"Swallow" mahogany runabout - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Mar 16, 2011, 11:50 AM
Registered User
szmyk's Avatar
Build Log

"Swallow" mahogany runabout


Hello.
I was "playing" with DelftShip some time ago, trying to make some project to build. As I love the mahogany classic runabouts I was heading to make something pretty .
This is what I've made up..

Swallow mahogany:

Now I'm working in AI to make drawings for laser cutting service.
Just curious, what do you think about the shape..?
Last edited by szmyk; Mar 31, 2011 at 08:51 AM.
Sign up now
to remove ads between posts
Mar 16, 2011, 11:12 PM
Registered User
Topsides look great, but not sure if its an optical illusion or not, the side on the bottom looks like it bellies down a bit. almost like a type of rocker in it. I think that this could make it bounce when running at speed
Mar 17, 2011, 07:07 PM
Registered User
I have to agree with MKC Syd, that there is way more rocker in the bottom planning surface for the hull to run right. If you put a straight edge against the bottom of the hull at the transom and go forward until the bottom of the hull no longer is against the straight edge you will see that the planning angle of attack will have the bow running far to high.

Also MKC Syd is correct in that the hull built as shown in your drawings will be very prone to hopping or bobbing up and down along with the very real problem of cavatation. I think you would be better off if you ran your bottom planning surface parallel to the base line or water line from its deepest point of transition from lifting to planning surface.
Mar 18, 2011, 06:26 AM
Registered User
szmyk's Avatar
Hello.
Thanks for the advise. You have right..I will correct it in Delft and then i will post the newer version.
In the mean time I've designed logo and letters.
Last edited by szmyk; Mar 18, 2011 at 06:52 AM.
Mar 18, 2011, 03:16 PM
Registered User
szmyk's Avatar
Ok. I've modified the project..made the bottom lines more smooth..
I think it's better than before..

Swallow:
Mar 18, 2011, 04:24 PM
Registered User
I think Don Aronow would have put his name on this one!
Mar 18, 2011, 05:32 PM
Registered User
szmyk's Avatar
Ok..I've changed the project a bit more and now I have more curvy transition from deck to the side.I think it's far better now.


And 3D view:


Now I think I can start serious drawing in AI for laser cutting.
Best Regards
Mar 19, 2011, 08:17 AM
Registered User
BY JOVE!!! I THINK HE HAS GOT IT!!! Really looking good now. The boat design looks a lot like something that would come from the boat shop of VAN DAM. I will be looking forward to the hull layout and build.
Mar 19, 2011, 10:47 AM
Registered User
szmyk's Avatar
I've made first lines plan for model.It will be 1200mm long, 240mm wide and 113mm deep hull.

I'm going back to work..
Mar 19, 2011, 05:52 PM
Registered User
Szmyk,
Very cool looking. When you say AI - mean Adobe Illustrator? ...yes?

Never thought to use the 3D tranform, if that's what your using. What version are you running if so.
Thanks, ken
Mar 19, 2011, 06:17 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by kenludd
Szmyk,
Very cool looking. When you say AI - mean Adobe Illustrator? ...yes?

Never thought to use the 3D tranform, if that's what your using. What version are you running if so.
Thanks, ken
Hi. I'm glad that you like it.
To design the shape of the hull I'm using DelftShip software,
this software provides 3D modelling.
To make drawings for Laser cut service, add strips to the project and make it strictly for modelling, I'm using Adobe Illustrator.
I don't have such experience in AutoCAD as in AI.
Mar 19, 2011, 09:24 PM
Registered User
What scale are you thinking of building in?
Mar 20, 2011, 10:33 AM
prima
Mar 21, 2011, 10:57 AM
Registered User
Congratulations!

Its hull is very beautiful. Ha some time ago I made a somewhat similar boat to that his.

Mota
Mar 22, 2011, 06:21 PM
Registered User
szmyk's Avatar

Frames almost ready


I've done some parts for laser cut, Now will try to arrange the hull inside.
Working...working..
Mar 22, 2011, 07:19 PM
Registered User
Thanks for sharing this beauty. Every time I look at it I think twin Lamborghinis.
Last edited by Nederlander; Mar 22, 2011 at 07:20 PM. Reason: typo error
Mar 23, 2011, 08:18 AM
Registered User
20 stations? I would recommend 5to 8
Mar 23, 2011, 08:36 AM
Registered User
szmyk's Avatar
Quote:
Originally Posted by finn
20 stations? I would recommend 5to 8
Hello finn..yes there are 20 stations..
If someone will build the model later, he will have always option to make less than 20.
What I'm building is the prototype of this boat..
Last edited by szmyk; Mar 26, 2011 at 03:39 AM.
Mar 23, 2011, 03:56 PM
Registered User
szmyk's Avatar
Just a few hours of thinking and planning and I'll have ready drawings for laser cutting.
In the mean time I've made sort of like side view of the boat.
I've changed the stern a little bit
Last edited by szmyk; Mar 26, 2011 at 03:39 AM.
Mar 28, 2011, 01:37 PM
Registered User
szmyk's Avatar

