Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Dec 30, 2011, 04:49 PM
Wilkas is offline
Find More Posts by Wilkas
Registered User

All-in-one with GPS. Is it correct?


Some time ago I bought controller ALLINONE II with GPS: http://www.ebay.com/itm/HMC5883L-BMA...item3cba059182
Now I found time to test it. Connect it to Arduino Mega, load software MultiWiiConf_dev_20111220. All seems to work more or less normal. I only have couple of questions: counter Debug2 is counting errors. Not many, but after 5 min. of working there are 500 -1000 errors.
And second question: while controller lies on the table (GPS antenna outside), distance from home is increasing - after 5 min. of work - more than 50 meters.
Is it normal? What I should check?
There is short video how it looks:
All-in-one with GPS test (1 min 24 sec)


Errors appearing when GPS enabled in software and GPS RX ir connected to Arduino RX2 (pin 17). When GPS disabled and nothing connected to pin17 no errors.
Last edited by Wilkas; Dec 31, 2011 at 03:02 AM.
Sign up now
to remove ads between posts
Old Jan 02, 2012, 04:43 PM
chaosdestro0 is offline
Find More Posts by chaosdestro0
Quad lover.
chaosdestro0's Avatar
If I want to get the sensor board to use with paris v4, where would VDD on the sensor board go to? In paris v3 it goes to D12, would it go to the one labelled pin 12 for paris v4?
Old Jan 09, 2012, 06:43 PM
Flyingflow is offline
Find More Posts by Flyingflow
has built nothing yet
Flyingflow's Avatar

Another Allinone Acc problem


Hi all,

I purchased the Allinone board with HMC5883L, ITG3200, BMA180 BMP085 a year ago. Now that I finally get to try it, I get no response from the accelerometer, the rest is fine.
There has been talk about setting the I2C-address, but I can't find that in the current code (20111220). The sample code posted by csg_eu some posts ago gives a compiler error.
Any ideas, anyone?

By the way, I have soldered the jumpers.

Regards,

Flow
Last edited by Flyingflow; Jan 09, 2012 at 07:23 PM.
Old Jan 10, 2012, 03:14 AM
Flyingflow is offline
Find More Posts by Flyingflow
has built nothing yet
Flyingflow's Avatar

Another Allinone Acc problem


Hi again,

I found it: In def.h in the if-clause
#if defined(ALLINONE)
i added:
#define BMA180_ADDRESS 0x82

Now everything is fine!
Last edited by Flyingflow; Jan 11, 2012 at 04:25 PM.
Old Jan 31, 2012, 07:37 AM
cestb is offline
Find More Posts by cestb
Registered User
Hi, i have the same problem with accls. Allinone works perfectly with Megapirate code but accls didn't work with multiwii (gyro, baro and compass seem ok).
I've tried to define bma address without success.
Should i solder something more than with MP code ?
Old Jan 31, 2012, 03:28 PM
cestb is offline
Find More Posts by cestb
Registered User
Its ok now, i've modified the if !#defined bma180_address
Old Mar 07, 2012, 03:26 PM
ted33 is offline
Find More Posts by ted33
Registered User
ted33's Avatar
Quote:
Originally Posted by CSG_EU View Post
You need this pin
+5V
GND
SDA
SCL
GPS rx
GPS tx
Hi
i have received my allinone II board
I'm research the pinout
thanks
Last edited by ted33; Mar 09, 2012 at 06:15 AM.
Old Mar 08, 2012, 06:30 AM
CSG_EU is offline
Find More Posts by CSG_EU
Registered User
Quote:
Originally Posted by ted33 View Post
Hi
i have received my allinone II board
I'm research the pinout
is it possible completed picture ?

thanks
Did you have 3.3 or 5V logic version?
Old Mar 08, 2012, 06:44 AM
ted33 is offline
Find More Posts by ted33
Registered User
ted33's Avatar
hi,
this version is 5v
Thanks
Old Mar 08, 2012, 03:16 PM
CSG_EU is offline
Find More Posts by CSG_EU
Registered User
Quote:
Originally Posted by ted33 View Post
hi,
this version is 5v
Thanks
Please write me PM with your email
Old Mar 12, 2012, 12:06 PM
Nightwalker84 is offline
Find More Posts by Nightwalker84
Registered User
Can anybody tell me the gps i2c-adress from the All in ONE II MS ?
Old Mar 12, 2012, 02:21 PM
CSG_EU is offline
Find More Posts by CSG_EU
Registered User
Quote:
Originally Posted by Nightwalker84 View Post
Can anybody tell me the gps i2c-adress from the All in ONE II MS ?
What sensors?
Old Mar 12, 2012, 05:14 PM
Nightwalker84 is offline
Find More Posts by Nightwalker84
Registered User
its an u-blox neo-6Q
Old Mar 23, 2012, 01:44 PM
renatoa is offline
Find More Posts by renatoa
Registered User
CSG_EU, please, can you list all your IMUs sold on your site and for each the software supporting it ?
Or, more exactly, which of your IMU works with ArduCopter 2.5 ?
You are replying very slow on eBay, or via your site Contact page, maybe here I get a faster reply. Because I want to buy !
Old Mar 25, 2012, 10:42 AM
CSG_EU is offline
Find More Posts by CSG_EU
Registered User
ArduCopter have other sensors and you need make code porting.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold Two NIB CMOS Board Cameras 420 TVL 3.6mm lens (Only one left!) bah7566 FPV Equipment (FS/W) 0 Feb 10, 2011 05:49 AM
For Sale: PHA 01 All in one board skeppley Aircraft - Electric - Helis (FS/W) 3 Sep 10, 2004 10:33 AM
I need an all in one board for a feda dragonfly zoom boy Micro Helis 11 Aug 13, 2004 12:56 PM
Feda All-in-one board problem Chris07 Micro Helis 2 Nov 23, 2003 10:35 AM
Feda all in one board repairs Yukonho Micro Helis 7 Oct 08, 2003 06:22 PM