Nov 19, 2011, 05:36 PM
GEEBEE Can't WAIT!
perschek's Avatar
Ok heres the px at 93% don't really start on the pitch until 2:00 so skip the boring stuff lol. Look at how cool the orange blades look when spinning. See how well the tail holds at 2:00-4:00 into the battery, didn't blow out once...!
Brushless mcp X, 93% pitch test PASS! (4 min 3 sec)
Sign up now
to remove ads between posts
Nov 19, 2011, 06:28 PM
Registered User
Quote:
Originally Posted by Stugoose View Post
anyone wanna buy an mcpx minus a servo
How much.
Nov 19, 2011, 07:52 PM
Suspended Account
Quote:
Originally Posted by Martyn McKinney View Post
Tail motor increases RPM to full in order to compensate when rotating CCW.

Everything seems OK.

I'll try increasing tail rotor pitch, then a new tail motor.

Thanks! I did not know about lack of TX gyro adjustment. I did remember that I remembered that I had never previously set it.
Hey just put a Blade SR 120 tail prop (3.00$ US) that you cut 1/2 an inch each side and use CA to hold it right and Voila. My MCPX after that mod flyies with no tail blow out . I do not do 3D just quick sharp flying. Good luck and Best Regards.
Nov 19, 2011, 09:13 PM
Registered User
Stugoose's Avatar
i love the kbdd tail blade,
Nov 19, 2011, 10:23 PM
Registered User
Stugoose's Avatar
Mcpx inverted indoor (cruizin) (1 min 33 sec)
here is what ive been up to
Nov 19, 2011, 10:45 PM
GEEBEE Can't WAIT!
perschek's Avatar
Quote:
Originally Posted by Stugoose View Post
http://youtu.be/Z5uuQlGLks0 here is what ive been up to
nice flyin stu, can't wait until I can flip indoors I finally got the brushless upside down after 2 weeks of windy wet weather and it is 10x easier now. I think a combo of a bad main and the stock short boom was holding me back on my learning. Now if the weather could just hold up I'll be as good as you in no time, but unfortunently living on the north west coast = RAIN!!!!!! So........... Looks like next spring until I'm doing ceiling landings

Been spending alot of time flying the Beast when the weather is decent, because I'm so anxious for the new beast 3d and gee bee! I bought 2 new beast v1s and been doing harriers and hovering all over the neighborhood practicing because once I get the as3x beast and gee bee I'll be stylin! Plus if I crash I'll have 2 new airframes to swap guts out for
Nov 19, 2011, 10:48 PM
Registered User
Stugoose's Avatar
u know that is a stock mcp except for the swash, weighted blades and the kbdd blades on the tail v1 tail mnotor,


i have another one on the way i ordered by mistake so im gonna either sell off my parts heli or return the one thats on the way
Nov 19, 2011, 11:13 PM
Registered User
sideburn's Avatar
anyone know what canopy this is in berts brushless video? is it just a painted stock one?

bert kammerer mcpx bl ircha 2011 (5 min 6 sec)
Nov 20, 2011, 06:01 AM
Registered User
I am finally ready to upgrade my mcpx to brushless. I was thinking of getting the hawk-rc kit then I saw this at miracle mart. Looks interesting. Anyboby use it?

http://www.miracle-mart.com/store/in...oducts_id=8028

Wonder when they will get more in stock.
Nov 20, 2011, 06:22 AM
Vienna calling...
Donaldsneffe's Avatar
Quote:
Originally Posted by snackdaddy185 View Post
I am finally ready to upgrade my mcpx to brushless. I was thinking of getting the hawk-rc kit then I saw this at miracle mart. Looks interesting. Anyboby use it?

http://www.miracle-mart.com/store/in...oducts_id=8028

Wonder when they will get more in stock.
Hi,
it has never been in stock - so nobody will be able to tell you how it works.

I have it on mail-alert for many weeks now (guess, since the first day it has been announced at MiracleMart).

Walter
Nov 20, 2011, 08:32 AM
GEEBEE Can't WAIT!
perschek's Avatar
Quote:
Originally Posted by Donaldsneffe View Post
Hi,
it has never been in stock - so nobody will be able to tell you how it works.

I have it on mail-alert for many weeks now (guess, since the first day it has been announced at MiracleMart).

Walter
Same here I bet its been scrapped or they just cant get it to work right who knows.....

I'm happy with my c05 setup
Nov 20, 2011, 12:09 PM
GEEBEE Can't WAIT!
perschek's Avatar
Damnit..

WARNING: Don't use any amount of loctite on the main hub screw that connects it to the main shaft. My hole in the main shaft is stripped / elongated and while waiting for my new main shaft to arrive I tried to use a TINY amount of loctite on the screw. It caused the main hub to break :-( Oh well now I have an excuse to buy a new MH main hub and titanium main shaft so I can use loctite safely. I know its not good to use loctite on plastic parts but I had no other choice since I've already closed the hole with CA multiple times on both sides. Every "shakes" incident I have had has been directly caused by the main hub screw. It gets loose and then it causes shakes. I tighten it goes away. Then it loostenes itself and I get shakes again. SO I'm ending this problem now with a credit card lol
Nov 20, 2011, 12:13 PM
Registered User
Stugoose's Avatar
I add some crazy/ca glue on a screw and rethread the holes, works fine
Nov 20, 2011, 12:14 PM
1981 Z28 "The Wife"
leereyn's Avatar
I received my mCP X a couple of days ago and I have three flights on it. I'm very happy with it, but I have a question. As soon as I plug in the heli battery and bind it to the radio the servos start twitching and in flight there's an electric smell? Is this normal? It flys great, but that kind of worries me.
Nov 20, 2011, 12:26 PM
Registered User
Stugoose's Avatar
servos are constantly moving as it is flybarless, electric smell?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Blade mCP X BNF Heli... ChuckTseeker Micro Helis 15708 Jan 23, 2017 01:22 PM
Discussion Blade mCP X Discuss anything thread A Rdnek Micro Helis 457 Jul 26, 2011 11:34 PM
Discussion The New BLADE mCP X Has Arrived... ChuckTseeker Electric Heli Talk 38 Mar 27, 2011 07:35 PM
Discussion new blade mcp X anyone know anything new. epoweredrc Atlanta Area RC 6 Mar 16, 2011 08:14 PM
Discussion Blade mCP x - strictly on topic Q and A thread jdog83 Micro Helis 58 Feb 07, 2011 02:28 PM