The parts arrived:)


Hello.
I've just collect the parts from laser cutting. NICE!







I've got to start this week.
Mar 28, 2011, 03:23 PM
"day ain't over yet-"
der kapitan's Avatar
Very neat and tidy work. must be great to have the tools to do it that nicely---.
Mar 28, 2011, 04:28 PM
Registered User
szmyk's Avatar

Deck


The very first drawings of the deck..yet without chocks and smaller parts.

Last edited by szmyk; Mar 28, 2011 at 05:10 PM. Reason: changed for colour version
Mar 28, 2011, 05:07 PM
Retired for now
I think that boat will look really nice Szmyk. Is it ready for sea trials yet? No? Well get to work. Pete
Mar 29, 2011, 10:44 AM
Registered User
szmyk's Avatar
Aye, aye, sir!
Mar 29, 2011, 11:10 AM
Retired for now
Quote:
Originally Posted by szmyk
Aye, aye, sir!
Mar 29, 2011, 05:51 PM
Registered User
szmyk's Avatar

Frames setting


Hello.
I bought the mounting board and set the frames today.
place some stringers to check if everything is on place and in right order.
So far so good...
Couple of pictures from my dockyard:











In the mean time I'm trying to find some metal laser cutting service to make the exhaust covers.
Tomorrow I will sand the formers to the shape of the hull..

Mariusz
Last edited by szmyk; Mar 29, 2011 at 06:15 PM. Reason: add plans for next day:)
Mar 29, 2011, 06:00 PM
Registered User
Very nice!!!

Mar 29, 2011, 08:28 PM
Registered User
cookiemonsta's Avatar
oh wow... oh wow.... love that shape...
Mar 29, 2011, 11:39 PM
Registered User
Our local laser company is working on a 48 inch square machine. I can hardly wait for it to be up and running. I have visions of quarter scale Ditchburn Vikings and Minettes. Maybe with a Baby Boot thrown in for good measure. What are you planning to power Swallow with? About 41 inches I think you said?
Mar 30, 2011, 06:09 AM
Registered User
szmyk's Avatar
Well..good question.
Im planning to use brushed Speed 600 with 35mm propeller.There's a 500mm shaft with about 300mm housing to provide low angle of thrust.
That will be temporarily set to make trials on water..
Later on i will replace the motor with marine brushless.

Mariusz
Mar 30, 2011, 05:14 PM
Registered User
szmyk's Avatar

Small update


Everything fits without any problems so far..









Mariusz
Mar 31, 2011, 12:04 PM
Retired for now
This is looking great and it's moving right along. Good build. pete
Mar 31, 2011, 12:21 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by norgale
This is looking great and it's moving right along. Good build. pete
Thanks Pete
Mar 31, 2011, 01:42 PM
Registered User
Is that a composition keel I see?
Mar 31, 2011, 02:13 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Nederlander
Is that a composition keel I see?
Yes, that's obeche/wallnut/obeche..
I need advice guys..
I should make first planking with obeche or balsa?..
Previously I was thinking about making one planking directly with mahogany..
But it will be better to make two I think..(?)
Mariusz
Last edited by szmyk; Mar 31, 2011 at 03:03 PM.
Mar 31, 2011, 03:47 PM
Tinkerer in Training
RGinCanada's Avatar
Not only is the design beautiful, but you have a good eye for photography. I am thoroughly enjoying your work!

Would it be rude to ask how much laser cutting the frames cost?
Mar 31, 2011, 03:57 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by RGinCanada
Not only is the design beautiful, but you have a good eye for photography. I am thoroughly enjoying your work!

