Thread Tools
Old Oct 19, 2011, 03:17 PM
nft343 is offline
Find More Posts by nft343
Registered User
I THINK that's for a RX which can pass the PPM stream directly out, not as separate channels.

Quote:
Originally Posted by Bear_Pants View Post
I have a question regarding this

"5- Make sure to remove the propeller from the motor at this stage. Connect GPS and all inputs to RVOSD:
RVOSD defaults to "regular" inputs. This means each channel of the receiver has to be connected to separate input channels on RVOSD. If you want to use a PPM ready receiver you can use the “PPM configuration” explanation, else configure inputs and outputs like this:"

Now. I'm not sure I understand. I do have a dragon link that is run off PPM. I'm just not sure I follow what this part means. I have everything hooked up like normal (lots of wires). Not sure what the PPM configuration is for.
Sign up now
to remove ads between posts
Old Oct 19, 2011, 03:26 PM
ScooterInVegas is offline
Find More Posts by ScooterInVegas
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by lrrps View Post
On the Range Video site, I found this: RVOSD5 main Main_5.05S Release date: 23/July/2011

Did I miss something?

I didn't find the 5.06 thingy.
Right below the 5.05 is the 5.06 thingy....
Old Oct 19, 2011, 03:28 PM
Firatp is offline
Find More Posts by Firatp
Registered User
Firatp's Avatar
Quote:
Originally Posted by ScooterInVegas View Post
Yep. 5.06 was released this month.
Thanks I found them.
Is there a sequence between main and video board when updating ?
Thanks
Old Oct 19, 2011, 03:29 PM
Bear_Pants is offline
Find More Posts by Bear_Pants
Suspended Account
Quote:
Originally Posted by nft343 View Post
I THINK that's for a RX which can pass the PPM stream directly out, not as separate channels.
Hm. Not sure. Would be cool to lessen up the wires
Old Oct 19, 2011, 03:31 PM
ScooterInVegas is offline
Find More Posts by ScooterInVegas
Village Idiot!
ScooterInVegas's Avatar
Yes the DL has PPM on ch 9 I think. If you have the new Rx, its the top and bottom pins, not the middle.
Old Oct 19, 2011, 03:34 PM
Bear_Pants is offline
Find More Posts by Bear_Pants
Suspended Account
Quote:
Originally Posted by ScooterInVegas View Post
Yes the DL has PPM on ch 9 I think. If you have the new Rx, its the top and bottom pins, not the middle.
Okay. I'm going to double check that picture posted in the thread.

So this means I don't need all those servo wires everywhere? Just one wire from channel 9 into my ppm1 on RVOSD?

I'd also need to hook up a wire for the RSSI as well to right?

Bah I'm confused now.

Channel 9 is not marked but It's stated that it's a PPM channel

There is a separate PPM channel for a servo wire to plug into. However I'm not positive on what is the correct way. This is a new receiver.
Last edited by Bear_Pants; Oct 19, 2011 at 03:39 PM.
Old Oct 19, 2011, 03:39 PM
ScooterInVegas is offline
Find More Posts by ScooterInVegas
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Bear_Pants View Post
Okay. I'm going to double check that picture posted in the thread.

So this means I don't need all those servo wires everywhere? Just one wire from channel 9 into my ppm1 on RVOSD?

I'd also need to hook up a wire for the RSSI as well to right?
Yep
Old Oct 19, 2011, 03:50 PM
Bear_Pants is offline
Find More Posts by Bear_Pants
Suspended Account
Quote:
Originally Posted by ScooterInVegas View Post
Yep
Cool it works! Going to carefully hook up the RSSI... can I do it with the servo wire that came with my rvosd?
Old Oct 19, 2011, 03:52 PM
ScooterInVegas is offline
Find More Posts by ScooterInVegas
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Bear_Pants View Post
Cool it works! Going to carefully hook up the RSSI... can I do it with the servo wire that came with my rvosd?
I dont know.........can ya?

Yes
Old Oct 19, 2011, 03:54 PM
man2000me is offline
Find More Posts by man2000me
Mums the word.
man2000me's Avatar
Yes, 1 (3 servo wire) for ppm, 1 (1 wire) for rssi, and 1 (3 servo wire) for current sensor. The you servos and thorttle connect to the rvosd.
Last edited by man2000me; Oct 20, 2011 at 11:08 AM.
Old Oct 19, 2011, 04:01 PM
Firatp is offline
Find More Posts by Firatp
Registered User
Firatp's Avatar
My question to whom succeeded flash RVOSD

I made the connection and selected device family but it says "No device detected. Ensure proper capacitance on VDDCORE/VCAP pin. "
Do I need to some setting additional?
Thanks
Old Oct 19, 2011, 04:16 PM
Elcheapo is offline
Find More Posts by Elcheapo
Registered User
Elcheapo's Avatar
Quote:
Originally Posted by Bear_Pants View Post
Cool it works! Going to carefully hook up the RSSI... can I do it with the servo wire that came with my rvosd?
Read the RSSI configuration part of this instructions: http://rangevideo.com/forum/showthre...progress...%29
Old Oct 19, 2011, 04:17 PM
Elcheapo is offline
Find More Posts by Elcheapo
Registered User
Elcheapo's Avatar
Quote:
Originally Posted by Firatp View Post
My question to whom succeeded flash RVOSD

I made the connection and selected device family but it says "No device detected. Ensure proper capacitance on VDDCORE/VCAP pin. "
Do I need to some setting additional?
Thanks
Make some side pressure by setting some inclination on the pickit so it makes better contact with the board.
Old Oct 19, 2011, 04:20 PM
SpookiePower is offline
Find More Posts by SpookiePower
Registered User
Quote:
Originally Posted by Firatp View Post
My question to whom succeeded flash RVOSD

I made the connection and selected device family but it says "No device detected. Ensure proper capacitance on VDDCORE/VCAP pin. "
Do I need to some setting additional?
Thanks
I did also have problems getting it to connect. But after many attempts, it finally worked out.
Old Oct 19, 2011, 04:31 PM
Bear_Pants is offline
Find More Posts by Bear_Pants
Suspended Account
Figured it out. Should be set to fly. When it doesn't rain :\


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Maiden Reports 12345 Arizona Model Aviators 744 Oct 16, 2015 10:17 PM
Help! RVOSD thermal sensors rcmonster99 FPV Talk 16 Jun 20, 2011 11:21 AM
Discussion Weekend weather reports neck Arizona Model Aviators 13 Jun 10, 2011 05:59 PM
Discussion where are the Joe Nall horror "reports? guy hanson Radios 49 May 18, 2011 01:06 PM
Discussion Finally Fixed the Country Reports daboz Dynamic Soaring 5 May 16, 2011 03:51 AM