



Hi Guillaume
It's just : (coeff / kv˛) / weight(kg)˛ = motor armature resistance Ri A 80% efficiency motor should have the coeff around 300, 75% efficiency > 550/600. I see rpm = kv * (U  ( Ri+a.rpm.I ) ) and Pout = ( rpm/kv ) * ( I  Io[rpm] ) What is a ? The "dyno" one is another model, very accurate, where: rpm = kv[I/U] * ( URi.IL[rpm] ) and Pout = ( I*rpm/kv )  Po[rpm] What is L[rpm] ? Curious the term (I*rpm/kv) and not V*I Louis 






Hi
Here is a link to dc motor math model formulas. But only in German available. http://www.powercroco.de/ModellierungTheorie2.doc Best regards Micha 





Louis,
Seems like I was tired when I wrote the formula! I should have wrote (Ri+a.rpm).I instead of (Ri+a.rpm.I) : rpm = kv * (U  ( Ri+a.rpm).I ) and Pout = ( rpm/kv ) * ( I  Io[rpm] ) But! a.rpm.I in this model is the voltage drop due to inductance... which I've called L in the other model (stupidly because of confusion with inductance L !). L[rpm] just means that, in this model, L is function of rpm... I've wrote rpm/kv because it's shorter than URi.IL[rpm], this is what is sometime called back EMF I guess, and written UR.I. I know it isn't all exact and very "science looking", but easy to use and accurate enough to have a good idea of the torque when the prop is near the peak efficiency domain (at this point, small measurement errors can have big effects on the calculated efficiency). BTW, interesting things on this paper (2.3.3 Why Control is Necessary: Motor Inductance): http://web.mit.edu/scolton/www/SCThG.pdf and the author's blog: http://scolton.blogspot.com/ You may know it already? Micha, thanks for sharing this file! I think that any good drive model can use props data from wind tunnel tests as long as it shows well the main effects. Propcalc is not based on props tests but on airfoils tests and props geometry but in fact it goes in the same direction. I don't understand why there is no software using those data with an electric motor model. Is there any? 





Hi yomgui
Quote:
model in flight is very hard. You must solv iterative a lot of equations. My father has written a program in tcl/tk with a matlab interface. But due to the complexity of system, sometimes the results are imaginary, not solvable. My father has used propeller formulas from http://www.mhaerotools.de. But anyway, it is an interesting scope. We are flying mostly powered gliders, so it is very important to have an efficient drive chain, adapted to the glider. Our goal is to achieve a good (max) altitude with a given battery energy. Best regards Micha 






Quote:
There is a difference if you consider a) Overall formulas in steady state at the ESC input (Vbatt, I averaged, rpm..) given a hardware ESC b) or "transitory states" inside one "electrical cycle" and six steps sub cycle when you are designing a PMBLDC controler In case b) inductance is important to consider (with the term L di/dt) In case a) L is of no importance and the "classical formulas" : rpm = Kv * (V  Rm I) Kv = rpmo / (V  Rm Io) @ no load are quite valid but Rm is a function of copper temperature Louis 






Hi Louis
You're probably right ! In fact I must admit that i'm not at all an expert of brushless. My formulas are mostly based on imaginary values, the game's being to find the model that gives the best estimated value for torque. I can compare torque measured on a dyno (homemade, but i believe it's quite accurate) with votls, amps, rpm and motor temperature. But I can't measure torque inside the wind tunnel's test room. So I need a model of my motor that can convert volts, amps and rpm at given temp into mechanical power and torque, etc... The two models i've mentionned... i can't really explain them (that's a shame !), unless that they are better for my purpose then the "classical model", because they allow a better repeatability of Cp measurement with different motors, they also "explain" my recordings in a better way. And they have the advantage to show quite the same results while they are in fact very different. So I guess both are close to truth. 

Last edited by yomgui; Aug 20, 2011 at 04:14 PM.
Reason: poor english, sorry!

Thread Tools  
Similar Threads  
Category  Thread  Thread Starter  Forum  Replies  Last Post 
Wind Tunnel Smoke  zagisrule!  Power Systems  23  Feb 06, 2015 01:28 AM  
MiniReview  Turbo Ace 915 V2 9g Motor with Pictures, Video, Flight Tests, and Thrust Tests  Tom Z  Micro Helis  96  Aug 12, 2011 08:48 PM 
Question  Wind Tunnel for kiteboarding tests?  DougE  Sailplane Talk  1  Jan 16, 2008 04:42 PM 
Discussion  Wind Tunnel Tests  Aphorism's Dream  Ornithopters  0  Apr 30, 2007 12:36 PM 
sources of wind tunnel pics  Tim Green  Modeling Science  0  Feb 10, 2003 08:29 PM 