Would it be rude to ask how much laser cutting the frames cost?
Thank you RGinCanada, I'm glad that you like it.
Laser cutting of my parts (20 stations and small bits) costs about £28 without material.
I've prepared all drawings for them, because if they would do it, they will charge you. I have no problems with this company, easy and painless..
And..my second hobby is photography..
Regards
Mariusz
Mar 31, 2011, 10:09 PM
Registered User
I think double planking with 1/16 inch stock. I prefer linear inside and radial out but that is up to you. Balsa inside is easiest to fair, then soak with clear penetrating epoxy sealer but stain first to match the color of the finish planks to avoid white show through. Photography eh? What format do you prefer? I always enjoy setting up a view and waiting for just the right light. Unfortunately they finally did take my kodachrome away...
Apr 01, 2011, 04:02 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Nederlander
I think double planking with 1/16 inch stock. I prefer linear inside and radial out but that is up to you. Balsa inside is easiest to fair, then soak with clear penetrating epoxy sealer but stain first to match the color of the finish planks to avoid white show through. Photography eh? What format do you prefer? I always enjoy setting up a view and waiting for just the right light. Unfortunately they finally did take my kodachrome away...
I will go first for 1/16 obeche and 1/16 mahogany then.

In regards of photography, since I have 1st Pentax I began to be "Pentaxian" . I have K20D with some older and newer lenses.
My second camera is 645N medium format.
I've sent you PM with link to my works..
Mariusz
Apr 01, 2011, 11:45 PM
Registered User
I am finally going to ask after giving this several days of contemplation; what are the cut outs in the transom for?
Apr 02, 2011, 07:04 AM
Registered User
Awesome build ! Look`n forward to the progression of it
Cecil
Apr 02, 2011, 12:39 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Nederlander
I am finally going to ask after giving this several days of contemplation; what are the cut outs in the transom for?
Hello.
These are cut outs for the exhaust. I would like to cover it with some sort of heat cover.


Thank you Cecil
Apr 02, 2011, 01:03 PM
Registered User
Gravman's Avatar
Man oh man what a beauty. You have done a fantastic job.
Apr 02, 2011, 06:03 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Gravman
Man oh man what a beauty. You have done a fantastic job.
Thanks..
I'm planking the bottom of the boat now..will post some pic's tomorrow.
Mariusz
Apr 04, 2011, 04:05 PM
Registered User
szmyk's Avatar
There is a small progress in my work..






Apr 04, 2011, 04:14 PM
Tinkerer in Training
RGinCanada's Avatar
Small progress... pbthhhhp!

You are flying along!
Apr 04, 2011, 04:31 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by RGinCanada
Small progress... pbthhhhp!

You are flying along!
I've had busy weekend..First photo session in my life..
But i have to touch my boat every day..You know that..
Apr 06, 2011, 05:38 PM
Registered User
szmyk's Avatar
Hello everyone.
I didn't asleep yet..
I'm not sure if I did it right by releasing the hull from the jig..
But it happened..
Bottom planking is almost ready, also the sides are partially covered.
It's starting to look like a boat now..
Mariusz




Last edited by szmyk; Apr 06, 2011 at 06:27 PM.
Apr 06, 2011, 06:22 PM
Registered User
that is one beautiful looking boat!!
Apr 07, 2011, 12:32 AM
Spreckels Lake, GGP, SF, CA
craig_c's Avatar
This thread added to WOODIES: Wooden Pleasure Craft Build Logs listing.

Path: RCGroups -> Boats -> Scale Boats ->"WOODIES..."

Lookin' forward to following along
Latest blog entry: Ah, To be young again...
Apr 07, 2011, 02:21 PM
Registered User
szmyk's Avatar
Thank you craig_c.
It's pleasure to be here..
Apr 08, 2011, 01:41 PM
Registered User
szmyk's Avatar

The rudder


I've made up the rudder. It will be more polished..later.
I found that the most difficult part of planking is transition from sides to deck..




I will back soon..
Apr 08, 2011, 02:07 PM
Registered User
SZMYK- I have been studying the hulls line you have posted and the construction of the hull interior and see what I think could be a problem down the line. First I notice that you have taken the extreme rocker out the hull bottom, which is a good thing , but if you place a straight edge on the planning surface from the transom forward, I think you will notice that the keel and stem post will not be lifted clear of the water surface by much if at all.

The reason I think that this may be a problem is that a planning hull will drop its bow when it goes into a turn and with your stem post already touching the surface of the water could cause the hull to hunt or even dig in causing the boat to swap ends when in a hard turn.

