Thread Tools
Aug 19, 2012, 08:13 AM
I have a video for that
its for safety
Sign up now
to remove ads between posts
Aug 19, 2012, 08:32 AM
Registered User
jimbob69's Avatar
just gave my new GPS unit on my stealth quad a test run in the back garden, Position hold works pretty damn well (wind is light today, 5mph), even though i have yet to cover the baro hole,
not really enough room to fully test the RTH function but upon engaging in yawed and headed back to launch position(i disengaged pretty quick, garden is no that big), REALLY impressed with how easy to setup and implement this unit is, and the for the cost!!
i did drop the alt PID to 1.2 as suggested by crazyj,
good stuff!!
Aug 20, 2012, 09:33 AM
Registered User
Good evening. Need help how to translate the gyroscope in reverse, on the model of Scarab Avatar FPV G10 - ARF electronica - twin servo Tricopter
Aug 20, 2012, 03:32 PM
Registered User
Hello all... a quick question... may be slightly "off thread" as it's not particular to the airframe itself, but I've read EVERY post in this thread as I've planned my first purchase from MultiWi and come to appreciate the collective experience.
I just received my AOI goggles for FPV and didn't think about 12V power. I'm flying my quad with 4S, so I can't just use a spare.
What capacity and rating (mA and "C" rating) are you all using for driving goggles or your receivers (ie: 305). I believe I'd read that I don't need much more than a 20C which would keep cost down, but I'm curious about capacity vs cost... re: C ratings.
If you could share with me what you all may be using, it would be GREAT...

Thanks in advance
Aug 20, 2012, 03:50 PM
SILURIA / UK
Shikra's Avatar
Quote:
Originally Posted by vova75
Good evening. Need help how to translate the gyroscope in reverse, on the model of Scarab Avatar FPV G10 - ARF electronica - twin servo Tricopter
Which gyro board? Sirius? pitch/roll or yaw incorrect?
Aug 20, 2012, 03:55 PM
SILURIA / UK
Shikra's Avatar
I bought a dirt cheap 4000mah 15c from ebay 2 years ago and run my entire GS off that - lcd screen / trackers, dual rx, recorder, video multiplier. Also pan/tilt servos.

rc305 rx will run of 12v, don't know about the goggles.

Virtually any C rating greater than 1 will do you!


Quote:
Originally Posted by 10x200
Hello all... a quick question... may be slightly "off thread" as it's not particular to the airframe itself, but I've read EVERY post in this thread as I've planned my first purchase from MultiWi and come to appreciate the collective experience.
I just received my AOI goggles for FPV and didn't think about 12V power. I'm flying my quad with 4S, so I can't just use a spare.
What capacity and rating (mA and "C" rating) are you all using for driving goggles or your receivers (ie: 305). I believe I'd read that I don't need much more than a 20C which would keep cost down, but I'm curious about capacity vs cost... re: C ratings.
If you could share with me what you all may be using, it would be GREAT...

Thanks in advance
Aug 20, 2012, 05:35 PM
Registered User
Hi I'm new. I have here a http://www.multiwiicopter.com/produc...lectronica-fpv. I'm new and I can not understand why spinning like a top to the left then to the right on the ground and I can not lift it. Really need your help.
Aug 20, 2012, 05:39 PM
I have a video for that
Quote:
Originally Posted by vova75
Hi I'm new. I have here a http://www.multiwiicopter.com/produc...lectronica-fpv. I'm new and I can not understand why spinning like a top to the left then to the right on the ground and I can not lift it. Really need your help.
Did you order the Paris board with Tricopter MINUS software ?

All the Scarab Tri airframes need reverse yaw set in the sketch file (firmware)
Aug 20, 2012, 05:44 PM
Registered User
Quote:
Originally Posted by Deet_aus
Did you order the Paris board with Tricopter MINUS software ?

