Thread Tools
Old May 13, 2011, 01:12 PM
cactus is offline
Find More Posts by cactus
Registered User
Nice photo, I see what you mean. Basically you have one of the ESC's + and - leads going into the Rx then ONE (like throttle) of your Rx to FC is a complete three pin connection, everything else is only a signal pin.
Sign up now
to remove ads between posts
Old May 13, 2011, 01:21 PM
witespy is offline
Find More Posts by witespy
Registered User
you got it.

picture of rx side.

I use any open port to power the rx. Aux1 for the batt port is free for binding. ( you can bind with USB POWER ONLY , which is nice )




Last edited by witespy; May 13, 2011 at 01:30 PM.
Old May 13, 2011, 02:45 PM
Dolby is offline
Find More Posts by Dolby
Needs more bacon!
Dolby's Avatar
If I wanted to use this board for a Y6 would I just add pins here? Or is it not possible...

What motors would connect in what order?

(and of course modify the multiwii config and re-upload to the board)
Last edited by Dolby; May 13, 2011 at 02:53 PM.
Old May 13, 2011, 02:58 PM
cactus is offline
Find More Posts by cactus
Registered User
Quote:
Originally Posted by Dolby View Post
If I wanted to use this board for a Y6 would I just add pins here? Or is it not possible...

What motors would connect in what order?

(and of course modify the multiwii config and re-upload to the board)
I think you have to use PPM sum (an rx that can do this) down the throttle connection from the rx to the Quadrino. Then you have code changes and stuff to do. I'm not sure how the six Esc's would connect.....
Old May 13, 2011, 07:46 PM
SeismicCWave is offline
Find More Posts by SeismicCWave
AMA 46133
Paul,

Can the board handle a Y4 configuration?
Old May 13, 2011, 08:31 PM
RTRyder is offline
Find More Posts by RTRyder
Registered Lunatic
RTRyder's Avatar
My Quadrino arrived late this afternoon, first chance I got I swapped out the KK blue board on the VC-20 430mm Gaui frame, hooked the board up to the computer to verify settings, then out in the backyard to try it out.

Seems to have a severe case of the wobbles, if this were a KK or Gaui controller I'd just lower the gain setting(s) till it calmed down and go fly. Not so quick and easy apparently with the MultiWii variants, time for some PID tuning. I made a few small changes before it got dark and not in the right direction, looks like this is going to take a lot of trial and error to get it right.

Can anyone give a quick rundown of which settings are the right ones to change to tame wobble and in which direction?
Old May 13, 2011, 09:56 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
RTRyder , Wanna sell your KK board?
Old May 13, 2011, 10:11 PM
witespy is offline
Find More Posts by witespy
Registered User
Increase value for P until oscillations start, then back of slightly.



on a VIC450 frame 3.2 is a good number to start with .
lower the autolevel strength too
Old May 13, 2011, 10:32 PM
NaterPin is offline
Find More Posts by NaterPin
Registered User
you have a pm Paul
Old May 13, 2011, 10:38 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Here is the video of my witespy quad with the new quadrino in stalled

S8302553 (5 min 49 sec)
Old May 13, 2011, 11:20 PM
Laddy McMurry is offline
Find More Posts by Laddy McMurry
Registered User
Laddy McMurry's Avatar
Come on Dad, let me fly!!!
Old May 13, 2011, 11:25 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Last year she flew my slow stick. she did pretty good. I think I will wait a few years before I let her fly the quad
Old May 14, 2011, 12:16 AM
RTRyder is offline
Find More Posts by RTRyder
Registered Lunatic
RTRyder's Avatar
Quote:
Originally Posted by tc3wins View Post
RTRyder , Wanna sell your KK board?
The blue board, heck no, its going back in the quad I took it off of to get this frame setup for the Quadrino!

I have a previous generation red board from Minsoo Kim I might part with though...
Old May 14, 2011, 12:20 AM
RTRyder is offline
Find More Posts by RTRyder
Registered Lunatic
RTRyder's Avatar
Quote:
Originally Posted by witespy View Post
Increase value for P until oscillations start, then back of slightly.



on a VIC450 frame 3.2 is a good number to start with .
lower the autolevel strength too
Thanks. It's allready oscillating so I'll start by lowering P and see where that goes, should have a lot more time to play around with it later today...
Old May 14, 2011, 12:25 AM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
RTRyder, PM sent.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Article Hangar 9's Piper J-3 Cub 40 Plug-N-Play PNP Plug N Play Evo 46NT Powered ARF Review tailskid2 Scale Fuel Planes 13 Oct 09, 2016 05:15 PM
Help! need new flight controller recommendations n3m1s1s Multirotor Talk 115 Jan 09, 2012 10:38 AM
Article Subsonic's Motrolfly Plug and Play Power System: Motor, Controller & Battery Review Michael Heer Power Systems 27 Dec 16, 2010 01:36 PM
Data Plug 'n Play separates: An Esky CP2 with an E-flight 2 in 1... elan Micro Helis 3 Mar 19, 2010 09:51 AM
Discussion Air Hogs Plug n'Play Flight Deck Simulator trust416 Micro Ready-to-Fly 14 Aug 05, 2007 11:44 AM