The second thing I noticed is the extreme forward placement of the motor in the hull going by the where the stuffing box is entering the interior of the hull. I realize that you are trying to have a flat shaft angle for better thrust, but care must be taken to move weight of the batteries aft to get good balance of the CG on the hull. Normal balance on the hull is between one third and one half the over all length of the hull measuring from the transom. Also watch how much you tuck or roll in the chines going toward the transom from their widest point on the hull. Since it will cause suction or drag on the hull if done to extreme. You will also be loosing lift of the hull due to the decrease of bottom area.
Apr 08, 2011, 03:41 PM
Registered User
szmyk's Avatar
Hello frankg.
I'm not specialist in designing and this is my first attempt.
What I was trying to design, is more racing runabout than pleasure boat.
I believe that you have more experience in boats than me, so maybe you have right.
I understand that this boat will not be able to make tight turns because of it's length.
Well..we will see, when I will finish and release the swallow to the water.
I know that CG must be in 1/3 of the overall length.
Before installing the equipment and first of all making the water lines, I will try to achieve the CG and compare it with the designing program.
Hopefully there will be no disaster on water..
I'm planning to make another boat in the future, so I will be in touch on this forum.
Of course I will post the movie and pictures from trials on water.
I'm sorry for misspelling.
Best Regards.
Mariusz
Last edited by szmyk; Apr 08, 2011 at 05:13 PM.
Apr 14, 2011, 03:50 PM
Registered User
szmyk's Avatar

Update


Couple of pictures from dockyard:




I've just checked mahogany strips for planking ordered from CMB a week ago.This is amazing!!
They sent 53 strips instead of 80, 7 of them was 1,5mm as ordered, rest of it is 2mm!!
They're amazing..
Last edited by szmyk; Apr 14, 2011 at 04:08 PM.
Apr 14, 2011, 06:13 PM
Tinkerer in Training
RGinCanada's Avatar
Sorry to hear about your issues with planking from CMB. Have they offered to correct it?
Apr 15, 2011, 04:02 AM
Registered User
szmyk's Avatar
Quote:
Originally Posted by RGinCanada
Sorry to hear about your issues with planking from CMB. Have they offered to correct it?
No, but i will send complain letter about that.
In regards of wood this company it's waste of time and money.
Apr 16, 2011, 11:23 PM
Registered User
why dont you lazer the vents out of wood then use silver leafing on them you get the look of metal but the easy workability of wood just a thought. I love the lines on this thing what program did you use to draw it out? I would like to play around with this as well
Apr 17, 2011, 08:16 AM
Registered User
bboarder711's Avatar
i just drooled all over my desk thank you haha Great work I would really love to be able to draw up some plans like that and have some laser cut frames be sent in the mail.
Apr 17, 2011, 09:17 AM
Retired for now
I agree. This is really a slick looking boat. I love the concave hollows which I assume are for the exhaust and the transome is very interesting. Great job . Pete
Apr 17, 2011, 11:19 AM
Registered User
szmyk's Avatar
Thanks guys..
I've made the vent, but I'm not happy with this shape..should be more flat I think. It's just try.
Apr 17, 2011, 04:39 PM
Registered User
The vent looks good to me. There were a lot of different shaped vents out there. The Hacker Craft vents at least the late 20's and 30's were not flat
Apr 28, 2011, 01:40 PM
Registered User
szmyk's Avatar

There's a little progress..:)


I have had lots of other things to do last couple of weeks, but the boat is getting better..Now I'm installing the rudder housing and hatch frames on the deck.


Apr 28, 2011, 01:47 PM
GILL
GILL RC's Avatar
Maybe a little progres, but looks great.
Apr 29, 2011, 03:02 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by GILL RC
Maybe a little progres, but looks great.
Thanks very much..
Jun 01, 2011, 09:38 PM
1/2 a bubble off
Apismelifera's Avatar
You haven't been posting. I hope everything is Ok.
Jun 02, 2011, 04:40 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Apismelifera
You haven't been posting. I hope everything is Ok.
I'll be back in a couple of days. I just came back from holiday..
Mariusz
Jun 03, 2011, 03:06 PM
Registered User
Welcome back Mariusz! Hope the vacation went well.

