Thread Tools
Mar 25, 2012, 11:00 AM
Registered User
Ok, what platforms are your current sensors good for ?
mwc only ?
Sign up now
to remove ads between posts
Mar 25, 2012, 11:14 AM
Suspended Account
The one where you pay him and then get ignored.
Mar 25, 2012, 12:29 PM
Registered User
Well, tell me other source for a well priced IMU with MS5611 please?
Mar 27, 2012, 08:16 AM
Registered User
Quote:
Originally Posted by timecop View Post
The one where you pay him and then get ignored.
All people which write me PM or email receive answer.
Mar 27, 2012, 08:23 AM
Registered User
Quote:
Originally Posted by RENATOA View Post
Ok, what platforms are your current sensors good for ?
mwc only ?
You can use any platform what support MS5611 and other sensors. MultiWii or MegaPirate code.
Mar 27, 2012, 08:24 AM
Suspended Account
Quote:
Originally Posted by RENATOA View Post
Well, tell me other source for a well priced IMU with MS5611 please?
Assuming any code to actually make (proper) use of the sensor exists.
Mar 27, 2012, 09:24 AM
Aleksey Kharlanov
Quote:
Originally Posted by CSG_EU View Post
You can use any platform what support MS5611 and other sensors. MultiWii or MegaPirate code.
MegaPirateNG supports only FreeIMU 0.4.1 (0.4.3) with MS5611. AllInOne supported in theory since we work with this sensor. But nobody reports that it works actually.
Mar 27, 2012, 09:51 AM
Registered User
Isn't an IMU the sum of the sensors on the board ? It's a retorical question because we know this is true.
Then why do you induce the feeling that an imu could embed some kind of intelligence than could make it behave better than the other ?
I can happily buy freeimu if not priced in Euro, same amount as allinone in usd, both manufacturers being from EU...
Mar 27, 2012, 09:56 AM
Suspended Account
A "real" IMU would contain a processor that computes attitude based on all sensor data. All these "IMUs" that are peddled by various ebay/viacopter/etc sellers are nothing more than breakout boards for a bunch of sensor chips. And severely overpriced, at that. A proper IMU is also temperature/etc calibrated, with sensor axises properly aligned, etc etc.
Mar 29, 2012, 02:44 AM
Registered User
Can anybody send me a complete configured multiwii-sketch for an "11DOF IMU Board 5V HMC5883L BMA180 MS5611 ITG3200 NEO-6Q GPS" ?
My ACC->Z and MAG->YAW doesnt work correctly.
I've tested with and without soldered clock-jumper...

Can anybody help me ?
Mar 29, 2012, 02:53 AM
Registered User
Solder clock jumper to GND!
solder also address jumper!
Mar 29, 2012, 05:52 AM
Registered User
My board doesnt have an address-jumper. look at the picture...

My configuration:
#if defined(ALLINONE)
#define ITG3200
#define BMA180
#define MS561101BA
#define HMC5883
#define ACC_ORIENTATION(X, Y, Z) {accADC[ROLL] = -X; accADC[PITCH] = -Y; accADC[YAW] = Z;}
#define GYRO_ORIENTATION(X, Y, Z) {gyroADC[ROLL] = Y; gyroADC[PITCH] = -X; gyroADC[YAW] = -Z;}
#define MAG_ORIENTATION(X, Y, Z) {magADC[ROLL] = X; magADC[PITCH] = Y; magADC[YAW] = -Z;}
#define ITG3200_ADDRESS 0XD0
#define BMA180_ADDRESS 0x82
#define MS561101BA_ADDRESS 0xEC
#endif
Last edited by Nightwalker84; Mar 29, 2012 at 06:09 AM.
Mar 29, 2012, 07:48 AM
Trying to learn.
leprud's Avatar
Any chances to get MPU6050 10DOF schematic?
Apr 01, 2012, 05:04 AM
Registered User
Quote:
Originally Posted by leprud View Post
Any chances to get MPU6050 10DOF schematic?
PM sent
Apr 02, 2012, 03:19 PM
Registered User
Canīt anybody help me ??
CSG you are the manufacturer...you canīt help me, too ?!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold Two NIB CMOS Board Cameras 420 TVL 3.6mm lens (Only one left!) bah7566 FPV Equipment (FS/W) 0 Feb 10, 2011 05:49 AM
For Sale: PHA 01 All in one board skeppley Aircraft - Electric - Helis (FS/W) 3 Sep 10, 2004 10:33 AM
I need an all in one board for a feda dragonfly zoom boy Micro Helis 11 Aug 13, 2004 12:56 PM
Feda All-in-one board problem Chris07 Micro Helis 2 Nov 23, 2003 10:35 AM
Feda all in one board repairs Yukonho Micro Helis 7 Oct 08, 2003 06:22 PM