Shop our Airplanes Products Drone Products Sales
Apr 20, 2012, 02:12 PM
Registered User
Quote:
Originally Posted by SnowDog1974 View Post
It's whatever works for you; the engine doesn't care. I flipped my carb over so I could mount the throttle servo to the bottom of the engine box.
do you have to drill a hole behind the carb?
Sign up now
to remove ads between posts
Apr 20, 2012, 02:58 PM
Registered User
Quote:
Originally Posted by VENOMiTry View Post
do you have to drill a hole behind the carb?
I would...just go to Ace and get a simple 1" hole saw that you can stick in a drill
Apr 20, 2012, 04:08 PM
3d NOOBular
3DNater's Avatar
Tom, tell me about battery placement for ignition and servos. Are they pretty far forward or closer to the wing tube? Just curious. I'm running a life for ignition and a lipo for servos. Both unregulated so there isn't any extra crap in there for power share or voltage regulators.
Apr 20, 2012, 05:31 PM
Wannabe 3D Pilot
flyracer's Avatar
even with my batteries right behind the wing tube my Slick is a little nose heavy.. I'm running only one elevator servo and I'm seriously considering doing two to try and get the CG more neutral
Apr 20, 2012, 07:45 PM
Registered User
I am just getting ready to start building mine. This will be my 3rd slick. I was curious for the guys running the DLE30 with a cannister which cannister are you using?
Apr 20, 2012, 09:15 PM
Registered User
Quote:
Originally Posted by brathanke View Post
Tom, tell me about battery placement for ignition and servos. Are they pretty far forward or closer to the wing tube? Just curious. I'm running a life for ignition and a lipo for servos. Both unregulated so there isn't any extra crap in there for power share or voltage regulators.
Hey Nate, my battery is back under the hatch latch.......i had to install an additional tray to do that. My CG is a tiny bit nose heavy in this configuration where i like it. I tried it up by the wing tube but it was too nose heavy. Unless you do 2 elevator servos, you can probably plan on doing the same thing
Apr 20, 2012, 09:42 PM
3d NOOBular
3DNater's Avatar
ok great info guys. thanks.
Apr 21, 2012, 08:35 AM
Wannabe 3D Pilot
flyracer's Avatar
CRFan
I think I might go with adding a tray to reposition my batteries.... post a pic of yours in you can please

Flyracer
Apr 21, 2012, 03:33 PM
Registered User
Quote:
Originally Posted by flyracer View Post
CRFan
I think I might go with adding a tray to reposition my batteries.... post a pic of yours in you can please

Flyracer
I just cut a piece of light ply and epoxied it in between the former under the latch and the area where the pull pull servo goes. Simple as that really
Apr 22, 2012, 10:38 AM
Registered User
i ordered this one.

http://www.sdshobby.net/muffler-cani...ine-p-654.html
Apr 22, 2012, 10:56 AM
Registered User
if you guy's are taking pictures of you building the plane
could you please post them?
it would be nice to see every ones setup.
and the equipment you are using.
thank you.
Apr 22, 2012, 07:25 PM
Registered User
FLYING-HIGH thanks for the link. I take it they are out of china. How long did it take to get yours?


Just ordered my servos,prop, and engine. Should have this built by next weekend.
Last edited by Cmircman; Apr 22, 2012 at 08:42 PM.
Apr 22, 2012, 09:07 PM
3d NOOBular
3DNater's Avatar
Quote:
Originally Posted by FLYING-HIGH View Post
if you guy's are taking pictures of you building the plane
could you please post them?
it would be nice to see every ones setup.
and the equipment you are using.
thank you.
You may have already seen these since I'm pretty sure they have been posted on this thread before (can't remember for sure). But here are pics of my build so far. It has been sitting for a little over a week with no progress due to waiting on parts. the last part should arrive tomorrow so it may be all finished up this week. Additional pics will be posted to this same album as more progress is made.

You can see the mods applied to the motorbox. This is due to how the first version of the 70" slick was made to accomodate a side-carb DLE 30. We cut out 25mm to make room in the cowl for the PTE 36cc that occupies the same exact space as a DLE 30.

We ended up wishing we would have cut out 30mm but it is going to be great how it is. Incidentally the newer version has a MB that is 30mm shorter than the original.

http://imageshack.us/g/818/img0445nl.jpg/
Apr 22, 2012, 10:02 PM
Wannabe 3D Pilot
flyracer's Avatar
Mr Slick in der Slick
Apr 22, 2012, 10:05 PM
3d NOOBular
3DNater's Avatar
Quote:
Originally Posted by flyracer View Post
Mr Slick in der Slick
Sweet details


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion 71" AJ Slick Gas - First time with gas Hewey19 Fuel Plane Talk 7 Sep 06, 2011 03:53 PM
Sold 3dhs 71" aj slick - nib 6L6Amp Aircraft - Electric - Airplanes (FS/W) 4 Apr 05, 2011 11:09 AM
Discussion I'm torn, 71 slick or 72 sc? KillerCut 3D Flying 9 Mar 25, 2011 06:20 PM
Discussion 3DHS 42"Slick Side Force Generators bigtexas 3D Flying 3 Mar 03, 2011 12:42 PM
Wanted 3DHS 70" Slick Gas parts!!! helifryer Aircraft - Fuel - Airplanes (FS/W) 0 Feb 20, 2011 07:47 AM