Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Feb 01, 2011, 10:51 PM
JUERGEN_ is offline
Find More Posts by JUERGEN_
xxxxxxxxxxxxx
JUERGEN_'s Avatar
Quote:
Originally Posted by Goofy23 View Post
He said:"therfor is every bit exchangeble", which doesnt have a real meaning.
??who cares?? its a shield for a few expensive (old) sensor boards, like many others.
ja bei SPARKFUN,
die haben auch die lizenz zum geld drucken.
Sign up now
to remove ads between posts
Old Feb 01, 2011, 11:01 PM
Goofy23 is offline
Find More Posts by Goofy23
Registered User
Goofy23's Avatar
i translate.
"Yes at Sparkun, they also have the license to print money"
This is not an amswer which make sense in german, so its hard to comment in english cause there is no sense. If someboby wants to use expensive and old sensors from sparkfun, he is free.
Old Feb 01, 2011, 11:02 PM
timecop is offline
Find More Posts by timecop
Suspended Account
No, it makes a lot of sense in English.
Sparkfun is pure profit, over 100% on every component they sell. Thus, it's as if they're printing their own money. Nintendo is/was used to be referred to same way.
Old Feb 01, 2011, 11:07 PM
Goofy23 is offline
Find More Posts by Goofy23
Registered User
Goofy23's Avatar
but where is the relation to my flyduino?
I dont found it, you (jürgen) use those sensors not me.
I am not related in any way to Sparkfun.
Please have in mind big consumer electronic companys will laugh about 100% profit for a working unit.
Last edited by Goofy23; Feb 01, 2011 at 11:22 PM.
Old Feb 01, 2011, 11:21 PM
JUERGEN_ is offline
Find More Posts by JUERGEN_
xxxxxxxxxxxxx
JUERGEN_'s Avatar
Quote:
Originally Posted by Goofy23 View Post
I am not related in any way to Sparkfun.
das will ich aber hoffen.

du siehst ich kann nicht schlafen..
so..o neugierig bin ich auf dein konzept.
Old Feb 01, 2011, 11:26 PM
timecop is offline
Find More Posts by timecop
Suspended Account
I duno. Maybe he means his stuff has all sensors integrated on board or something.
shrugging.
Old Feb 01, 2011, 11:28 PM
Goofy23 is offline
Find More Posts by Goofy23
Registered User
Goofy23's Avatar
no he dont, you see the (sparkfun) sensors on top, as you can see on picture, (Jürgens) its only a shield like many others, i dont want to comment further on it, sorry Jürgen.
Last edited by Goofy23; Feb 03, 2011 at 08:58 PM.
Old Feb 01, 2011, 11:40 PM
timecop is offline
Find More Posts by timecop
Suspended Account
I also don't really see a point for making a new *duino board as a shield unless you're integrating all the sensors on it. Breakout boards are way too expensive and with directly attaching everything you need on pcb it becomes lighter, smaller, etc. If you're going to the trouble of making your own PCBs, why not. Anyway whatever.
Old Feb 02, 2011, 04:42 AM
kinderkram is offline
Find More Posts by kinderkram
OS Sponsor
kinderkram's Avatar

Great!


Another big step taken.
Also the size is nice. 5x5cm fits on most copter projects (a standard for KK & MK boards). If we combine it with Jussi's IMU we'll have a great base for multirotors!

The 4,5x4,5cm holes make it easy to produce stacks for the sensor boards like this:


It's all very exciting!

Norbert
Old Feb 02, 2011, 08:53 AM
JussiH is offline
Find More Posts by JussiH
Friend is a 4 letter word...
JussiH's Avatar
Quote:
Originally Posted by timecop View Post
I also don't really see a point for making a new *duino board as a shield unless you're integrating all the sensors on it. Breakout boards are way too expensive and with directly attaching everything you need on pcb it becomes lighter, smaller, etc. If you're going to the trouble of making your own PCBs, why not. Anyway whatever.
I disagree on that...

Sensor technology is moving by an alomost exponential rate these days, so to tie a design to a certain sensor solution right now, would to me be a limiting factor! - some want the "full monty sensor array" while others are perfectly happy with just a WMP!

And in two months from now you will all be raving again over some new sensor that just hit market with something like "9Dof/GPS MPU that can tell the direction and velocity of your farts" or something else to that effect....

One of my big beefs with almost all current Duinos, is the fact, that either they are DIP-package like the smaller ones, or else they all seem to be more or less derived from the original Diecemila footprint.... and excuse me for saying so: That one must have been dreamed up by a designer who drank too much poor italian red wine. An assymetric board, with only 3 holes for mounting and a downright stupid pin placement and spacing....its just not a very good solution in terms of mounting or fitting to multirotor helis!

I think Paul has come with something good here - It almost perfectly suits my needs for a flexible "Mega" flight-duino with relevant inputs and outputs in a formfactor that makes sense!

(If I were to make one comment it would be to move the motor and RX headers to the outline of the board and converting them to angular ones, so that plugs goes into the side of board instead of from top!)

Keep up the good work!
Old Feb 02, 2011, 10:28 AM
JUERGEN_ is offline
Find More Posts by JUERGEN_
xxxxxxxxxxxxx
JUERGEN_'s Avatar
Quote:
Originally Posted by 420RcPilot View Post

.... and excuse me for saying so: That one must have been dreamed up by a designer who drank too much poor italian red wine. An assymetric board, with only 3 holes for mounting and a downright stupid pin placement and spacing....its just not a very good solution in terms of mounting or fitting to multirotor helis!


...
and therefore we need a Flyduino.
and a very affordable WiiDUINO.
Last edited by JUERGEN_; Feb 02, 2011 at 10:37 AM.
Old Feb 02, 2011, 09:10 PM
Goofy23 is offline
Find More Posts by Goofy23
Registered User
Goofy23's Avatar
420RCPilot is completly right, i also think its the better choice to seperate the sensors.
At least this gives you better vibration dampenig options, and believe Jussi, he knows every Sensor.
Old Feb 02, 2011, 09:16 PM
timecop is offline
Find More Posts by timecop
Suspended Account
Lol ok, you're the man.
<chorus> I'm a barbie girl, in tarduino world
Old Feb 03, 2011, 07:21 PM
Goofy23 is offline
Find More Posts by Goofy23
Registered User
Goofy23's Avatar
Seems to work, have a look on the first side, i posted some pictures.
Old Feb 04, 2011, 07:23 AM
kinderkram is offline
Find More Posts by kinderkram
OS Sponsor
kinderkram's Avatar
Quote:
Originally Posted by Goofy23 View Post
Seems to work, have a look on the first side, i posted some pictures.
Sounds great!

Can't wait to have one here...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Please let me introduce myself jimaquo Dock Talk 7 Oct 27, 2010 03:27 AM
Let me introduce the DEMON!!!! (Transparent covering and eliptical wing!!!) modest-master Sport Planes 7 Aug 26, 2002 12:46 AM
Let me introduce Angelis 280/400, Benjamin, Zombi (ARFs) modest-master Parkflyers 17 Mar 14, 2002 02:20 PM
Let me introduce the "NIKE" modest-master Electric Sailplanes 3 Mar 07, 2002 06:20 AM