HOBBYKING CESSNA 182 1.5mts - What a cool aircraft! - RC Groups

This thread is privately moderated by rolrossi, who may elect to delete unwanted replies.

Mar 13, 2011, 10:50 PM #1
rolrossi
rolrossi FPV is lifestyle! Thread OP	Discussion HOBBYKING CESSNA 182 1.5mts - What a cool aircraft! A month ago started my new project: CESSNA with water floats. What a incredible aircraft! Take off or landing on the lake seems to be not so easy but I'll try. Because of the water surface, take off needs a powerfull motor or a long way to go faster or a better idea like huge flaps. Adding a cam on board, on my opinion, things get safer. That's a lot of job and a lot of $ I can't fail...and I won't! Feel free for add comments, please. Images View all Images in thread Views: 329 A/V TX fitting. Later I'll fix using double sided tape and plastic pull-ties. Needs first to choose the right antenna to go through the hood. Views: 269 Views: 270 Pitot tube final job. The air outside could obstruct the tubes so... Views: 229 Pitot silicon tubes to sensors inside cabin. Views: 242 Views: 270 Views: 263 Cooler for A/V TX while tests. A small screw inside front landing gear suport. Views: 235 Views: 209 "let me fly! let me fly!" Views: 168 ELogger Views: 166 RPM sensor + motor cables. Views: 161 ELogger. Views: 163 RX key on/off. Views: 172 Miscellaneous itens to find the best fit for 4mm shaft. Views: 235 Was not too hard to decide the best place to the cam pod. Views: 227 After some adptations the final result. Views: 224 I followed the same angle from the aircraft on the base of pod and also installed a longer shaft on it. Views: 238 I had to cut a little above the hood. Views: 210 Views: 228 Final result. Before I install the cam and all FPV system I made an aircraft test on the lake and had crash on the water that dropped the mount structure of the wing, but its fixed now. Maybe this won't happen again with FPV cam. Views: 161 Views: 162 Fitting stabilizer system. Views: 165 The best place I found for sensors...it will be necessary to have a good idea to fix windshields the way I could move anytime... Views: 161 Views: 161 Views: 158 Planning where to fix A/V TC Views: 165 I'll make tests before connect 433MHz system. Views: 152 Views: 153 My wife don't know about that hehe... Views: 159 FY stabilization system. Views: 162 OSD fitting. Views: 161 Ready for Scherrer LRS RX. Views: 156 UHF LRS TX, serializer, UBEC, FUTABA TX Views: 150 UBEC + serializer. Views: 142 LRS RX
	Last edited by rolrossi; Mar 13, 2012 at 10:44 PM.

Sign up now to remove ads between posts

Return to rolrossi's blog

Quick Reply
The following errors occurred with your submission

Okay
Message: Posting Quick Reply - Please Wait

Thread Tools
Show Printable Version Email this Page

Similar Threads
Category	Thread	Thread Starter	Forum	Replies	Last Post
Discussion	Huge 73" Foam Cessna 182 (Tian Sheng EPO Cessna 182)	I_Gotts_Ta_Fly	Foamies (Kits)	1498	Jun 30, 2020 12:02 AM
For Sale	CMP Cessna 182 1.20 size	hermperez	Aircraft - Fuel - Airplanes (FS/W)	4	Apr 13, 2011 04:20 PM
Sold	Pica Cessna 182 1/5 KIT 86"	Rainbow28	Aircraft - Fuel - Airplanes (FS/W)	1	Sep 19, 2010 12:50 PM
	what's difference between cessna 182 and cessna 172	CWNG06301	Scale Kit/Scratch Built	27	Sep 04, 2007 01:05 PM

Copyright © Website Acquisitions Inc. All rights reserved.