RVOSD - V5 - reports - Page 60 - RC Groups
Thread Tools
Oct 19, 2011, 02:08 AM
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Firatp
Hi again,
How can I learn my RVOSD's firmware version?
Thanks
When you start the OSD, it will show the firmware # for the first couple of sec.
Sign up now
to remove ads between posts
Oct 19, 2011, 02:17 AM
Suspended Account
Quote:
Originally Posted by ScooterInVegas
When you start the OSD, it will show the firmware # for the first couple of sec.
Video 5.03 Sensor 5.06

Am I up to date?
Oct 19, 2011, 02:52 AM
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Bear_Pants
Video 5.03 Sensor 5.06

Am I up to date?
Yep. 5.06 was released this month.
Oct 19, 2011, 02:54 AM
Suspended Account
Quote:
Originally Posted by ScooterInVegas
Yep. 5.06 was released this month.
Okay. So yeah with my prop on the vibrations are horrible. It's pretty chipped up prop though. I have the OSD wrapped in foam and velcrod not too tightly. Vibrations all the way up. I guess I'll just see how she does in the air.
Oct 19, 2011, 04:09 AM
Registered User
Firatp's Avatar
Quote:
Originally Posted by ScooterInVegas
Yep. 5.06 was released this month.
Hello,
It is not shown in Rangevideo.com. Where is it published?
thanks
Oct 19, 2011, 04:12 AM
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Firatp
Hello,
It is not shown in Rangevideo.com. Where is it published?
thanks
Its over at ........ Rangevideo.com. In the "Latest Firmare Version" thread,

http://rangevideo.com/forum/showthre...n-for-your-OSD
Oct 19, 2011, 11:12 AM
Registered User
Quote:
Originally Posted by ScooterInVegas
On mine, its from the Tx/camera battery. But hooked up to one battery would give you your pack voltage and you can set the mAh warning setting to compensate for only reading one pack.

Wait, I forgot about Amp Load. I dont know it each pack will "see" the whole amp load or not. Voltage yes, amp load, I dont know.
Are there any other options for current sensors that can handle the higher voltage and current? would the eagletree elogger v4 work with rvosd.
Oct 19, 2011, 12:56 PM
Registered User
Or does range video offer a stronger current sensor?
Oct 19, 2011, 01:01 PM
Village Idiot!
ScooterInVegas's Avatar
Don't think so. 99% of users dont use that many amps. Have you signed up on their forum? They are in there more of the time to answer questions.
Oct 19, 2011, 01:09 PM
Suspended Account
Quote:
Originally Posted by ScooterInVegas
Don't think so. 99% of users dont use that many amps. Have you signed up on their forum? They are in there more of the time to answer questions.
scooooooooooottteeeeeeeeeeeeeerrrrrrrrrrrrrrrrrrrr rrrr
Oct 19, 2011, 01:15 PM
Village Idiot!
ScooterInVegas's Avatar
Quote:
Originally Posted by Bear_Pants
scooooooooooottteeeeeeeeeeeeeerrrrrrrrrrrrrrrrrrrr rrrr
Pants be of bear?
Oct 19, 2011, 01:17 PM
Suspended Account
Quote:
Originally Posted by ScooterInVegas
Pants be of bear?
WEEEEEEEEEEEEEEEEEEEEEE

just got my dragonlink.

It's raining like a b*tch though.
Oct 19, 2011, 02:37 PM
Registered User
Quote:
Originally Posted by ScooterInVegas
Don't think so. 99% of users dont use that many amps. Have you signed up on their forum? They are in there more of the time to answer questions.
I'm asking about it on their forum:

http://rangevideo.com/forum/showthre...ring-questions

I haven't got an answer yet regarding current sensor options. Are there any other OSDs out there that include an IMU autopilot that can do more than just RTH? (heading hold, position loiter, waypoints, etc...) I might just have to go with eagle tree because I know their elogger current sensor is rated for something like 100 amps and 80 volts. Although I don't think they have the awesome autopilot stuff that RVOSD V5 has...
Oct 19, 2011, 02:48 PM
Registered User
lrrps's Avatar
Quote:
Originally Posted by ScooterInVegas
When you start the OSD, it will show the firmware # for the first couple of sec.
On the Range Video site, I found this: RVOSD5 main Main_5.05S Release date: 23/July/2011

Did I miss something?

I didn't find the 5.06 thingy.
Oct 19, 2011, 02:56 PM
Suspended Account
I have a question regarding this

"5- Make sure to remove the propeller from the motor at this stage. Connect GPS and all inputs to RVOSD:
RVOSD defaults to "regular" inputs. This means each channel of the receiver has to be connected to separate input channels on RVOSD. If you want to use a PPM ready receiver you can use the “PPM configuration” explanation, else configure inputs and outputs like this:"

Now. I'm not sure I understand. I do have a dragon link that is run off PPM. I'm just not sure I follow what this part means. I have everything hooked up like normal (lots of wires). Not sure what the PPM configuration is for.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Maiden Reports 12345 Arizona Model Aviators 744 Oct 16, 2015 10:17 PM
Help! RVOSD thermal sensors rcmonster99 FPV Talk 16 Jun 20, 2011 11:21 AM
Discussion Weekend weather reports neck Arizona Model Aviators 13 Jun 10, 2011 05:59 PM
Discussion where are the Joe Nall horror "reports? guy hanson Radios 49 May 18, 2011 01:06 PM
Discussion Finally Fixed the Country Reports daboz Dynamic Soaring 5 May 16, 2011 03:51 AM