Mike
Jun 06, 2011, 02:17 PM
Registered User
szmyk's Avatar
Hello every one..
Yes, vacation went well, but I didn't rest too much
I'm doing finishing touches before the second planking with mahogany.
As is very hard to get pear wood in London, I bought mahogany strips from Model Shipyard. I must say that these are lot better than CMB and I have all 1,5mm as ordered.
I'm preparing some metal fittings before the second planking:

Did some one used UHU Contact glue for planking, or better to use cyanoacrylate?
Jun 20, 2011, 10:23 AM
Registered User
szmyk's Avatar

Planking 2


Hello.
Shaft housing is on place glued with silicone to reduce the noise.
I've started the second planking today with mahogany strips.
Have thumbs all in cyanoacrylate


Jun 20, 2011, 10:26 AM
Tinkerer in Training
RGinCanada's Avatar
I've been waiting for this update! Looking good!
Jun 20, 2011, 11:05 AM
Woodfumbler......
Sharky1dk's Avatar
AWSOME is not a strong enough word for this magnificent boat it is Superp.

When i got to first read it in thread today the picture of the aft with beginning mahogany planking. it was a sight gods whorty.

This one sure gonna fly like a swallow.

I would wish i got a place here in Copenhagen where they did lazercuts its just stunning.

I use UHU hart for planking, and so far i have no problems.

Just one question.. Where did you get that shaft housing? It would look awsome on my Riva. as the one delivered in the kit were only worthy for a display boat. So i am going to get me 2 like your's.

THANKS for making this build log. I LOVE IT...

Robert
Last edited by Sharky1dk; Jul 05, 2015 at 08:17 AM.
Jun 20, 2011, 04:51 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Sharky1dk
AWSOME is not a strong enough word for this magnificent boat it is Superp.

When i got to first unread in thread today the picture of the aft with beginning mahogany planking. it was a sight gods whorty.

This one sure gonna fly like a swallow.

I would wish i got a place here in Copenhagen where they did lazercuts its just stunning.

I use UHU hart for planking, and so far i have no problems.

Just one question.. Where did you get that shaft housing? It would look awsome on my Riva. as the one delivered in the kit were only worthy for a display boat. So i am going to get me 2 like your's.

THANKS for making this build log. I LOVE IT...

Robert
Hello Robert.
Thank you for kind words. Hopefully it will "fly like a Swalow"..Have lots of work to do with my beauty.
I have shaft with housing from Model Dockyard, but manufacturer is "Caldercraft" that's their standard shaft.
Best Wishes
Mariusz
Jun 20, 2011, 05:35 PM
Woodfumbler......
Sharky1dk's Avatar
Ooh not the outer shaft... sorry i meant the support in the aft the the...the one holding it just in front of the propeller.

Thanks Robert.
Jun 20, 2011, 05:38 PM
Registered User
szmyk's Avatar
I've made it myself from 2 pieces of brass plates, soldered together.
Mariusz
Jun 20, 2011, 05:41 PM
Woodfumbler......
Sharky1dk's Avatar
Like the rest of your boat, they are superp..

Robert
Jun 28, 2011, 01:59 PM
Registered User
szmyk's Avatar

Update


I've finished the bottom planking today. Now the most difficult part for me..the sides planking and transition to the deck..



Jun 28, 2011, 03:34 PM
Woodfumbler......
Sharky1dk's Avatar
Drool..

Awsome i absolutely love this wavesplitting swallow..
Im confident that you will susceed on your planking it is looking superb...
Jun 28, 2011, 03:44 PM
Spreckels Lake, GGP, SF, CA
craig_c's Avatar
I am in love!!! Wow!

She is going to be something spectacular!
Latest blog entry: Ah, To be young again...
Jun 29, 2011, 01:00 AM
Taking care of the pond.
MILLERTIME's Avatar
Looking good.
Jun 29, 2011, 06:59 AM
Tinkerer in Training
RGinCanada's Avatar
You're gonna need a bigger pond
Jun 29, 2011, 07:51 AM
Registered User
szmyk's Avatar
Quote:
Originally Posted by RGinCanada
You're gonna need a bigger pond
Oh yeah..certainly.. Thanks guys for encouraging me..
That's the beginning..She should look better and better
I'm considering to paint the hull under the waterline with dark green dye..(if I will find)to expose the wood structure..Just thoughts..
Jun 29, 2011, 09:14 PM
Spreckels Lake, GGP, SF, CA
craig_c's Avatar
Quote:
Originally Posted by szmyk
Oh yeah..certainly.. Thanks guys for encouraging me..
That's the beginning..She should look better and better
I'm considering to paint the hull under the waterline with dark green dye..(if I will find)to expose the wood structure..Just thoughts..
Sounds like a great plan... and Lockwood dyes can give you any color of green your heart desires (you can mix the dyes... just make enough so you will have some for future touch-ups)!

(BTW, I agree, your woodwork is just way too nice to cover up under paint!!!)

