Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old May 21, 2012, 04:22 PM
pavcon is offline
Find More Posts by pavcon
Suspended Account
at the cost of those fans you can get a Lander EDf unit..
no reason to pay so much money just touse a motor thatyou have layign around
Sign up now
to remove ads between posts
Old May 21, 2012, 05:52 PM
The Don is offline
Find More Posts by The Don
Park Pilot Mag. Jets Columnist
HET 6404 accepts 28mm motor and comes with 3mm and 3.17mm collet. I have them in stock (USA located)

http://donsrc.com/cart/index.php?_a=...product_id=120
Old May 21, 2012, 06:20 PM
pavcon is offline
Find More Posts by pavcon
Suspended Account
Quote:
Originally Posted by The Don View Post
HET 6404 accepts 28mm motor and comes with 3mm and 3.17mm collet. I have them in stock (USA located)

http://donsrc.com/cart/index.php?_a=...product_id=120
if Dons Says so.. its good
I didn't know that.. that's good.. though In the 64 category that's my oly plane and I think it will remain my only plane..
Old May 21, 2012, 07:49 PM
vanderbrander is offline
Find More Posts by vanderbrander
Just an Earth bound misfit - I
vanderbrander's Avatar
Quote:
Originally Posted by pavcon View Post
at the cost of those fans you can get a Lander EDf unit..
no reason to pay so much money just touse a motor thatyou have layign around
Didn't say they were cheap Pav

But if you want the hottest Stinger on the block- one of these and a HET 1W30 will probably get you there. You'd want a really good 4S 2200 battery though

Don's option of a HET 64 is more to my liking.
Old May 21, 2012, 11:11 PM
miketre is offline
Find More Posts by miketre
Mike
miketre's Avatar
anyone else tried the space shuttle launch with or without success?
If so, please share your setup.

I'll try mine this weekend if the weather is good. I doubt I'll be successful, considering the strength of the throw i need to give for a successful hand launch.
Old May 22, 2012, 07:50 AM
NCRealEstateGuy is offline
Find More Posts by NCRealEstateGuy
I Used To Have More Free Time!
Miketre... when I tried to stand my Stinger on its exaust cone, I found that the horizontal stabilizers extend about one inch past the tail cone. It is impossible for mine to sit on its tail cone. How did the one in the video do it?
Old May 22, 2012, 05:19 PM
Alpha10 is offline
Find More Posts by Alpha10
Registered User
Alpha10's Avatar
I just ordered a RC Lander 64mm 3900kv Red Velocity setup for the Stinger.

I figured with a 60amp HW ESC I can start with it on 3s with a mild bump in performance over stock and always have the room for even more on 4s!

I can't wait!
Last edited by Alpha10; May 22, 2012 at 05:34 PM.
Old May 24, 2012, 08:28 AM
miketre is offline
Find More Posts by miketre
Mike
miketre's Avatar
Quote:
Originally Posted by NCRealEstateGuy View Post
Miketre... when I tried to stand my Stinger on its exaust cone, I found that the horizontal stabilizers extend about one inch past the tail cone. It is impossible for mine to sit on its tail cone. How did the one in the video do it?
Well, I tried it just now and was also unable to make it rest straight up.
Old May 24, 2012, 08:50 AM
Evan D is offline
Find More Posts by Evan D
Registered User
Evan D's Avatar
Can I suggest that you drill holes through the plastic skids on the bottom front and rear so you can put a rod through them like we did for model rockets. That will enable it to stand vertical and also keep it tracking straight for the critical first couple feet.
Old May 24, 2012, 08:57 AM
networker is offline
Find More Posts by networker
Today is a good day to fly.
networker's Avatar
Quote:
Originally Posted by miketre View Post
Well, I tried it just now and was also unable to make it rest straight up.
c'mon guys. you're modelers...cobble a launch pad out of foam, rocks, paperbacks, tupperware—whatever's in your back seat at the moment.
Old May 25, 2012, 04:02 PM
Ben D Wing is offline
Find More Posts by Ben D Wing
Registered User
Ben D Wing's Avatar
Quote:
Originally Posted by miketre View Post
Well, I tried it just now and was also unable to make it rest straight up.
No probs in the grass (see pic), but it does lean slightly on a hard surface.
Old Jun 05, 2012, 04:16 PM
Alpha10 is offline
Find More Posts by Alpha10
Registered User
Alpha10's Avatar
I'm pumped to get my Stinger in the air this weekend. Just curious as to what you guys are running as far as D/R and Expo on your surfaces.

I have triple rates so I was thinking:

Ailerons: 60, 70, 80% with +20, 30, 40 Expo
Elevator: 65, 75, 85% with +5 ,10, 15 Expo
Rudder: 65, 75, 85% with +5, 10, 15 Expo

IDK how sensative the elevators or rudder is?

I'd appreciate any suggestions. Thanks!
Last edited by Alpha10; Jun 05, 2012 at 04:49 PM.
Old Jun 05, 2012, 04:33 PM
pavcon is offline
Find More Posts by pavcon
Suspended Account
Ive flown the stinger once more yesterday. it had been inactive for quite sometime..
I wasgoing to try the nasa launch but it was too windy and it was pushhing the plane down to it's LG
next time
Old Jun 05, 2012, 07:41 PM
Draven is offline
Find More Posts by Draven
Fly Low Fly Fast
Draven's Avatar
Would this power setup be any better than the stock setup?

I have this EDF combo laying around from an old project so I don't know if it's worth the effort to swap it out.
http://www.hobbyking.com/hobbyking/s...W_4300kv_.html
Old Jun 05, 2012, 08:46 PM
Draven is offline
Find More Posts by Draven
Fly Low Fly Fast
Draven's Avatar
I decided against it. Not worth it IMO. So I improved the ventilation.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product New HobbyKing Viper Jet 70mm Fibreglass Jet Jagzilla Electric Ducted Fan Jet Talk 1591 Sep 05, 2016 07:48 PM
Discussion Stinger F3B/F3F Vaclavs new weapon! SpeedMaster Multi Task F3X 124 Aug 08, 2013 10:00 PM
For Sale Nib sr71 64 mm ducted fan jet yf22raptor Aircraft - Electric - Jets (FS/W) 6 Mar 26, 2011 03:28 PM
Discussion HobbyKing EDF 64 Identification liam2317 Electric Ducted Fan Jet Talk 11 Dec 20, 2009 08:52 AM