Thread Tools
Old May 02, 2011, 03:17 PM
Capt.Crash is offline
Find More Posts by Capt.Crash
**NOT GUILTY**
Capt.Crash's Avatar
That boat is looking sweet!
Sign up now
to remove ads between posts
Old May 02, 2011, 06:41 PM
Ed Crowell is online now
Find More Posts by Ed Crowell
Registered User
Ed Crowell's Avatar
Nice looking hull, I like the modification of the bow and stern.

Ed
Old May 02, 2011, 08:56 PM
Schrott is offline
Find More Posts by Schrott
Kraut
thanks guys,

We take a lot of things for granted, juniper makes good fence poles and a very nice smelling firewood.
Junipers in our area a old, very old, a 12 to 18 inch juniper is probably a couple of hundred years old.
I have no idea if those extraordinary colours in the wood are a result of the soil and growing conditions, dry and altitude.

I found out that the natural bleaching of unprotected juniper will change the colouring to a more brownish tone, the overal rose will stay.

A nother wood that I think is very interesting is Rushian Olive, it goes from white to blakish brown. This tsuff was introduced to the west in the 1900.
It grows like a weed were ever there is water. I have to do a black ops in the reservation and cut down one of those suckers.
Last edited by Schrott; May 02, 2011 at 09:04 PM.
Old May 02, 2011, 09:28 PM
Dick L. is offline
Find More Posts by Dick L.
Registered User
Dick L.'s Avatar
Ha ! Now I am more determined than ever to "help" the neighbor drop his tree ! Thanks for the visuals. Instead of boat planks, I see some other sort of fine arts woodworking in the tree's future.
Old May 03, 2011, 10:53 PM
Schrott is offline
Find More Posts by Schrott
Kraut

Operation Schneewitchensarg


With all the stuff I put on that tub, she aint going to fit into my car any more fully rigged. I like to get to the lake and just dump it into the water.
So now I had to find a way to haul her around, in the future.
My biggest concern was the balast inside the hull, if unsurported it would, could or what ever, do some damage to the ABS hull.
Since I had some ply lying around I built the schneewitchensarg. The idea, wrap the hull in foam set it in the box and than use high expansion foam out of the can to fill out the left over space.
If that works I should have a nicely fitting form to suport the hull threw all the pumps of the road and I can put the whole catastrophy in an enclosure on a little trailer.
By tomorrow afternoon I should know, if I screwd up or if I got a nice transportation box.
Old May 04, 2011, 10:53 AM
Dick L. is offline
Find More Posts by Dick L.
Registered User
Dick L.'s Avatar
Be very careful with the foam - if it expands it could "crush" the hull. Do a little at a time and maybe fill the hull with water to counter the expanding foam.
Old May 04, 2011, 12:59 PM
Schrott is offline
Find More Posts by Schrott
Kraut
Thanks for the advice.
I finished to foaming this morning and as of jet the hull is still in one piece.
Old May 06, 2011, 10:13 AM
Schrott is offline
Find More Posts by Schrott
Kraut
so yesterday I got my best kitchen knife out and trimmed everything that was not needed of and lifted the hull out of the form.
It worked very nice and when I put the hull back in I had a very nice tight fit.
Since the foam is not uv resitened, I will have to put a lid on it, 1/4 ply should do it
I found in my junk yard some old trailer pieces, front part of an inline horse trailer, should make a nice base for a boat hauling trailer.
Old May 07, 2011, 10:40 PM
Schrott is offline
Find More Posts by Schrott
Kraut
I finished the rough out of the schneewitchensarg.
As usual things don't go the way as you have planed, especialy if it is the first

But overal I am pleased with the result and I think it will do the trick.
Old May 10, 2011, 04:06 PM
Schrott is offline
Find More Posts by Schrott
Kraut
Today I did some cooking, on the menue was a sweet lead stew called balast.
I had from the tire guys around 30 pounds of lead, which I melted down and poured into the form.
I always like that part, lots of fun.

The result turned out to be pretty nice, I just have to smooth it out and cut a few slices out of so I can change the destribution of the weight in order to balance the tub.
Old May 11, 2011, 09:50 AM
Schrott is offline
Find More Posts by Schrott
Kraut
After sanding and taking some ruff spots of the balast I attached a handle and than checked how it fits.
Old May 12, 2011, 12:17 AM
MILLERTIME is offline
Find More Posts by MILLERTIME
Taking care of the pond.
MILLERTIME's Avatar
Very interesting.
Old May 12, 2011, 11:35 AM
Schrott is offline
Find More Posts by Schrott
Kraut
Now it gets kinde interesting, I have to find masts, I can get the original robbe masts, but lets say with freight it gets a little expensive.
I would like to stay with alumium masts, the Atlantis masts are 54 inches tall, ovall shaped with a groove to slide the sails in.
Were can I get something like that.
Old May 12, 2011, 12:10 PM
martin richards is offline
Find More Posts by martin richards
Useful Idiot
Quote:
Originally Posted by Schrott View Post
Now it gets kinde interesting, I have to find masts, I can get the original robbe masts, but lets say with freight it gets a little expensive.
I would like to stay with alumium masts, the Atlantis masts are 54 inches tall, ovall shaped with a groove to slide the sails in.
Were can I get something like that.
http://www.ludwigrcyachts.com/spars.htm
Old May 12, 2011, 05:39 PM
Schrott is offline
Find More Posts by Schrott
Kraut
Thanks Martin
very useful

That is 1/2 the price of Robbe masts.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale World Models Vodoo P51 Mustang bolarobric Aircraft - Electric - Airplanes (FS/W) 7 Nov 23, 2007 05:29 AM
Discussion The Top 6 Signs Your Child's Teacher Is Experiencing Burnout Don Sims Humor 0 May 27, 2003 05:50 PM
Strobe Lights from Child's Rubber Ball? Ray Manhart Parkflyers 3 Aug 22, 2002 08:46 PM