



Quote:








You can access all the menus with the IR remote control, but only the inflight menus with the RC Tx. Those menus control the settings that you could want to tweak while flying.
If the PPM string fails(cable gets disconnected) RVOSD will set RTH or switch to the second PPM input(second receiver) if the second PPM input is enabled. This is a feature already. 





Quote:
What do you think about the winds aloft idea? No other OSD has this, it would really stand out from the competition, and its a simple E6B calculation once you have the raw data coming in. 


Last edited by iskess; Sep 01, 2012 at 04:39 AM.





FBW Problem
Posted on another thread but this one seems a lot more active...
Testing FBW on the ground. The elevator goes down when I point the nose down and up when I point the nose up. This is just the opposite of what should happen to stabilize the plane. Control surfaces are working correctly when transmitter sticks are used. Any ideas? The RVOSD is pointing forward and I have run thru all the steps in the manual more than once. Thanks, 





Quote:
Quote:
2There is an step on the wizard that ask you to set the elevator for maximum climb, do it properly. 


















ezuhf
Are any of you using your RVOSD 5 with a EZUHF? I see a place in the instructions that talk about setting up RSSI using the EZUHF rx's. The instructions talk about PWM RSSI signal from EZUHF.
What is PWM RSSI signal?? When I use the combined PPM mode I can't seem to get my fail safe set right so i'm using "regular" rx setting at the moment with "glitch counter". Can someone help me out with the terminology and rx settings. I"m using my EZUHF with a 9cap. thanks for any help, Todd 





Quote:
Alex, thank you for being so open to suggestions. It is very exciting to be part of the evolution. 






Quote:







Wind Velocity and Direction FormulaQuote:
Here are the formulas: The math behind the equation requires the use of vectors and triangle geometry. You are required to break each vector down into its vertical and horizontal component. Subtract the GS vector from the TAS vector for each vertical and horizontal value and the wind speed is calculated using pythagoream theorem A^2 + B^2 = C^2 where C is the wind speed. The wind direction is calculated using the arctan function and checking if the wind is a headwind of a tailwind WS = Wind Speed WD = Wind Direction TC = True Course TH = True Heading TAS = True Airspeed GS = Groundspeed Here is the formula for the wind speed (you can use this in Excel provided you use Named Ranges) WS =ROUND(SQRT(((SIN(RADIANS(MOD(TH, 360)))*TAS)(SIN(RADIANS(MOD(TC, 360)))*GS))^2 +((COS(RADIANS(MOD(TH, 360)))*TAS)(COS(RADIANS(MOD(TC, 360)))*GS))^2), 0) Breaking down the formula, we are using pythagoream theorem WS = square root([Horizontal Value Difference]^2 + [Vertical Value Difference]^2) and rouding the number to the nearest whole number Here is the formula for the wind direction WD =ROUND(MOD(DEGREES(ATAN(((SIN(RADIANS(MOD(TH, 360)))*TAS)(SIN(RADIANS(MOD(TC, 360)))*GS))/((COS(RADIANS(MOD(TH, 360)))*TAS)(COS(RADIANS(MOD(TC, 360)))*GS))))+IF(((COS(RADIANS(MOD(TH, 360)))*TAS)(COS(RADIANS(MOD(TC, 360)))*GS))<0, 180, 0), 360), 0) Breaking down this formula, we are getting the arctangent([Horizontal Value Difference] / [Vertical Value Difference]) and then checking the sign of the [Vertical Value Difference] and adding 180 if it is negative. To simplify the calculations into manageable chunks, open up excel and copy these into a cell. When you copy the formula change the name of the cell to what it equals or change to the appropriate cell (A1) GSH = SIN(RADIANS(MOD(TC, 360)))*GS ‘Horizontal Portion of GS Vector GSV = COS(RADIANS(MOD(TC, 360)))*GS ‘Vertical Portion of GS Vector TASH = SIN(RADIANS(MOD(TH, 360)))*TAS ‘Horizontal Portion of TAS Vector TASV = COS(RADIANS(MOD(TH, 360)))*TAS ‘Vertical Portion of TAS Vector DeltaH = TASHGSH ‘Horizontal Vector Difference DeltaV = TASVGSV ‘Vertical Vector Difference WS = ROUND(SQRT(DeltaH^2 +DeltaV^2), 0) ‘Pythagoream Theorem rounded WD = ROUND(MOD(DEGREES(ATAN(DeltaH/DeltaV))+IF(DeltaV<0, 180, 0), 360), 0) ‘arc tangent plus check for Vertical Vector Difference sign 






Quote:
Of course, I can also google searching for this stuff, but my point is, that it is not enough to copy the formula from the first link you get. It takes a lot more than this. There is no simplicity at all on this process. This is why I have to make a balance between the usefulness of new features and the time it takes to implement, then choose what to do next. 


Last edited by Elcheapo; Sep 01, 2012 at 05:54 PM.





Quote:
At least keep it on the wish list. Maybe every so often you can post a poll to rank new requests and see what people want. I know everyone has different priorities. I think this would be awesome. 



Thread Tools  
Similar Threads  
Category  Thread  Thread Starter  Forum  Replies  Last Post 
Discussion  Maiden Reports  12345  Arizona Model Aviators  744  Oct 16, 2015 09:17 PM 
Help!  RVOSD thermal sensors  rcmonster99  FPV Talk  16  Jun 20, 2011 10:21 AM 
Discussion  Weekend weather reports  neck  Arizona Model Aviators  13  Jun 10, 2011 04:59 PM 
Discussion  where are the Joe Nall horror "reports?  guy hanson  Radios  49  May 18, 2011 12:06 PM 
Discussion  Finally Fixed the Country Reports  daboz  Dynamic Soaring  5  May 16, 2011 02:51 AM 