From the Woodies reference list... with references to dyes, dying and Lockwood Dyes.
For example:
Water Based Concentrated Powders

Forest Green . . . .

Moss Green . . . . .

Oil Soluable (Use mixed in Turpentine)

Green Concentrate

Also check out the stains that they have specifically for Mahogany
Last edited by craig_c; Aug 01, 2011 at 12:24 AM.
Jun 30, 2011, 02:22 PM
Registered User
szmyk's Avatar
Thank you Craig!
The Forest green on the left side is what I'm looking for.
I will try to look for such color in local shops, if not, I will order it from "Lockwood Dyes".I've checked the prices and will cost me about £20 so it's not so expensive.
I have already spirit dye for all mahogany parts
Jul 11, 2011, 01:44 PM
Woodfumbler......
Sharky1dk's Avatar
Anny news?
Jul 11, 2011, 02:03 PM
uh, great
Jul 11, 2011, 03:54 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by Sharky1dk
Anny news?
I'm working quietly
Side planking is done, just slowly trying to manage the transition from sides to the deck. After that I'm gonna sand all hull.
Thinking about to use steel wool for scraping, but before I would like to make some kind of pad.
I've made the black frame for the deck as well.
The deck will be made with Paduc strips with white caulking.
Best wishes.
Mariusz







Jul 11, 2011, 05:02 PM
Woodfumbler......
Sharky1dk's Avatar
Looking good, that baby got some curves...
Jul 11, 2011, 05:18 PM
Registered User
szmyk's Avatar
My baby will get some curves soon..
Jul 11, 2011, 09:00 PM
Spreckels Lake, GGP, SF, CA
craig_c's Avatar
Ahhh.. SWEET!!!!!
Latest blog entry: Ah, To be young again...
Jul 12, 2011, 10:43 PM
1/2 a bubble off
Apismelifera's Avatar
Very nice.
Jul 19, 2011, 04:10 PM
Registered User
szmyk's Avatar

Now she have some curves..:)


Finally I finished bottom and side planking..Looks better than I expected.)
I'm starting the deck with red paduc stips/ white caulking.
Today I bought 24ct gold leaves for some ornaments and name on transom.
Fresh pictures below:






I hate when cyanoacrylate covering my fingertips
Jul 19, 2011, 04:21 PM
Tinkerer in Training
RGinCanada's Avatar
OOoooooooohhhhhh!!
Jul 19, 2011, 04:28 PM
Registered User
Gravman's Avatar
aaaahhhhhhh!!!!
Jul 19, 2011, 05:39 PM
Spreckels Lake, GGP, SF, CA
craig_c's Avatar
Oh baby, Oh baby, Oh baby!!!!

Lookin' great, Szmyk, you are doing a great job!
Latest blog entry: Ah, To be young again...
Jul 20, 2011, 03:27 PM
Registered User
szmyk's Avatar
Thanks guys!!
Jul 20, 2011, 03:47 PM
Registered User
tghsmith's Avatar
your making this look way to easy! are you planning a brass or chrome cutwater trim on the stem..
Jul 20, 2011, 04:27 PM
Registered User
szmyk's Avatar
Quote:
Originally Posted by tghsmith
your making this look way to easy! are you planning a brass or chrome cutwater trim on the stem..
The hull will be stained with deep mahogany dye above the waterline, below will be green dye to expose the wood grains.
Cutwater and all metal works will be in polished brass.
I hope it will look good..
Jul 20, 2011, 05:32 PM
Woodfumbler......
Sharky1dk's Avatar
You hope it will look good??

Granted... it already does.. '

As before stated it is superb....
Jul 20, 2011, 05:48 PM
Retired for now
Outstanding model. The design is beautiful and I'll bet she'll go like the wind. Very nice work. Pete


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Article "Mahogany in Scale: Modeling the Classic Runabout" Book Review Michael Heer Scale Boats 2 Dec 04, 2010 12:26 PM
Sold Dumas 1940 Barrel-Back Mahogany Runabout Bob SF Boats (FS/W) 1 Nov 07, 2010 09:59 PM
For Sale Sterling kit Mahogany Runabout sweptside Boats (FS/W) 0 Oct 14, 2010 02:25 PM
Discussion Sterling Models Mahogany Runabout MILLERTIME Scale Boats 10 Feb 26, 2008 02:39 AM
Off Site Sterling Classic Dual Cockpit Mahogany Runabout MILLERTIME Boats (FS/W) 0 Oct 14, 2007 08:57 PM