All the Scarab Tri airframes need reverse yaw set in the sketch file (firmware)
No, I do not know! If you tell me how I will be grateful to you
Aug 20, 2012, 06:18 PM
MultiCopterPilot & Film Maker
crazyj's Avatar
Quote:
Originally Posted by vova75
Good evening. Need help how to translate the gyroscope in reverse, on the model of Scarab Avatar FPV G10 - ARF electronica - twin servo Tricopter
I think you have the Trikopter/Avatar - correct? The issue sounds like the YAW direction needs to be reversed in the firmware/code - just like Deet said.

Look for the code section under Conf.H in the MultiWii ardunio code and choose the reverse rotation for the tricopter yaw. Then upload the modified code to the ardunio. :-)


/************************************************** ***********************************************/
/**************** SECTION 2 - COPTER TYPE SPECIFIC OPTIONS *******/
/************************************************** ***********************************************/

/******************************** TRI *********************************/
//#define YAW_DIRECTION 1
#define YAW_DIRECTION -1 // if you want to reverse the yaw correction direction
/* you can change the tricopter servo travel here */
#define TRI_YAW_CONSTRAINT_MIN 1100
#define TRI_YAW_CONSTRAINT_MAX 1900
#define TRI_YAW_MIDDLE 1500 // tail servo center pos. - use this for initial trim; later trim midpoint via LCD
Aug 21, 2012, 02:42 AM
Registered User
What to put on the menu board arduino-1.0.1, this model Scarab Avatar FPV G10 - ARF electronica - twin servo Tricopter
Aug 21, 2012, 02:49 AM
Registered User
Quote:
Originally Posted by crazyj
I think you have the Trikopter/Avatar - correct? The issue sounds like the YAW direction needs to be reversed in the firmware/code - just like Deet said.

Look for the code section under Conf.H in the MultiWii ardunio code and choose the reverse rotation for the tricopter yaw. Then upload the modified code to the ardunio. :-)


/************************************************** ***********************************************/
/**************** SECTION 2 - COPTER TYPE SPECIFIC OPTIONS *******/
/************************************************** ********************************************

/******************************** TRI *********************************/
//#define YAW_DIRECTION 1
#define YAW_DIRECTION -1 // if you want to reverse the yaw correction direction
/* you can change the tricopter servo travel here */
#define TRI_YAW_CONSTRAINT_MIN 1100
#define TRI_YAW_CONSTRAINT_MAX 1900
#define TRI_YAW_MIDDLE 1500 // tail servo center pos. - use this for initial trim; later trim midpoint via LCD
What to put on the menu board arduino-1.0.1, this model Scarab Avatar FPV G10 - ARF electronica - twin servo Tricopter
Aug 21, 2012, 11:43 AM
Registered User
jimbob69's Avatar
testing my scarabs position hold in a reasonable breeze, 12-14 mph and gusty, switched PH off at around 42secs, apologies for my poor video compressions skills and shakes.

http://www.youtube.com/watch?v=207qtilTr8Q
Aug 21, 2012, 03:09 PM
Registered User
Quote:
Originally Posted by crazyj
The new Carbon Scarab Avatar is done, flight tested and ready to go for tomorrow's FPV adventure! It took only a couple of nights to build, but many months for me to find the time and motivation.
Whoa. That's one fine looking machine. 4 months or so to Christmas, right? Pretty sure I've been a good boy this year.
Aug 21, 2012, 09:43 PM
Registered User

Avatar Maiden


Finally got time to fly this evening. 4 packs back to back so far and getting things dialed in. I'm probably going to fly Los for a while and then install the fpv gear I bought with the kit.

Super impressed with this platform. Kit went right together and flew very nicely right out of the box. This will be my 8th fpv model and I must say this has been the smoothest build so far!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Twisted Hobbys - Telink 43" SU 29 - Build, Fly, Vid hercdriver7777 3D Foamies 634 Nov 16, 2014 09:06 PM
Discussion Radical RC Stick 400 Build Thread~~~Now with Video Carnifax Electric Plane Talk 186 Aug 20, 2014 08:55 PM
Question Skywalker 3 Build Advice and Eventual Build Thread! Ecibob FPV Talk 2 May 01, 2011 04:46 PM
Discussion Easyglider Build Thread (Help wanted) worzul Foamies (Kits) 2 Mar 18, 2011 07:45 AM