product code 26-090

At this moment I do not need them, they are for sale...



Quote:
Originally Posted by lhurt View Post
Are those fittings the Sails Etc Compression Struts? Will they resist a load in tension?
Last edited by BrushlesHeaven; Dec 04, 2012 at 09:25 AM.
Old Dec 04, 2012, 11:51 AM
Boomer1 is online now
Find More Posts by Boomer1
Boomer1
Boomer1's Avatar
Robert
If you haven't posted them on the forums classified section it might be a place to move those items into the hands of someone that can use them
Just a thought

I discovered this online store that has some nice looking hardware.Worth a look for future needs.
http://stores.ebay.com/LongBeachRC/_...1&_sop=1&_vc=1
Boomer
Last edited by Boomer1; Dec 05, 2012 at 09:06 AM.


Thread Tools